Hey how did you figure out which was the blinker line? Tested all mine with a reader to see and all of them had a constant voltage if car was off/on and same w blinkers.

@nate86diy43

Жыл бұрын

Hey there, thank you for asking. I did not have a tester with me before, what I did before, I inserted the bare copper(DRL/turn signal) wire to one of the male connector of the stock turnsignals, to determine which one was the turn signal. Otherwise, I would have to splice each to figure out which one was the turn signal wire. Hope this helps. Good luck!

Are these lights LEDs? I wasn't sure if a load resistor would be necessary.

Can you share the wiring diagram?

what did you use to black out you logo and v grill

@nate86diy43

3 жыл бұрын

hey mate how r u. I wrapped them with Satin Black :)

bro,I ordered similar arrows,I tried to connect the red cable to the positive pole and the black cable to the negative pole... they don't light up... Should I think they are defective?

@nate86diy43

11 ай бұрын

Have u tried trying to direct test from the battery? If it works then the wiring must redone. Else it is a defect.

Hey did you paint the bottom piece on your bumper black?

@charleslastname8587

Күн бұрын

I'm very sure it was wrapped. Did the same to mines. Easy to do especially if you have knifeless tape.

@Melvynnielsen

Күн бұрын

@@charleslastname8587 Gotta see if i can find some knifeless tape and try to wrap it. I think it will look so smooth with the front splitter :D

have you ever had a problem connecting it to that fuse, and what exactly is the fuse location😀

@nate86diy43

3 жыл бұрын

hey mate, never had a problem at all. I planned before hand of where I will tap the positive into. I tapped into the ignition Fuse. Reason for that is I like my drl switched ON at all times. I can tap it onto the headlight if I want it too or the parkLight ;)

Hi, can you show the exact fuse that you connect the red wire to? Thanks

@nate86diy43

Жыл бұрын

Connected it to the ignition fuse

Is it hyperflashing?

@nate86diy43

3 жыл бұрын

No hyper flash

paano nyo nga po ulit e kinonect ang DRL na mag oon lng kapag umandar lng ang makina ? may nagsasabi kasi na dangerous daw ? totoo ba yun ? kasi nag install ako ng crystal DRL sa suzuki celerio ko tapos sisindi lng ang DRL kapag nakatapat na ang susi sa on without the engine turned on..hindi ko nalang kinonect ang turn signals..ang gusto ko po kasi mangyari is sisindi lng ang crystal DRL's kapag umaandar na ang makina..paano po ?

@nate86diy43

3 жыл бұрын

I tapped onto the ignition relay, not the engine. you can tap as well to constant power when car is running.

@nate86diy43

3 жыл бұрын

Pardon me, i tapped into the Ignition fuse. I dont think it is dangerous because when activates, the drl resistor is inserted on ground side, replacing the normal direct ground path through bcm. this result in approx +9 volts dropped and the remaining +3volts are dropped across the drl resistor. As you probly know, with engine running, alternator will add 1.5 volts or more to the batt. DRL LEDS draw such small amount of current and voltage. if you connect a drl or any light system that do not have a resistor, chances of risk will be likely. So dont buy a drl that do not have resistors.

So I installed some similar drls but after tapping into the same ignition fuze my car doesn’t actually start. The dash comes on and the drls work perfectly along with the turn signal but the it car isn’t actually starting. Edit: after comparing more it looks like when you tapped into the ignition fuze there is a 10 amp fuze in your tap, my car had a 15 amp fuze in that slot so when i put my tap in i put a nother 15 amp fuze in the tap, is that an issue at all?

@nate86diy43

3 жыл бұрын

yes that is correct, if you are tapping onto the fuses.

@Jeff-lo4ud

3 жыл бұрын

@@nate86diy43 so i would need to get a 10 amp fuze for it to work?

@nate86diy43

3 жыл бұрын

@@Jeff-lo4ud Yes

@Jeff-lo4ud

3 жыл бұрын

@@nate86diy43 just out of curiosity and for the sake of learning, why do i need a 10 amp fuze for the tap when its going into a spot where a 15 amp fuze was

@nate86diy43

3 жыл бұрын

@@Jeff-lo4ud to retain the circuits original intended protection and provide a means for you to create a second circuit to have an equal or lower rated ampacity. You DRLs are rated for 5amps.

where are you located sir? NCR ka ba?

@nate86diy43

3 жыл бұрын

I am located in Cebu City

@HansLotap

3 жыл бұрын

@@nate86diy43 sayang layo mo. sayo sana ako papainstall ng DRL at ambient light strip. hahah cge lakasan ko nalang loob ko at gayahin mga ginawa mo. salamat marami :D

@nate86diy43

3 жыл бұрын

@@HansLotap I am sure you can ;) Good luck.