How To Install Ball Bearing Drawer Slides
amzn.to/3mI2qBJ 10 pack of Ball Bearing Slides
amzn.to/38z6qiQ Phillips Extension Bit Makita 6"
amzn.to/38tzM2i 6 Pair of Ball Bearing Slides 22"
amzn.to/3hfwfs4 10 Pack of Drawer End Brackets
amzn.to/2KNMgth Cabinet Screws
amzn.to/3hkYAgY Head Lamp Light
In this video, I show you how to upgrade your factory kitchen cabinet from vinyl rollers to ball bearing slides.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.
Пікірлер: 80
After searching for hours this was the absolute BEST method I saw on YT that didnt require buying drawer jigs! Thank you!
Absolutely the best and easiest way to install drawer slides. I did one thing differently. Instead of cutting a board to get the wall space and height for the back bracket I used a piece of 3/4” wide trim piece to space the wall with a clamp at the height to rest the rail on. You made it way easier to install. Thanks again!
Put in a trash can drawer in our island. Its been giving her troubles for weeks. pilot holes critical . now she thinks I am a carpenter. I know that mind of hers is working overtime for something she wants...so I am hesitant to say thank you. seriously great instructions to the point. Thanks Friend
After searching and viewing several videos, this is the first one that I've found that have cabinets built like mine. I also have that gap from the inside of the cabinet to the face frame. All the other videos I've watched have the rail mounted right against the inside of the cabinet. So with that gap, I also have to use an End Bracket as you do at 4:51. And now with the "Oh duh, why didn't I think of that?" jig you made as shown at 5:02, I now the confidence that I can get this project done, and surprisingly easy at that. Thanks for taking the time to show us how to upgrade drawer slides. I sincerely appreciate it!
@dfhowes
4 ай бұрын
Follow up: Yup, turned out as expected. The jig made this a simple project. Quick and easy.
Thanks for the cool tip on making a guide for mounting the slides inside the cabinet
Thank you! Clear and concise instructions. I appreciate the home repair videos!
The question of the day is how happy that makes Mrs double wide as they happy wife happy life 👍
@doublewide6
3 жыл бұрын
I believe it went something like this, "Of all the cleaning and mess in the house, I wish you would work on something that matters" Yes a sign of a great marriage:)
@robertmailhos8159
3 жыл бұрын
@@doublewide6 okay thanks for your reply oh by the way do you know what the size is the nut that holds the fly wheel on a opposed twin cylinder Briggs and Stratton enigne
Thank you so much for this great tutorial! I'm installing all new drawer boxes with soft-close hinges, so explainging how to line them up on the new drawer boxes was very helpful. And the bracket to hold up the hinge to keep it level was a game changer!! 2 thumbs up!
Bob’s Small Engines and Kitchen Remodeling...I love it!!! Great video Bob, Happy Holidays to you and yours!!
@doublewide6
3 жыл бұрын
Hey Kenny, my real speciality is woodworking, but I do so much of it at work, that I do the small engine stuff at home.
This is better instructions than what you get with the slide kit. You have to have 4 hands following those instructions.
hope you and your family have a very merry christmas
@doublewide6
3 жыл бұрын
Happy holidays!
Thanks for posting. Just thought about doing this today!
The screws stripped out on the drawer and I could not figure out how to release the slide. You did it in the first couple minutes. Thanks for showing us how.
Wow, the best explanation and instructions ! Thank you so much.
Nice tutorial he made it simplier to understand how to set up things perfectly....max score.
Thank you! Very straight forward.
Great idea, looks like an upcoming project for me. Also wonderful to see the family involved!
Very helpful video, thank you
That is an awesome upgrade to the drawers
@doublewide6
3 жыл бұрын
Yes they are pretty nice and under $200
Best and clearest video on installing these by far….many thanks 👍
@doublewide6
2 жыл бұрын
Glad it helped
Nicely explained. Thx Bud!!
@doublewide6
3 жыл бұрын
Glad it helped!
Keep it up sir and more power to you channel...👏🤟
Well explained
HI, this is great, same sort of replacement thanks!
Supplies and Tools From Video: amzn.to/3mI2qBJ 10 pack of Ball Bearing Slides amzn.to/38z6qiQ Phillips Extension Bit Makita 6" amzn.to/38tzM2i 6 Pair of Ball Bearing Slides 22" amzn.to/3hfwfs4 10 Pack of Drawer End Brackets amzn.to/2KNMgth Cabinet Screws amzn.to/3hkYAgY Head Lamp Light
Merry Christmas to you and your family!!! Happy New Year!!!
Thank you for showing me how to release the drawer runner, just assembled a desk and didn't have clear instructions
GREAT DEMO MY FRIEND .VERY NICE .FROM DOUG
@doublewide6
3 жыл бұрын
Happy new year buddy thanks
@fleetswoodshop3339
3 жыл бұрын
And a very very happy New year's to you and your family my friend and thank you
thank you!! :D
Thanks for the instructional vidio. I installed the exact same ones. This vidio helped tremendously. However, I had trouble holding my screws to attach the bracket holders in the back. Since my screwdriver attachment on my drill wasn't magnetized I couldn't start the screw. I cut pieces of electrical tape approximately one inch and stuck the screws through it and folded the tape back and taped it to my screwdriver shank. Started my screw , then reach back and pull the tape off then finish tightening it. Hope this helps someone. No more lost screws.
@killtyrant
Жыл бұрын
That's actually quite a useful tool hack, I'll have to give it a go
Great! Thanks. I didn't know where to start since I lost the instructions. This will work out great. I think I need more screws though? No?
Oh so close to 100k subscribers
Thank you
Good👍
I ve looked at a lot of these videos and all of them assume installed cabinets are square and level. When installing these in existing cabinets it’s would be important to make sure rails are square with face frame, level, and both rails are parallel. This is important information for retrofit
I see that there are more holes in the end bracket that once you get the right position of the bracket you can add more screws to give it strength and holding power for heavy drawers.
Great video Bob My wife wants to know when are you coming to install these on our drawers? LOL
@doublewide6
3 жыл бұрын
Not sure yet. Maybe New Year's Day?
@nashguy207
3 жыл бұрын
@@doublewide6 She said thats fine with her. LOL
Sugest me best adjustable wrench
Big improvement. How did the rest of the drawers go? Maybe you should ask for one those fancy drawer slide jigs for Christmas.
@doublewide6
3 жыл бұрын
The rest of the drawers went well. I was one back bracket short because they came in packs of 5, so I cut a set in half and welded them for 2 drawers. Worked out perfectly.
Oh very posh.. good one bud..
@doublewide6
3 жыл бұрын
Thank you kindly. These would work for a pull out work tray as they support over 100LBs.
Thank you for a clear instructions. Just wonder how strong these ball bearing slides are if they are installed only on one side of a tall narrow drawer. I have a cavity where I'd like to install a 24" by 24" and 6" deep cabinet that can be pull out for storage. I'd like to install two of these slides on one side of the cabinet.
@TheOneTheyCallDean
Жыл бұрын
I don't have these slides myself just yet, (I'll be getting mine in a few days,) but if you space your slides as far top and bottom as they can go, and if your contents aren't too heavy, that configuration might be able to work. Conversely, it might also be too heavy for the bearings' retainers and they could "pop out" from the lateral tension. Hope you let us know your workaround! 😊🌎✨
I light that illuminated the back of the cabinet would have been helpful
5:50 to much power 🤣
You dont need any wooden jigs. Just measure and use double side tape to secure slide to the cabinet. Then screw it . Done
@James-ms2mx
Жыл бұрын
No. The rail sits away from the edge of the cabinet. It isn’t flush against the side.
Is my dad he is great subscribe
My droor feels resistant and it struggles to close, I can't seem to fix it no matter how many time I try to pit it back in, what's more all the balls keep falling out!
Have an issue with one drawer with this type of slide; it glides open by itself. Appears that the interior slide needs to be raised but how does one do this with the interior glide still in place? The drawer is in a tight corner next to the stove and is not easily removed or reinstalled. Can you advise, please?
@doublewide6
3 жыл бұрын
you are going to have to remove the drawer to fix. You will get it.
I noticed you had to pull a little bit on the drawer to open it. Is that because of the soft close mechanism?
@killtyrant
Жыл бұрын
The soft close mechanism has a spring you're fighting against so it might provide resistance the first 2 or 3 inches when opening. Think this is why he showed that you can remove it should you not like it
We jus gonna roll past that prt where he farted at 5:50? when he was first putting the track in the guides?
HI
Installing same slides and tolerances are to tight, the old slides are a about a sixteenth inch narrower making it to tight.. have a fix?..
@CutterElfquest
Жыл бұрын
Only one fix….chisel a channel.
What size screws did you use please?
@killtyrant
Жыл бұрын
Those are specifically called cabinet screws
@johnbies7041
Жыл бұрын
What SIZE screws shall I order? Ball bearing drawer slides often do not come with screws.. thanking you in advance
@killtyrant
Жыл бұрын
@@johnbies7041 #6 is typically the best size for this.
Well - pretty good video, however I wanted to see you get down on your belly and tackle that bottom drawer slide!! you missed the most difficult part of that upgrade!!! minus the cussing and groaning, if I had a little young lady she couldn't be in the same neighborhood by the time I get done with that install!! with all the cussing
the sound is not good I am quite disappointed
There is no reason this video needs to be 7 minutes