How to install a New downpipe in a boxed eave
Тәжірибелік нұсқаулар және стиль
See how to make and install a new downpipe into your gutters and make them more efficient at removing water. This is a step-by-step tutorial of how to do just that.
Work done by 24:3 Building W.A. 0415119313.
Пікірлер: 32
You bloody legend ! screwdriver and hammer for the cut out! Legendary ! Straight up no dicking around wicked video ! and top it off with from Perth made my day mate hats off to you and bet your phone hasn't stopped ringing after that rain the other night...
@dennisperrie
Ай бұрын
thanks for the comment and yes I am flat out after the rains👍
Best drywall cutting I’ve ever seen! Just with a screwdriver and a hammer !! Mastery right there.
Good video mate. This helped me a fair bit replacing a few downpipes on my house.
so going to give this a go after this weekend rain. if i stuff it up I might have to call you to come out (im gossy based)
Great video mate, cheers,
They should have chose the colour monument to match the specks in the bricks
En mi país eso es chapuceria.
Good evening sir! Please show me how to make an offset of downpipe 100 by 100 please!! Thanks a lot.
@dennisperrie
Жыл бұрын
I will when I get a job using that size downpipe.
Hey. Unsure if you still check older post comments :) how the heck do you do a side elbow in this type of downpipe. Mine comes off the side of a custom box gutter.. so bends along the 45 mm side to the wall to bend 90° down. Cheers :)
@dennisperrie
15 күн бұрын
so it is the same process except for the measurements. measure the big side measurement and take 5mm off it to get the cut.
@voraxe
7 күн бұрын
@@dennisperriecheers. I had assumed when I listen to the video again it would be something like that. I should have just thrown the contractor some coin to do it for me lol. I mean he gave me the downpipes for nothing.
Sorry I can’t find the number of the end. Please show me the number of female and male to connect the square rain downpipe 100 by 100. My one was leaking. I would like to cut a part and joint it. Thanks
@dennisperrie
Жыл бұрын
Just try sliding one inside the other.
Hi , Thank you. Do all makes of drain/down pipes have a small end?
@dennisperrie
Жыл бұрын
Yes or and end that sides into the other with a crimp. I haven't come across a make that doesn't.
Good evening sir! I’m Chanh , I’m very interested you did on your youtube. I got a square rain downpipe 100 by 100 was leaking. I would like to fix it by myself. But I need a female and male for fit it. Please tell me what size for it ! Thanks a lot!!
@dennisperrie
Жыл бұрын
You should still need a 100mm downpipe. It will have a big end and a small end. Check the ends they usually mark the small end. Just be careful because sometimes different brands are slightly different sizes.
What are the nails with inserts you hammered into the masonry called and are they commonly available? I have to remove some downpipes to replace pvc damaged by whipper snipper.
@dennisperrie
9 ай бұрын
They are 6.5mm nylon anchors.
@Wowwwzaaa
5 ай бұрын
Why don’t you just cut some pvc pipe, make a slit , add some PBAC glue in the inner part and the. push it over the damage pipe ..put pressure on the new piece for 30 sec!
@blurtmenow
5 ай бұрын
The repair is for a fitting at the bottom of downtube not a pipe. downtube(rectangle) to round pipe in ground was damaged by whipper snipper .the downtube needs to be removed to access broken fitting. Not a fun job. if there was an easy fix i would go that way. @@Wowwwzaaa
Is that asbestos you're cutting into?
@dennisperrie
Жыл бұрын
no it's hardiflex
@JohnBoyWalton06
Жыл бұрын
Doesn’t mean it doesn’t contain non fibril asbestos.
@dennisperrie
Жыл бұрын
@John Hull but there is no dust and the cut is clean. It is the safest and easiest way to cut the hardiflex
@deanwitt7903
Жыл бұрын
@@JohnBoyWalton06so what if it is ! The job has to be done regardless. You think cutting a little hole like that means instant lung cancer and a death sentence ?
@donburke4886
Жыл бұрын
Definitely asbestos.. You can tell by the sound of it.
Is it possible to cut the pipe on the other face (the 50mm face instead of the 100mm) and make these bends? Would you use similar measurements?
@dennisperrie
Жыл бұрын
Yes use 5mm less so if it is a 100 face cut at 95mm
@hepburn118
Жыл бұрын
@@dennisperrie Thanks Dennis, I want the downpipe to turn a 90 degree corner from where it is and I am clueless with sheetmetal. Your instructions for the bend you did on the video were great, I just wasn't sure they would translate to folding up the 50mm side. So thankyou again.