Good teaching skills. Thank you.

Wow you earn my Subs bro! I got Nissan rogue 2023 too!.

Based on my understanding on how the battery pack works, if you start your car, your battery pack will be charging and at the same time provide power to the dashcam(passthrough) and when you turn off your car, the battery pack will still provide power like if your car is turned on and will continue recording until the battery pack juice is depleted. Correct me if I am wrong, but the way you explained it if you turn off your engine, it will engage your dashcam into "PARKING MODE" which basically means its the equivalent of just hardwiring your dashcam into the fuse box directly.

@dial2fast

11 ай бұрын

The output wire of the battery pack to the dashcam has 3 wires: battery 12v, ignition 12v, gnd. When ignition is on, the dashcam is powered by the ignition 12v wire. When ignition is off, it's powered by the battery 12v wire. So the dashcam has 2 different power input source. The battery pack will automatically switch the output power from one wire to the other (depending on ignition on/off). The dashcam will sense which power it's getting, and switch between normal recording and parking mode recording. So the dashcam does not do normal recording when ignition is off. Also this logic is same as hardwiring to fuse box BUT with a battery pack, you will never be draining your car battery and putting wear on it.

nice

Hi, is the rear camera cable running on the top edge would be blocking the side curtain airbag?

I'm confused where to put the vcc fuse, please tell me where it should be.. thank you

Thanks for the video, I'm learning to do the same for my Nissan X-trail 2023. for the rear camera, could you pass the wires though the cables bundle that goes from the cargo door to the roof? or would that be very difficult to achieve without doing some damage to the plastic components there?

@dial2fast

10 ай бұрын

You can run the wire through the factory wire loom between the headliner and the hatch, but it's really not worth the trouble (in my opinion). Sometimes dashcam die and you have replace it and sometimes you upgrade it. The removal and reinstall time you spend to hide one wire is not necessary. The only time you need to do it is if you are mounting the rear camera outside the vehicle. If you want to see how it's done, you can watch one of my other video: kzread.info/dash/bejne/oqxmzJZvnceclZs.htmlsi=jLV0VP_qBKdOEa7f

Really nice video! I will have an nissan rogue and your videos has been really informative! Are you planning to put fog lights to it.? My rogue doesn't come it but i found i few ones on eBay that i would like to install!? What do you think

@dial2fast

Жыл бұрын

I have looked at those fog lights on eBay. The price is affordable. But to install the fog light, the front grill and bumper need to come off. I might get it when the weather is cooler to do the install.

@juanseijo21

Жыл бұрын

@@dial2fast awesome looking forward for that how to video! do you have any link or suggestion ? I trying to find one that comes with a "kind of original" switch to install in empty slot on the cabin

I got Thinkware installed on my Rogue 2020 but my liftgate does not open now. Did you face this issue? If not what might be going wrong?

Does this model Nissan use the accessory power pigtail like the '22 and '23 Frontier? It's a pigtail you purchase from Nissan that plugs into a harness under the kick panels (either side or both with two pigtails). It has quite a few circuits you can plug into including a B+, IGN+, ACC, Bat Saver, RF/LF/Rear doors circuits, etc. When I installed a new mirror and dash cam into my Frontier that pigtail made it easy and, they are all fused circuits from the factory.

@dial2fast

Жыл бұрын

The Nissan Rogue does have the factory accessory plug. You just have to be careful with how much current the accessories draw so you don't overload the factory circuit.

I think you can do a better job for the wire-routing of the rear camera. I put my wire thru the two grommet and drilled a small hole in the small plastic rear panel to let the wire came out.

Thank you so much for this video! I'm about to install mine for a Viofo A129 pro duo with the same battery. But mine came with an online power cut-off select on the output wire going to the dash cam. Is that normal? If so, what voltage should I set it on?

@dial2fast

8 ай бұрын

I think you are referring to your A129 hardwire cable having the cutoff voltage protection circuit. If you are installing a dedicated dashcam battery to power the parking mode, then you can set it to the lowest voltage setting.

@turborsx5740

8 ай бұрын

@dial2fast thank you for your reply, yes I'm installing a dedicated dash cam battery for it. I was just making sure I got the right wiring they provided. Because the only time I used that voltage cut-off switch is when I had my car battery run my dash cam

We have the exact same car and I am trying to do the same thing as you did. Now I want to know where you got that Heat blocking film?

@dial2fast

11 ай бұрын

The heat blocking film came with this particular dashcam. If you watch the dashcam review video, you will see that. Also purchasing link in the video description.

Great video! May I ask why you didn't use Thinkware U3000 cameras and the iVolt Xtra battery by Thinkware? i am looking to buy a similar system for my truck.

@dial2fast

2 ай бұрын

There are many good options when it comes to dashcam and battery pack. This happen to the model I chose for this install.

Were the micro fuse taps sold separately or did they come with the battery pack?

@dial2fast

Жыл бұрын

The seller includes one fuse tap with purchase of each battery pack.

I need your help please. I have a 2020 hyundai santa fe and cig 12v fuses are under the hood and i don’t want to go through the firewall to install a blackvue power magic B124x. There are fuses under the dash that have accessories that my car isn’t equipped with. 25A rear seat heater and 30A power seat switch. Is it safe to use either of these so long as they don’t have constant power or do these fuses have too high Amperage? If so can should i use a 15A or 20A in the second space of the fuse tap? thank you for your help.

@dial2fast

Ай бұрын

You typically don't need to run ignition power from engine to inside of car. You can get the ignition power from the fuse box, but with some modern cars, those unused circuits might not be activated via the BCM computer. That's why you have to test it with a multimeter to be sure. You mentioned power seat fuse, this is usually constant 12v. The seat heater fuse should work as it is ignition 12V. The higher amperage is perfectly fine to use. You just have to put your own rated fuse in the top slot of the fuse tap. The fuse you use just need to be higher rating that the rated current of your device. Meaning if the battery pack consumes 7A max, you can use a 10A or 15A fuse. These are all fast blow fuses.

@nemrac72k

Ай бұрын

Thank you for your help 🙏🏻

i have an AC to usb and hook it up to my battery pack. less than half the cost of the Powercell