Another great video! Nice to see the fender pulled for this job. I installed mine with the fender on but if I ever do another I'm going this route, or at least loosening the fender for it. I used a bit of sealant around the plastic elbow that mounts to the snorkel itself before I clamped it down. The bracket and hardware for the a-pillar worked fine for my install as I was able to get creative making the correct holes(square if I remember correctly?). Used a bit of clear sealant there too. Airflow is the only one made for the N50 Xterras. There is an R51 Pathfinder snorkel that will work with some modification. Far less expensive too haha. On a side note, I've noticed my intake air temps have dropped quite a bit and my air filter stays way cleaner after spending time in the dust. Well worth it.

I have that same snorkel for the A piller part I bolted to one hole and did not drill into the piller I used 3m tape and it’s been doing great

@Rythecarguy

10 ай бұрын

Oh. That's a fantastic idea. I have double sided gorilla tape. It's a perfect application for that. Thank you!

Looks like you need more Brennivin...lol

@Rythecarguy

10 ай бұрын

Haha tell me about it. And I need to fly back to Iceland to get it.

Awesome video!! Sucks that the only brand making Xterra Snorkels couldn't get the fitment right every time. Love the adjustments. Thanks for sharing

Good job Ry ! as for the pillar support what I did when I installed my snorkel I used this funny things called ( Hillman 1/4-in x 20 Brass Well Nut / 18 Pairs M4 M5 M6 Neoprene Well Nuts with Stainless Steel Screw ) they can be found at lowes or amazing.. worked great as they are rubber with nut inside I did not had to seal the hole on the pillar and it very secured P.S also the pillar bracket you need to flip upside donw.. )) 2 holes for pillar 1 hole for snorkel

@shooofly6580

10 ай бұрын

I watched your snorkel install on your channel, found it very helpful and the bracket fasteners a great option - thank you!

@DIY_AUTO_PHOTO

10 ай бұрын

@@shooofly6580 Thank you for watching as well ! and glad it was helpful!

Great timing - I ordered my snorkel end of August and received it Friday Sept 29th, just in time to watch your video. Found removing the fender made the process much smoother than expected - thank you! Also, as far as the bracket for upper support, I used mine by fastening the side with the two holes to the pillar and the slotted hole side to the snorkel, lining it up with one of the two captured brass nuts. I have a Volant intake and purchased the adapter which needed a little cutting and grinding to fit but other than than, I love the way it looks and that the air is coming from a better spot. Thanks again for your excellent videos (VK swap in the future)!

Great video as always Ry. Your funny and sarcastic comments while you’re working crack me up. I hope that’s not the only snorkel brand that fits our Xterra‘s, but I’ll figure that out when I buy one soon.

@Rythecarguy

10 ай бұрын

Haha thanks. Based on what I'm seeing in other comments this one might be the only option.

By the way, you should do a video about your recording setup and equipment. You've always got good quality

@Rythecarguy

10 ай бұрын

Oh thank you I have fine tuned it over the years and I'm pretty happy with it. Lighting could use some more work but that's always the case. 💪🏻

Looks great! Nice job

@Rythecarguy

10 ай бұрын

Thanks! 💪🏻💪🏻

That's awesome man 😊

@Rythecarguy

10 ай бұрын

Thanks 😁

I need you to stop... I already decided I don't need a snorkel just to look cool. Now you've dug this inner debate back up again

@Rythecarguy

10 ай бұрын

😂 but but... just look at it. 🥺

Love the shirt lol. I gotta get one of those

This was a good one lol.. thanks!! Subbed

@Rythecarguy

7 ай бұрын

Thanks for the sub!

I think the snorkel is not for water but for fresh air with lest dust if out in that kind of terrain.

@Rythecarguy

10 ай бұрын

Oh for sure. It's really for all that. Avoiding getting anything you don't want into your intake.

I just purchased these plates from the dealership..I will get the gas tank one as well. I ordered the bolts as well. Thanks for the video

@Rythecarguy

4 ай бұрын

How much is the gas tank one. I'm interested

@waynebeck7801

4 ай бұрын

I posted on the wrong video 😮 the gas tank skid plate is over 500 Cdn. So no to that.

Nice bonus DIY on fender removal too.

@Rythecarguy

10 ай бұрын

Hell yea!!

The forums show the bracket's double hole side bolted to the a-pillar and the "sliding" single hole attaching to the top snorkel hole. That makes sense since a single bolt on the a-pillar would tend to rotate over time and scratch things up. I guess the snorkel was made for other cars as well where the lower snorkel hole would be used instead.

@Rythecarguy

10 ай бұрын

Yea I realized that. Thank you, having the two recessed nuts really threw me off. I ended up using double sided tape on the pillar and the highest nut.

They are basically the only brand that makes a snorkel for the Xterra

@Rythecarguy

10 ай бұрын

Bummer.

could a "snorkle" be made to run under the fender and up the roof support making it mostly invisable? or is there no empty space?

Mr @rythecarguy, I have problems in 2006 Nissan Xterra off-road, I need your advice boss

Do you have to take the fender off ?

common misconception is that a snorkel is for water crossings only... while YES if you are going to do water crossings' the snork is a must but primarily controlling dust intake to the airbox is number one reason to add one, as stock air intake pulls air from the wheel well and if you drive on dirt roads at all you are just sucking down all that dust into your filter box that the tire kicks up and the snork is up high away from the dust cloud grabbing clean(er) air

@Rythecarguy

3 ай бұрын

👍🏻

@rythecarguy boss super cool, super nice, super beautiful, May ask you about the snorkel where did bought it please I wanted to purchase also for my XTERRA

@shooofly6580

10 ай бұрын

Not to be a buttinski, but when I ordered mine I found Offroad Gorilla had the best price. However, other vendors might ship it quicker as mine took a month to come in.

@arzibanez3924

10 ай бұрын

Thank you @shooofly6580

what kind/size tires are you running there?

@Rythecarguy

10 ай бұрын

285/75/16 and they are Americus AT/R's. quietest ATs I have ever driven. Gunna ride them off road soon to see how they preform.

Awesome! What does 8 ball mean here?

@Rythecarguy

2 ай бұрын

Thanks man. 8ball is its name. I asked the viewers to help me name it. 8 ball is fun because it's black and has a V8! 💪🏻

@richaneesh

2 ай бұрын

@Rythecarguy alirght! I was wondering what I missed hehe

Yo what size tire is that. About to go for bigger tires on my pathfinder.

@Rythecarguy

10 ай бұрын

285/75-16 love them.

@PYROtheNomad

10 ай бұрын

How were you able to find someone to install them? All my local shops say they are to big for the stock 16s but I’ve seen so many others run them so I know that’s not true

@Rythecarguy

10 ай бұрын

@@PYROtheNomad They are such babies. I bought mine from Duncan at Nissan Parts Puller and they were already on the rims and I just installed them myself. I know it's a pain but if you just throw your X on jack stands, bring in just the rims and tires and tell them to put the new tires on them LOL. They will mount and balance and you just put them on yourself.

@PYROtheNomad

10 ай бұрын

@@Rythecarguy ah ok that’s perfect. I guess that’s what I’ll have to do. I was actually looking at that exact tire size too. They look great on your X so they must look good on a lifted Pathfinder

@Rythecarguy

10 ай бұрын

@@PYROtheNomad oh hell yea. They are gunna look sick.

wow I actually got Unsubscribed from your channel WTF!!! that's the first one for me that i have noticed weird. I always hear channels talking about it happening but did not believe it as i never saw it happen but now i do... confirmed KZread is actually randomly unsubing..... I've been subscribed and watching your videos since the how to adjust the ebrake video from 8 years ago and all of a sudden no longer sub'ed... well +1 re subbing

@Rythecarguy

3 ай бұрын

Thanks for letting me know. That's insane! Welcome back.

A Pillar use rivnuts

@Rythecarguy

3 ай бұрын

Ahhhh never!! Can't drill into the body. 😬

@mr_e_mc2

3 ай бұрын

@@Rythecarguy YOU CAN DO IT!!!!!!.... In Rob Schneider voice, But yeah realistically I can see where the drilling could be hard to convince yourself to do, and in my personal experience is that all the workarounds to avoid drilling usually leads to a lot more work trying options that sacrifice something eventually winding up not working to finally giving up and then drilling the holes any way and asking myself why i didnt just do that in the first place. 😜

@JustinForAnAdventure

2 ай бұрын

@@Rythecarguy what did you end up doing to attach to the a pillar? I just installed the snorkel myself and regret not drilling the a pillar before installing because I'm not taking it off now haha. I'm using the bracket and some 3M tape as a temporary solution.