Thanks for videos man! I learned more in your two 5 minute videos than I did in several of the “more advanced” tuners 30 min videos!! I just subscribed, looking for to more of your “to the point” vids

@TheDrivewayEngineer

3 жыл бұрын

Thank you!

Simple to the point, always helpful!!

omfg dude your a life saver just came y truck and couldn't even make it tune o to professionally tune it thank you very very much

Awesome video man ! Thanks for the help . Straight to the point .

@notbuyingit8047

Жыл бұрын

Glad you posted this thanks. I just dropped Truck norris in my 5.3 taHoe and am about to run this as a base tune.

Thank you Did exactly what you said car turned right on idled

Thanks buddy, simple enough. 👍👍

Made it easy to understand! Thanks!

@TheDrivewayEngineer

3 жыл бұрын

Glad it helped!

Fantastic video man!

@TheDrivewayEngineer

Жыл бұрын

Glad you enjoyed it!

Thanks, helped me out.

Appreciate the knowledge

Put a thermostat in my 07 g6 today burp and burp then vapor locked it after 2 hours of scrolling how to fix it was one little bitty bolt and fixed all day job jr can you use this for a 4.3 I'm camming mine porting and heavy spring but I'll need a tune not finding much have not ordered a cam just researching

Great information

@TheDrivewayEngineer

2 жыл бұрын

Glad it was helpful!

does this also apply if you need to do engine break in or if you have a manual trans?

I have a 00 Sierra with a 5.3, 7875 Turbo, Hunter tuned injectors, No MAF. Did a speed density tune on it but when I turn the upstream O2's on it falls on it's face and won't go over 40 mph. Any ideas?

@TheDrivewayEngineer

4 жыл бұрын

Not without looking at a log

HEY JR, do the mild cams like Elgin E 1840 P that just drop in with no springs, seats, lifters or convertor needed still need a tuning upgrade?

@TheDrivewayEngineer

Жыл бұрын

That cam doesn't drop in with no springs or converter lol

I had an unrelated issue that I needed help with....I was hoping you could help. I have a Silverado RCSB with6.0 with summit turbo cam and gen 2 VS 7875. Full 4" exhaust and 3" cold side with FMIC. CHeap Chinese wastegate and BOV, and hot side from amazon that you showed in a video recently. So the problem is I can't get past 9-10lbs boost...even with wastegate boost reference line disconnected from boost controller. The VS gen 2 should be able to supply a lot more boost right? Any ideas? I have a crossover pipe on the wastegate so I can't really tell if/when it opens. Thanks in advance! ANd thanks for posting the videos they helped a bunch throughout the build!

@TheDrivewayEngineer

4 жыл бұрын

Cheap Chinese wastegates are known to not be super accurate. What spring is in it? And is it clear of debris and nonsense?

@davidnapierkowski5075

4 жыл бұрын

It was assembled poorly, loose screws and pinched diaphragm. I totally forgot to check it before I installed it. THis happened once before....THanks!

If i drop in a mild truck cam will i need to tune it to get it to run? Its my daily driver so im going for as little down time as possible. Do you have a secret budget cam company? I got my eye on a summit racing cam but its knocking on 300$...

@TheDrivewayEngineer

4 жыл бұрын

They need tunes. Some will run, some won't. There would be no point to this video if they ran perfectly lol.

i was trying to follow the last video you posted about this and coudnt find main ve primary... is that cause i was under advance user istead of base or because i was trying to tune a E38 pcm?

@TheDrivewayEngineer

4 жыл бұрын

It's because it was a E38, it uses virtual VE, it's under the Speed Density tab

@brianschollenberg8907

4 жыл бұрын

@@TheDrivewayEngineer thankyou

Jr, what brand or who makes the headers you running on your c10?

@TheDrivewayEngineer

4 жыл бұрын

Speed Engineering

@marcusmumphrey6995

4 жыл бұрын

Thanks

In your opinion what's the best tune for a 6.0 with a sloppy stage 2 cam to get the best idle lope sound.

Nice ❤

Will this method be sufficient for a first start up and cam break-in to be able to drive to the dyno?

@TheDrivewayEngineer

Жыл бұрын

You don't break in roller cams

@christophershafer5615

Жыл бұрын

@@TheDrivewayEngineer Thank you for the information. I am a first timer and am also watching the GRG channel.

If I’m running rich how would I adjust the table?

@TheDrivewayEngineer

Жыл бұрын

Lower it. 100 is 100% of what the injectors can do, 0 is 0, so if it's at 30 where you're rich, drop it to 28 and try again

@louisevans2000

Жыл бұрын

@@TheDrivewayEngineer thank you sir

thanks

How do I buy this program

@TheDrivewayEngineer

3 ай бұрын

It's available from Summit Racing, Jegs, a million resellers, or straight from HP Tuners

I've done it all.. it still won't start up and run. 6.0 ls3 stage 4cam

@michaelbraddy2463

Жыл бұрын

You might have to bump up the fuel or idle rpm

@iceship1

Жыл бұрын

@@michaelbraddy2463 ok thanks.. I'm at 1200 RPM now, hope fuel does the trick.

@iceship1

9 ай бұрын

I finally had a little time to play with it.. will only start when pedaling the throttle.. so would that be not enough fuel.

why turn vats off or am i mistaken its vehical anti theft system right ?

@TheDrivewayEngineer

2 жыл бұрын

Because it won't start with it on.

@arealmaintenanceandrepairl1103

2 жыл бұрын

@@TheDrivewayEngineer oh ok I have an issue just did cam I’m able to get it idling and run but at idle I have no breaks vaccum is low… my cam is small truck Norris… how can I get my vac back