The only thing I would do different is, to print small test pieces, instead of waisting time and material of full prints.

@bestyoutubernonegraternumber1

Ай бұрын

What I would do is use a laser & do it in 1 minute instead of 17 hours. Use the right tool for the job. 3D printing has its place. This ain’t it.

@yzmotoxer807

27 күн бұрын

Waisting time? What, do you have a belt made out of wrist watches or something?

@defi5

25 күн бұрын

@@yzmotoxer807I like this comment

The correct answer was #2, upside down. What you saw were not layer lines, they were evidence that you need to calibrate your Z offset. There should NOT be space between lines on any layer, but most importantly the first layer.

gaps between extrusions on the first layer is something to rectify. Either your z offset is not right, or your extrusion rate is not right. With a perfect first layer, the bottom will pretty much always look better than the top, even with all the settings you used.

@daliasprints9798

28 күн бұрын

This is largely true, but without monotonic fill order, either will look bad.

Textured bed sheet, upside down, lower z offset so the squish will blend, and same bottom layer advice you used and it’ll look 10x better no ironing needed

Such thing always upside down. But needs perfect first layer. Love smooth pei for this

Thanks for the tip! I’ve been using cura for 2 years and never knew about the monotonic settings. This solves a lot of problems I’ve had to deal with

I've just started filament printing, and this tip is exactly what I've been looking for 😃

I bought an Infimech TX a couple of months ago. Guys, this thing is AWESOME. I'm getting rid of all my ender 3s. I'm no spokesman either. I'm FINALLY able to finish up on my 1:1 F-16 Cockpit for DCS and MSFS. SUPER Smooth prints. I literally slice and hit print. I walk away and it's done!!!!

I like you don't use music in your videos, thank you for that and for share the settings.

@VaderDadBuilds

8 күн бұрын

Thank you for watching!

Flip it upside-down, level your bed, lower your z offset just a little to make a squish and that's it. No need for such a waste of filament.

honestly it looks like you have some under extrusion going on, especially on the bottom layer example.

I appreciate the time you put into this video, especially with the number of times you reprinted the clock. A tip I can pass along to you is to flip the flip upside down, like you did in the video, but print it on the reverse (smooth) side of a glass bed. It will come out insanely flat and smooth

Subbed because your video was no-nonsense and gave a really good layout of what I was going to see, and saw exactly that. Perfect!

@VaderDadBuilds

Ай бұрын

Thank you! I appreciate that!

Bambu slicer has several adjustable parameters for ironing, one of which is Ironing Flow. It's default is 10% but I find 11-12% gives me a nearly perfect top layer.

@dominicpond

11 күн бұрын

The Bambu Printers print well enough where you rarely even see the lines without ironing, or at least not as bad as these prints

@jamiemacdonald436

10 күн бұрын

@@dominicpond True. I use ironing very infrequently.

I think you would benefit from using Orca slicer, an ABL decice to create a mesh before each print, and a PEY hologram sheet to print it upside down amd give the clock face a holographuc surface. Orca slicer has a lot of great calibration tools that are filamemt and machine specific. You can create a one layer print to perfect your Z offset value prior to running all the calibration prints

Monotonic simply means the head is traveling in the same direction for each extrusion move. It is interesting that Cura does this more orderly but that isn't a requirement for monotonic. Good video, I think I need this clock for my theater.

On the top layer use a concentric surface pattern for this round object. Otherwise try using a Hilbert curve if using Orca slicer. These tend to give a better top look, imho.

Whenever he says "layer lines" he means "print lines". "layer lines" are the lines between each layer, which run vertically throughout the print, not across the top layer of the print (which is a single layer)

Good video, i like your style, no nonsense, you get straight to it and show us your full process with clear and concise explanation. Good work. First video I've watched on your channel, I'll be back for more 😊

@VaderDadBuilds

22 күн бұрын

Thank you! Hope you enjoy the other videos as well.

@orionmurphy2525

8 күн бұрын

Yes str8 to the point , no nonstop talking for the first half of the video 😂 thank you @vaderdadbuilds

Juat tune your first layer properly and print up side down. It will be perfect

@daliasprints9798

28 күн бұрын

That works here, although I find the ugliness of non monotonic is often visible on the bottom layer too. And in general, not all prints admit flipping, so this is a useful tip for his audience.

@Vez3D

28 күн бұрын

@daliasprints9798 true true. My comment was written too quick from my phone and I must admit after reading it sounded a bit rude. Apologies

@VaderDadBuilds

28 күн бұрын

All good, wasn't rude to me. Plus these comments help me make a better video next time.😀

@VaderDadBuilds

28 күн бұрын

Thank you. Yea, I used the wrong file to show what I was trying to show. Lol

I suggest looking into patterned and mirror finish printing plates, and try the face down option (2) again with the plate designed to give a specific finish. (use slightly higher than normal heat to really let the pattern melt into that first layer( like an extra 5c))

Printing face down on glass with a light coating of hairspray does it for me, almost perfect surface quality! Also need just the right z offset to avoid gaps.

You had it right when you flipped it upside down, but needed to dial in your settings for the first layer. Dialing in the top layer is good when you need a good top and bottom layer, but this could have been just a good 1st layer.

I would use some of the fancy plates you can get with patterns in them one of the patterns is like carbon fibre which would look good, some of the less obvious plate patterns would also be good. They are generally smooth in texture so a good first layer would give a nice smooth surface with like a printed pattern visual not textured.

1) Print upside down (and use a build plate with a nice texture) 2) Decrease first layer line width. 0.3 works just fine with stickier PLA, 0.35 works with most materials.You need to watch the first layer, if it rips or lifts, then either increase the width by a bit or use a lower first layer height (0.12mm instead of 0.2mm for example). 3) Increase first layer flow rate to 105-110% 4) Use a different first layer infill pattern that doesn't leave gaps (this depends on geometry, I don't change it for most models). Concentric sometimes works better Ironing sucks, leaves the surface too shiny, tends to clog the nozzle on some printers and can leave some nasty lines sometimes.

i think, there are some improvements. try min. 4 top layers, because the infill is peaking through. put it upside down, like you did, lower the Z a half layerheigh, put a 0.3 bottom layer with 105 to 110 extrusion. is it possible, that you dont have a abl ? because of the big heigh differenzes. i use 4 bottom and 5 top layer to vanish the infill peak through and enough stability its a great idea

@darrennew8211

Ай бұрын

That was my take. The lines are caused to a large extent by the top layer sagging.

Smooth PEI or garolite/g10/fr4 and printing it upside down is always the solution you should go for if you want a smooth or even mirror-like first layer since it saves time and significant amounts of effort versus ironing. Just gotta dial in Z-offset to not get those awkward gaps

Concentric top layer may look great since it is a clock.

for smt like this print flipping the model and using a powdered bed is perfect, u dont see any print lines. For other models ironing is good but needs to be calibrated perfectly

Great tips..

for a while i couldn't figure out why i wasn't getting perfect ironing anymore.. I installed a BL touch. this basically makes the whole print carry the wavy offset of the bed mesh level though-out the whole print. I put Fade_start: 0.2, Fade_end:1 into my Bed_mesh in my Klipper printer.cfg file to fix the problem. Beautiful top layers, even without ironing.. but of course ironing is better. I also have gone full OCD and trammed the printer like its a machining mill lol. So no matter the direction the nozzle is doing the top layer it looks exactly the same My bed mesh goes from -0.1350 to 0.2400, carborundum glass bed with thick aluminum heat plate. I print up to 115c bed temps, the glass doesn't take long to start warping and finding a "home" to where it settles

Although I appreciate the attempt, this could be just 1 or 2 steps: 1. Correct Z height 2. Adjust (first layer) flow/extrusion. A perfect first layer won’t have any layer lines and will always be better than an ironed top layer

In my experience if I see layer lines on the bottom layer it means I'm under extruding, first layer temp too low, or bed too cold. Mostly extrusion. My prints always come off with a perfectly consistent face, occasionally a tiny little knot where the plastic pulled up a quarter millimeter.

Thank you amazing

Some slicer you can change the top layer to 0.1 for finer finish if the adaptive layer height was not doing the job. For something like this I just have no bottom layer to speed things up.

Did you use Z-hop for the top layer?

thank you

Simply print the file facedown on the print bed, the fact that your first layer is a bit crappy isn't a good reason to abandon this approach, I can fairly easily get glass smooth glossy prints using this approach.

If you do upside down, over extrude the bottom layer. Ie kind of like elephants foot. Also, people have been using special surfaces to get holographic style reflections. P-flat sheets I believe they are called

One time I need same things I want hide top layer....I have just flip the piece and start with first layer like 0.08 or 0.1 I don't rememb good but if you have good first layer try this flip the piece and put 0.08/0.1 in first layer

I use PLA+ and the down face is as smooth as a whistle when I use my smooth bed, or has a nice random pattern if I use my patterned bed. My guess is you need to set your extruder temperature slightly higher.

@486veR

Ай бұрын

Do the same thing and turned off the fan and the plate on 10c higher than remmonded

Almost all of this issues already fixed in various latest patches of orca slicer.

You need to print it upside down on a textured plate and use a .2mm first layer

flip it over, face down.... use a smooth heatbed

Thats pretty cool. Though i would probably just prime the crap out of it and light sand. Im definitely going to try the trick for the more curvy prints. And gotta say, that clock would look pretty sweet with a backlight to bring out the detail.

@VaderDadBuilds

28 күн бұрын

Thank you. I was thinking about adding that backlight too!

@blackc1479

28 күн бұрын

@@VaderDadBuilds right on.

hey try setting the exposure of your camera down, looks like the video I'd clipping, reach out if you need help

Try slicing it with Archimedean on the top layer. Way better for objects that are circular

Man, this is a simple upside down print. Use the same settings you would with a coaster. The mono top finish was a good insight. Avoid ironing where u can...adds way too much time.

Upside down its the way, but you need to adjust a perfect first layer, looking your prints i think you need to adjust max flow, a perfect calibrated bed and z-hop.

I think you could have saved yourself a lot of time with a smaller project. 👍

hmm… why not use regular iron on metal sheet which cover entire object?

OR you could get a PEY bed, print upside down and have a perfectly smooth (or texture of your choice PEY depending) front surface.

Great video what printer are you using

@VaderDadBuilds

Ай бұрын

Thank you! I'm using an Ender 3 Max Neo

Next time do face down with a mirror finish build plate

Where are you getting the clock pieces at a reasonable price? All the ones I have found are absurdly expensive.

@VaderDadBuilds

Ай бұрын

I got a set of 2 for $8 on amazon. That is the best price I found, unless to buy more at a time.

It's so utterly stupid that monotonic isn't default. Cura used to always do monotonic, but added "optimized" order a few years go, and only added the option to go back after enough people complained... 🤦

Looks like too few top layers. We're seeing where the support walls are.

Upside down should be much better if only you will adjust flow rate, z-offset and Esteps. Your first layer looks a bit underextruded...

Eighteen _Fuckin' _*_Hours?!_* 😱 Had to slap this onto my Slicers Build Plate just for the shits and giggles and even with Ironing enabled ( adding another 2h20min ) it would still only take 4h40min!!! Toss whatever Joke of a 3D Printer you have and get yourself a real Machine! This is outrageous even just hearing about yet alone experiencing it in this day and age of affordable _fast_ 3D Printers 💢

In your case all you need to do is print it upside down and actually tune your z offset. That looks too far.

@neonZXk

Ай бұрын

Yeah I was going to say the same thing. This is just a simple flip.

17 hrs? Is bambu really that much faster lol.

Your face down print looks like your extrusion is too low or your z-offset is too far from the plate. My face down prints are much more even with a proper tuned first layer. But ultimately, for 2d silhouettes like this, I feel a laser cutter and acrylic sheet is a far superior option. If this is for small business commercial production, an investment in a $500-900usd laser wouldn’t be unreasonable

@senseisecurityschool9337

Ай бұрын

That's a good point. And it doesn't even have to cost $500-$900. If you already have a 3D printer, you can get a laser head for $150. That's reasonable for a hobbyist. Particularly for a hobbyist who may have upgraded to a different printer, so they have a spare printer sitting there.

to see if the bottom layer has printed better than the top you could ve just flipped the thing lol

upside down, set first layer width to 0.35 and infill overlap to 30%. Thank me later

@3DEMS.

7 күн бұрын

ohh, and if you use a well calibrated machine like mk4, much better

I don't like adaptive layers. It's slow and does odd things.

It's waaay more practical to simply print it upside down, with a thicker first layer, than sand it after printing. There is no point in the "no sanding" part of the title. Sanding takes only a few minutes, while printing with "advanced options" makes printing much longer, much more prone to error and to wasting material. This is the kind of "tutorial" that makes me think about that joke of leting the stove always on fire just to avoid using matches to light it up.

Уважаемый, просто переверни деталь на сторону лицевой на стол и буквы смени направление. И будет тебе счастье!!!! Сейчас есть красивые столы с офигенным покрытием и не нужен этот геморрой😊 удачи в печати

18 hours? 😭 Just cut it out of sheet metal

11 hours for that? Are you kidding me. A modern 3-D printer can do that in about 30 minutes.

Who uses cura in 2024?

@aphixe

13 күн бұрын

What do you use. Prusaslicer

@KIDC0SM0S

9 сағат бұрын

I do

Step 1: throw away Cura and use orca slicer.

@BluFirefox101

26 күн бұрын

real

@yt-sweety

24 күн бұрын

fr

I dont know man, you were just underextruding

Such a waste of time.

What I would fix the biggest issue first, trash the Ender and buy a better printer, then you wouldn't have any of these issues and it would print about twice as fast

Man, you wasted my time for nithing. That all old information and already writed in slicer settings.

Lol spends all that time showing us the poor finish layers but then when he gets to step 5 I blinked and missed the view to be able to compare ha ha. So still crap then