amazingly, this actually helped 2 years after posting. thanks bro!

Thank you so much, I was annoyed for like a whole week because I couldn’t play assetto corsa without my sim racing setup working properly.

@floorit27

2 жыл бұрын

The pain of non working controls.

Beautiful! Picked one up used from marketplace and the clutch was dead and break only worked half way... A vacuum, hot glue, and WD-40 and it's running great with full response from the clutch now. Next it's the loose steering wheel but I'm able to drive properly now!

@floorit27

Жыл бұрын

Awesome!

i know you have probably seen this a lot but thanks yo i'm glad that there is someone out there that has a solution to this problem.

@floorit27

2 жыл бұрын

I enjoy it every time I see it!

I didnt try this yet, but even if it doesn't work, your explanation was clutch. I never understood what the problem is.

You're awesome man. A little WD-40 on the springs and some hot glue later, and mine actually works better now than it did when I bought it. Thanks.

@floorit27

Жыл бұрын

Really awesome to hear. Every time!

you save my life，omg i just sad like 3 day already，because i play horizon 5 and get down about this problem。 you derserve my follow and like， thx man。sry about my 6 years old broken english have a nice day！

@floorit27

2 жыл бұрын

Easy to read, you're fine! I'm happy the video helped!

Thanks alot brother. I fixed mine

Thanks for this great video man, I was about to tore my savings by buying a logitech wheel due to issues on my pxn v9 pedals. the gas pedal is in 30% and the clutch at 60% all the time. Hope I can fix it with this procedure

@floorit27

2 жыл бұрын

If not it might be worth a shot reaching out to them, support@e-pxn.com

@vinyldash2333

Жыл бұрын

An issue my accelerator had is the potentiometer wasn't installed correctly to begin with, so I'd only be getting 85-90% at best. I did some fiddling with the angle it was sitting at and now it works just fine.

hi bro my clutch is not working when i tried it in the app its not detecting any signal

I have a question about the PX V9 because I bought it and a couple months later everything works but my pedals and shifter are not responding in game but when I test it in the app they work how do I fix this?

this is the exact same problem my pedals have, i'll try your solution and hopefully i don't have to buy a new pedal set 👍 thanks a lot

@floorit27

Жыл бұрын

So far I've heard good news from 99% of people with this fix. Hopefully it works for you.

@timhan8667

Жыл бұрын

@@floorit27 I didn't feel like buying a hot glue gun. all i did was put a paper towel between the potentiometer and the plastic casing, so that it would prevent movement. this fixed the issue.

Oh my God,thank you so much

Backstory, I know very little of sim racing set ups and bought this wheel about 3 months ago. Everything works fine after fixing this problem, but like you said in some other comments, it's probably bound to happen again. Before that happens, I was gonna look into buying one of the better pedal sets, something like the clubsport or something similar. My question is, if I find pedals that use the same output as the PXN-v9 pedals, would I be able to theoretically plug them in and play keeping the original V9 Wheel + Shifter? Ofc app compatibility afterwards may be questionable maybe. I would like to know for sure before I spend 300 on a pedal set I can't use yet, and I can't find anything on the internet about it.

@floorit27

Жыл бұрын

On PC I would imagine if you had pedals that connected as a separate device, it's likely they will work in a way, just like your controller and mouse and keyboard all work at the same time. I can't remember who, but one of my followers was going to make their own pedals. I've never heard how it turned out. As for what plugs into the controller as a direct replacement, as long as it sends the same data the original potentiometers send(or have the same potentiometer), it should work. You could use the original wire to make a pigtail for the connection to the controller. It would most likely have to be homemade if connecting directly to the controller. The software for the controller limits that. Best case scenario is the game you want to play allows the simultaneous input of new pedals and the og shifter and at the same time. If the fix doesn't work for you, I think the product might just not be up to par with your expectations. I haven't tested many other products, so I don't have other recommendations.

Same trouble thanks for information

@floorit27

Жыл бұрын

Glad it helped!

I’m 100th subscriber let’s gooo

Hey man what's up every time I glue the thing it works and it gets better and it fixes itself but after some use after like 15 minutes 20 minutes it goes back to fluctuating so did that happen to you?

I’m was having an issue that this video fixed so thank for that but I’ve been having this other issue where the pedal doesn’t start responding until it’s pushed down a little far so if you have a solution for that that would be amazing

@floorit27

Жыл бұрын

That is the calibration I mentioned. Have you done the calibration? Glad it works better. Keep working at it.

you're a legend man, thank you🤍

@floorit27

2 жыл бұрын

Glad to help!

You my hero

thank you

Mine says that I'm pressing down on it even though I'm not would this problem be fixed by doing this?

can we have a tutorial for the steering wobbling?

Anyone know what is wrong with mine the acceleration works fine but the clutch and brake are set as the same pedal and I can use the shifter any tips for it I'm playing beam ng drive btw

Thanks for the video . I bought one of these just a month or two ago and used it less then 10 times for ETS 2, never used it roughly and put it aside until yesterday when I plugged it in I noticed that my acceleration was less and less going to a dead stop, then it started working again ,then same thing happened. I was struggling to go at 10 km/h with pedal to the floor. The brake is fine and I haven't used the clutch or gear shifter so far since I bought it. I'm hoping this video solves the problem but pissed that there is a problem in the first place especially since its hardly ever been used. And I don't think mine is a dirt issue as after its used I put it aside and cover it with a cloth to protect it from dust. Any ideas what the problem could be? ......ok Its the next day now I opened it up and did as you did in the video and it seems fine now. I added a little glue to the top sides of the little circuit to hold it down better .Just gave it a test run on an ETS 2 delivery run and everything is ok. Thumbs up to you pal.

@floorit27

2 жыл бұрын

Good work!

Hello. I know that it worked for some people, but my acceleration pedal became worse. I could throttle up to 100%, but going there from 0% became more rough. Are there possible things I may have done wrong?

@floorit27

Жыл бұрын

If you're sure the potentiometers are not moving, then the next step would be the calibration. It sounds like now that you have reseated it, the potentiometer has a new position. Calibration will set what position is 0 and what is max. Let me know if that works!

Clutch pedal went out. Turns out the Clutch chip cant disengage and stays around 60 - 69% engaged when not touched. However it works fine when being pushed. Just wont disengage. i think the chip is the problem

@floorit27

2 жыл бұрын

Take it out and spin it outside of the pedal and see what you get. I am talking to them now about getting new pedals because A. I want to see if they send me something half decent and B I'll have extra parts. The potentiometer's are cheap from what I hear but that should also mean cheap replacement... They are accessible enough. But I'm almost at the point of taking this whole video back and saying talk to the manufacturer, as its almost a luck of the draw thing with this type of design.

mine doesn't work on Xinput since it's been used with x360ce mapping, but all buttons on Dinput work, please provide a solution...

@floorit27

2 жыл бұрын

Switch the steering wheel mode. It starts at an Xbox controller mode. Once you switch it, it will be the PC input version. Hopefully I understoof the issue correctly.

I did this and it helped A LOT but whenever I press the gas in game it breaks and when I press the brake it still brakes and the clutch works perfect any way I can fix it?

@floorit27

Жыл бұрын

Could be on the wrong mode. Try switching the mode

all of my pedals are jacked up and Ive had no issues since I got it for christmas. My brake is the only one that slightly works. Anything I can do to fix them?

@floorit27

2 жыл бұрын

This sounds like a wire issue! the main wire. Did they all get wack at once? Or kinda over time? The less likely answer if the issue didnt occur all at once is its dirty af, take it apart and get an "elecronic cleaner" spray and paper towels and go to town cleaning. Many people have issues because there are large gaps for dirt to get in. If they all went bad around the same time: Check the main cable coming out of the unit by taking it apart like in this video. Check it for obvious damage where it comes out. You likely won't see any though but you could see a kink in the wire. I would (not saying you techincally should) but I would then cut the wire an inch away from where it comes out of the sytem both on the inside and the outside cutting away any part of the wire that may have been bent too hard. Splice/solder the wires back with their respective pairs, tie a knot in the cable, and leave the knot inside the divice, as to prevent to cable from being pulled out of the unit.

@ryanebel3707

2 жыл бұрын

@@floorit27 over time. Me and my dad looked at in insides and took each potentiometer out and tested them without the pedal. The clutched died there but the others were the same. We put everything back together and I recalibrated them and they were fixed. Idk what it was but they are fixed now

For some reason my accelator is lagging I did a test with my controller accelerator and the controller accelerator was working better

@floorit27

2 жыл бұрын

I would take the potentiometer out and rotate it by hand and watch what it does.

Hey when I go into calibration and press the pedals I get no response at all only getting response from the steering wheel any idea what can be going on also my pedals are only break and gas

@floorit27

Жыл бұрын

try switching the mode

i checked my gas pedal and nothing was moving that shouldnt be moving. i cleaned it and calibrated it but this flickering problem is still there. pls help i dont know what to do.😮‍💨😕

@justinhammond2357

Жыл бұрын

OMG i just fixed it xD. the issue was that this electronic thing wasnt properly glued together and was kinda angeled🤣🤣

my white wire that is connected to accelerate pedal got cut is it game over for me ?

@_hugo_4143

11 ай бұрын

(Use trad french to english) il faut acheter de la pâte à souder et la chauffer avec le cable

I have a very annoying sound in them, I own a hori apex. The gas and the break. how do i fix that for no annoying sound more?

@floorit27

Жыл бұрын

I'd assume it's similar to these. A non conductive grease might help

I have the same steering wheel and a few days ago it stopped working because when I plug it into the computer (pc) in the application to connect it, it takes it as a play station, something that did not happen a few days ago, how can I solve it, does anyone know anything?

@floorit27

Жыл бұрын

Sounds like the mode changed if it things it's a Playstation controller. Try changing the mode! Sorry for the late reply.

You are real Kulibin. Your solver problem metod work! Are you cheenese worker?

I can’t get my petals to work how do you set it up when you first use it?

@floorit27

Жыл бұрын

Try using the mode button. Look for it in the quickstart guide, only one mode will work in each game or device normally

My acceleration is going to halfway and won’t go to max

I'm having troubles with connectability let's just say I'm playing BeamNG drive it will not boot up saying device not recognize and shut down the wheel

@floorit27

2 жыл бұрын

Wire issue is the first suspect. Do you have a different system you can test this on? If you do it can help determine if the wires are good or bad and go from there. As it could be a PC power save issue or USB issue. The software conflict would be resolved in Windows Device Manager. Try updating the drivers

Hey, when i hit the gas, it's doing another button and i don't know how to fix it. Do you have an advice?

@floorit27

2 жыл бұрын

Almost every game requires the secondary set of controls the controller comes with. The first input is like a legacy xbox input. If you hold the mode button I believe it is, for 3 seconds or so, it switches.

@floorit27

2 жыл бұрын

I looked it up, here ya go, page 5 www.e-pxn.com/sites/pxn/files/product/manual/pxn-v900.pdf

copied from other video: thanks, mine also works better after just blowing it myself using my mouth lol, but apparently my potentiometer at the acceletor/throttle paddle is loose so I just lay in a plastic wrap (MAMEE wrapper lol) in between and voila it works fine, but unscrewing all those screws are annoying af tho, in other words try inserting a plastic wrapper folded to give more thickness and tension on the potentiometer board, mine works like a charm after. be careful not to damage the circuit especialy the tiny resistor tho.

@floorit27

Жыл бұрын

This plastic wrap idea is great

Hey, is your clutch staying at 50% ? If so how would I fix it

@zazahorros9063

2 ай бұрын

Did you fix it ? I have the same problem in Forza games

@jvzrrr

2 ай бұрын

@@zazahorros9063 i fixed it in beam ng btu im not sure what to do on forza as i dont play the game

Спасибо,помогло

Uhm i think my sensor itself is broken, i have it alone and it doesnt work properly

@floorit27

2 жыл бұрын

Taking it out and spinning it, if its not moving or jumpy its probably toast.

When i driving certrain cars it keeps hitting the max rpm in all gear do you know how to.fix it ??

@floorit27

Жыл бұрын

It's probably only happening in certain cars because of the different transmissions+traction control. You should follow the video to take it apart and see if you can clean it first

@hasdevsingh6009

Жыл бұрын

@@floorit27 yo but in my assetto corsa my clutch is always half way compare to the throttle

@Frosty_yo

Жыл бұрын

@@hasdevsingh6009 PXN-V9's clutch is always set at 50%. You will have to modify the deadzone of the clutch in game to 50% to cancel it out

My pedals just completely broke in half :/

@floorit27

2 жыл бұрын

(my best tip at the end, got carried away typing) That sucks. This is really kinda cheap but the next steps up are far more money. Good for the money... On the bright side, if you're within a year you may be able to replace it! Contact them! On the other bright side, there are really cool ways to mend plastic. One of them is heating up metal rods like paperclips in the shape of stiches and meltng them into the plastic. This requires probably a bit of practice. I would get JB Weld quick set Epoxy. They have a 5 minute 2 part epoxy that hardens very well. Start with tiny bits and have the peices held together well and let them sit for hours. Then add a little more glue, slowly painting more and more on to add layers. Stuff dries harder than the plastic they use!

I have a problem with mine where the brake pedal works as the gas pedal but also the gas pedal works as a gas pedal

@ryansmith1136

2 жыл бұрын

And I’m on console

@supremeandy9840

2 жыл бұрын

Hold the "PROG" button for 3s and than the "OPTIONS" button maybe the Reset works on you

@floorit27

2 жыл бұрын

You do need to make sure the controller is in the right mode. There's a little quick start guide it comes with that details switching it so it has the proper inputs.

@floorit27

2 жыл бұрын

Sorry I looked it up for another comment so here, page 5 www.e-pxn.com/sites/pxn/files/product/manual/pxn-v900.pdf

anyone else not able to get the potentiometer back into place

@floorit27

Жыл бұрын

Any luck?

You save me

@floorit27

2 жыл бұрын

Yesss! This helped? Glad to hear

Hello brother i hope you reply back I got my pxn v9 working and i only use once My grandpa die and i didnt use my pxn for a week and now i try it my pedal aint working steering wheel and shifter working very well but the pedal didnt work this is almost brandnew can you help with this?

i just want to make the pedals more ferm

I can't to open the pedal cover

@floorit27

Жыл бұрын

Did you remove the rubber pads? They cover screws.

@user-xp2bx5nw2l

Жыл бұрын

@@floorit27 Yes, I removed it

do you have a FB page?

@floorit27

2 жыл бұрын

I got off FB more recently for the complications it presented to do fb youtube and twitch at the same time, and i never got viewers

My gas peda stopped working

@alexitoparte2

2 жыл бұрын

x2

@floorit27

2 жыл бұрын

Completely? If you are in warranty, see if you can get a replacement. I would personally look into getting a replacement potentiometer. You can test the potentiometer itself by removing it from the pedal and spinning it in your hand while watching the display from the link in the video description.

@floorit27

2 жыл бұрын

Sorry for the late reply guys, but like i said to FARMBOY, warranty, or soldering a new potentiometer.

@farmboy2823

2 жыл бұрын

@@floorit27 I bought it off of a buddy so no warranty

i am not doing allat!

the pxn v9 pedals is trash

@floorit27

2 жыл бұрын

For the money, id buy them again, but id probably buy a warranty if i didnt plan to fix them again. This is bound to happen again

@madlisankamodira5419

Жыл бұрын

This thngs is trash yeses