EaseUS Data Recovery Wizard will help you get your lost data back - bit.ly/3q5r2J6

@shortclipyn

2 жыл бұрын

please help me my keyboard usb thing doesn’t connect and to my pc and i checked the inside and it’s bent 😢 please tell me how to fix if u can thx 🙏

I owe my college degree to you. You saved my semester thank you so much.

@ElectronicsComputers

3 жыл бұрын

I'm glad I could help you!

This video just saved me from having a complete meltdown. Thank you!🙏🏾

@ElectronicsComputers

4 жыл бұрын

I'm glad I could help you!

Clear, concise, to the point. So many you tube poster's could learn alot from you. None of those bloody infuriating, two minute introductions, set in a "workshop" like most of the TV-show-host-wannabes, on here use.

@ElectronicsComputers

2 жыл бұрын

Thank you for the comment!

This guy has saved more people than he will ever know. Thank you so much I used the first method and transferred files in a very awkward position 😂😂

@ElectronicsComputers

2 жыл бұрын

Thank you for letting me know, I'm glad I could help you in that way.

I swear only 10 seconds into your video you have also just saved my life. I had important work on my usb which i absentmindedly did not make a backup and did not want to do again 🤦‍♀️🤦‍♀️🤦‍♀️ very much appreciated. Bless you guys!

@ElectronicsComputers

4 жыл бұрын

I'm glad I could help you!

Ditto what others said. Your instructions worked perfectly, and I was able to save all my data. A million thanks!!!

@ElectronicsComputers

3 жыл бұрын

Glad it helped!

I accessed files that I haven't been able to access in over 5 years. thank you so much!!

@ElectronicsComputers

4 жыл бұрын

Glad it helped!

Allow me to add my thanks for this fantastic video. Not only did you confirm what I thought was possible but without that wiring diagram I would have had no way of knowing which cable went with which pin on the circuit board. Short, sweet, and effective. Thanks so much!

@ElectronicsComputers

3 жыл бұрын

Glad it helped

I am so thankful for this video. I broke my flash drive and I thought I had to say goodbye to all my data. I called a few IT stores and they all quoted me over $400. Well after watching this video I decided to test my luck. The broken pieces on my flash driver were similar to the ones in this video. So I tried the option of aligning the broken pins to the connector. It took a few tries, but it lit up and I was able to hold it in place and retrieve all my data. Thanks for making this so simple. I hope someone else has the same luck I had!

@ElectronicsComputers

Жыл бұрын

I'm so glad I could help you!

Thank you so much you saved my son a lot pain and anxiety. His university notes and work notes were not backed up and he worried he had lost everything. With deepest appreciation.

@ElectronicsComputers

Жыл бұрын

I'm so glad I could help you, guys.

The soldering method works for me. I am so proud of myself now! Thank you!

@ElectronicsComputers

3 жыл бұрын

Good job! I'm happy to help!

You rock! Your wiring diagram and temp jumper idea with a USB cable saved us from losing a ton of crucial files my wife had only on 1 broken flash drive! I used your solder jumper method and it worked perfectly! All files are in 4 places now!

@ElectronicsComputers

Жыл бұрын

Excellent job! I'm happy to help!

omg all my coursework for school was one that usb stick and your video helped me save myslef from failing, thankyou so much :D

@ElectronicsComputers

4 жыл бұрын

I'm so glad I could help you!

you are an absolute gem! my dog knocked my macbook pro over damaging my lifelong Verbatim store and go companion, but your method brought it back long enough for me to clone it to a new one!!

@ElectronicsComputers

3 жыл бұрын

I'm glad I could help you!

Words cannot express how awesome this trick is using old cable. So many thanks.

@ElectronicsComputers

2 жыл бұрын

You are most welcome

Thank you! You helped me recover years of work, and saved me over $100. Great video!

@ElectronicsComputers

Жыл бұрын

I'm glad I could help you.

I just did this exact method you demonstrated to a bent and broken flashdrive that had important music on it, worked like a charm!!! You Sir are a genius, Thank you and God Bless.

@ElectronicsComputers

2 жыл бұрын

Glad it helped!

Thank you SO MUCH for this informative video. I was easily able to identify the problem and temporarily fix it long enough to retrieve the files I needed. Thank you for your simple yet effective explanation!!!

@ElectronicsComputers

2 жыл бұрын

Thank you for letting me know, I'm glad I could help you in that way.

Thank you thank you thank you! & the copy tip instead of cut was much appreciated! Thank you !

@ElectronicsComputers

2 жыл бұрын

Glad it was helpful!

Thanks for the detailed instructions!

@ElectronicsComputers

2 жыл бұрын

Glad it was helpful!

I used the wire method without soldering and it work like a charm 👍thumbs up

@ElectronicsComputers

4 жыл бұрын

Nice work! happy to help!

Oh my goodness!! I was going to cry and I don't know what else. I bent my flash drive in which I had stored all of my coursework for this unwanted class I had to take for the Florida Dept. of Education. I did everything I could to try to get this thing to work. Your video was the first one to come up, so I decided to watch it. I was able to open the plastic that encloses the components of the flash drive. I saw the pins you were talking about and, as you said, I don't have a small soldering iron. So I used my thumbnail (actual thumbnail). Good thing it was long and was able to hold those pins down enough so that I could get the one file I needed. I can get the others later on to move to another flash drive. It took only 2-3 minutes, but they were painful as I had to press down hard so that the pins stay down and I would not have to restart the whole process after three times of trying. Thank you so much. God bless you.

@ElectronicsComputers

3 жыл бұрын

Thank you for such an honest comment. I'm happy to help!

Thank you so much I had so many important documents on there🙏

@ElectronicsComputers

3 жыл бұрын

You are so welcome

Helped me some much! Absolute hero.

@ElectronicsComputers

Жыл бұрын

I'm glad I could help. Like and subscribe if it helped you a lot.

You are a life saver. Thank you for sharing!!!

@ElectronicsComputers

4 жыл бұрын

I'm glad I could help you!

@mexic8l

4 жыл бұрын

@@ElectronicsComputers hello?

You just saved my life, thanks!

@ElectronicsComputers

4 жыл бұрын

I'm glad I could help you!

@mexic8l

4 жыл бұрын

@@ElectronicsComputers hello?

Thank you so much man, I’m about to try this out. My USB bent because my laptop fell off my bed and it bent my drive.

@ElectronicsComputers

Жыл бұрын

Glad I could help!

Thanks sir, files now rescued for my neece. Super video

@ElectronicsComputers

3 жыл бұрын

I'm happy to help!

I have a study drive and it broken and with your help you saved me

@ElectronicsComputers

3 жыл бұрын

I'm glad I could help you!

@jassarsalemalkahtani7852

3 жыл бұрын

Bro that’s a 4TB Of data almost lost but you are a GOD at these Things

Thank you so much. I saved all my files and saved hours of work redoing them...

@ElectronicsComputers

Жыл бұрын

Glad I could help!

I had a pendrive circuit with some documents now i can connect it easily

i love your channel bro :) thank you

@ElectronicsComputers

2 жыл бұрын

Glad you enjoy it!

@Electronics&Computers Thank You, Thank You, Thank You! You helped me save alot of money and invaluable amounts of data. I appreciate you posting this video.

@ElectronicsComputers

Жыл бұрын

I'm happy to help and thank you for your support!

Good video, very informative.

@ElectronicsComputers

2 жыл бұрын

Glad it was helpful!

Cheers! Soldering was too difficult, so I ended up hot-gluing the wires to the contacts. Worked though!

@ElectronicsComputers

4 жыл бұрын

Happy to help!

@marianavasquez854

4 жыл бұрын

How did you hot glue it????

@ReddwarfIV

4 жыл бұрын

@@marianavasquez854 I used a hot glue gun...?

Amazing video. And you also replies to almost everyone. Amazing work dude. Keep it up. Most people doesn't even reply to those who need help.

@ElectronicsComputers

2 жыл бұрын

I'm happy to help and thank you for the comment!

The 'bend' trick saved me $2,000 dollars from those repair companies who would probably do the same thing. My hand got hot holding the flash drive in place while the data transferred but lesson learned.. don't save your important stuff on a plastic, flimsy drive. Thank you!

@ElectronicsComputers

6 ай бұрын

Great job! I'm happy to help!

Thank you!! You saved my precious Mark Minervini stock trading files 😂

@ElectronicsComputers

3 жыл бұрын

Glad to help!

Excellent video. Soldering to the microcontroller was most impressive. I would probably bridge the two points with solder if it were me with my sub-par soldering skills. lol

@ElectronicsComputers

2 жыл бұрын

thank you for the comment!

Sir, this video is a god-send and literally just saved me $1,000+ dollars! Thank you soo much for this short and very straight to the point video!

@ElectronicsComputers

3 ай бұрын

I'm so glad I could help you! Please like and subscribe.

I CAN'T THANK YOU ENOUGH! I figured as long as the pads were intact, the connection shouldn't need soldering to work. But you've confirmed these methods, and restored my faith in reality. Not to mention you considered the fact that the average being doesn't possess soldering equipment, unlike the rest of KZread XD. Thank you!

@ElectronicsComputers

Жыл бұрын

Glad I could help!

Thanks!

@ElectronicsComputers

4 жыл бұрын

Welcome!

Thanks soooo much!!

@ElectronicsComputers

3 жыл бұрын

You're welcome!

Very very thank you so much bro 😅😅

@ElectronicsComputers

4 ай бұрын

Welcome 😊

LITERAL LIFE SAVER

its working thanks bro

@ElectronicsComputers

3 жыл бұрын

Welcome

OMG I can't believe I made it work

From "1:49-1:53"... what if I did that with "krazy glue" to prevent a short circuit as I don't have what u'r using to prevent the short circuit? Would it still work? or else I'mm gonna have to stick in with only holding broken USB connector on the "Flash Drive".

Full support 😊😊

@ElectronicsComputers

3 ай бұрын

Thank you for the comment!

This is the most helpful video 've seen because I owe you 128 gb

@ElectronicsComputers

2 жыл бұрын

I'm glad I could help you!

Thanks for the video. I have a USB 3.0, so it has 9 connectors. I saw on a comment you said you can use it with 4. If I don't have a multimeter can I just put the wires in the same order and it'll be safe?

Thanx bro

@ElectronicsComputers

3 жыл бұрын

Welcome

I will try and let you know thank you

@ElectronicsComputers

3 жыл бұрын

I hope it worked for you.

@engabdallayusuf2910

3 жыл бұрын

Sir I will update you soonest

Great video! but can you please raise the volume?

@ElectronicsComputers

5 жыл бұрын

Thank you for the comment! I'll work on the audio quality!

@mexic8l

4 жыл бұрын

@@ElectronicsComputers hello?

Thank uuuuuuuuuuuuuu

@ElectronicsComputers

2 жыл бұрын

You're welcome!

Thank you so very much for your time and effort in making such clear and concise video. This is one of those curve balls and and I need your help, if you don’t mind. I’m helping a friend with his program security USB. His kid knocked the USB out of his PC. The USB was bent and ultimately broken. With much difficulty I managed to open and take out the board. This board is not your “typical board” with 4 lines coming out of it. It is “U” shape with 4 points behind it. The question is how would I be able to determine the appropriate pins? Can I share with you a picture of the board? I couldn’t find any diagrams on line either. Thank you in advance.

@ElectronicsComputers

Жыл бұрын

Send me close-up photos of the board from both sides.

@robertodecarlo646

Жыл бұрын

I thank you so very much for the response. I have the pictures however, I have never post a pic on the KZread comments. Any suggestions would be greatly appreciated. Thanks again.

@robertodecarlo646

Жыл бұрын

@@ElectronicsComputers I did more on line search and find out this USB is a “B” type with its pin layout. However, I still want to send you the pictures for confirmation, don’t want to take a chance. But and I as mentioned before, I don’t know where to send you the pictures. I would appreciate any assistance you could provide. Thanks in advance.

I did the wires to usb board and it started to flash a red light and started smoking it doesnt work for me

So I dropped my flash drive on accident and there seems to be no damage on it and when I connect the usb the light on it quickly flashes once and it stays off after that does that mean the flash drive doesn’t have power going to it when its connected?

Do you need flux to solder at 1:50min? soldering the wires to the board vs cpu. Also my USB doesn't have a metal connector, its like a flat brown spot. is it ok to solder to that or would i need to connect to the cpu? It is a retractable Cruze USB. 4 connection points.

@ElectronicsComputers

2 жыл бұрын

You always need to apply flux on exposed copper wires or PCB traces. Can you show me a close-up high resolution image of your drives PCB?

I do really have the same problem

I tried to connect the wires to the board then connecting it to my pc to see if it works, the pc recognized the sound board(usb) but the next day when I tried again my pc didn't recognized the sound board anymore, I just kept hearing the connecting usb sound. How do i fix it ? I want to make sure the sound board is recognized by pc before soldering.

i have a flash drive with all of the metal on the plug-in parts. all 4 pad are completely ripped off the board. where you only can see green spots where they were on the board itself. i have a soldering iron coming in a few days. i have cord i can cut and use what would be the best method to continue.

@ElectronicsComputers

2 жыл бұрын

All you have to do is carefully and correctly solder wires to the PCB. If you go to any repair shop, they would do the same thing and charge you at least a hundred bucks.

@huntor52

2 жыл бұрын

@@ElectronicsComputers even possible in my case where the solder joints are completely ripped off the board? The pins are intact but the solder joint were ripped off the PCB.

1:53 "if some of these pads have been ripped off the board" - what if all four of them are now missing?

@ElectronicsComputers

2 жыл бұрын

You need to figure out where those traces lead and solder wires to the other pads.

Hey, the front part of my usb fell out, and the drive is still in there. How do you recover the files?

Is your solder already in the solder iron because I didn’t see you put solder when you heated up the circuit and what solder iron are you using?

@ElectronicsComputers

3 жыл бұрын

Yes, I applied solder on the tip of the soldering iron first. I couldn't do it another way because I was holding the wires in one hand and the soldering iron in the other. The links for all the stuff that I used in the video is in the description below.

WOW 😮

@ElectronicsComputers

2 жыл бұрын

I hope it was useful.

This method works! But unfortunately when I connect the wires to the broken USB head my computer makes the connection noise but it automatically states that there is a problem with the device and that it wasn't able to install it successfully. Do you know any fix for my laptop to allow me to access the files? I see it is connecting but it's not appear local disk just getting error messages..

@ElectronicsComputers

3 жыл бұрын

If you're connecting a USB cable to the PCB board then try to reverse two middle data wires.

I have a USB 3.0 with 9-pins. I 'm guessing the black ground & the red power wires go on the far left & far right pins respectively, but can the green & white wires go to any of the remaining 7 pins? Does it matter which ones I connect them to? Thanks!!

@ElectronicsComputers

2 жыл бұрын

You have to wire your USB 3.0 drive in 2.0 version. So for data transfer you will use only those two pins in the needle of the connector and ignore the rest. You can see at 1:23 where white and green wires should go.

Pov you had an assignment due in a couple of days but your usb decided to die on you but you watched this bideo so it got resurrected in time 🥳🤰

my usb pendrive not detect..what to do?can u help me

Sir, which four connectors would I need to use in the case of having a USB 3.0 drive?

@ElectronicsComputers

3 жыл бұрын

There will be 5 contacts for USB 3.0 and 4 contacts for USB 2.0 connection. I recommend using USB 2.0 interface because it has less wires.

Please show the pin out path like CLK CMD DAT0 greetings from Indonesia  😊😊😊

Hello Sir, thank you so much for your video!!! I have a few questions, because i did not understand some answers from you. I have a Hama USB Stick with 9 wires. Did i understand it right that i can also use only 4 wires? So the far left and right ones are black and red but where does the other go, the white and green one. I did see multiple times your video but i still do not get it. Or could you please let me know how to connect 9 wires? Thank you so much. Kind regards!

@ElectronicsComputers

Жыл бұрын

I hope this will help: ibb.co/GV8snz6 There's no need to solder all 9 wires. For USB 2.0 connection you'll need only 4 wires.

@Sara-to4yj

Жыл бұрын

I understand but where do i connerct the 4 wires to the 9 contacts on my stick?

I wish I could just find a place to recover my data from my flash drive and not charge me like $300. I’m in Orange County CA. Any recommendations?

what you stick with??? I can stick witch superglue or something?

@ElectronicsComputers

4 жыл бұрын

you have to solder it!!!

Hey, my broken USB drive uses USB C, is there something I can do to recover its data?

would this work with a usb receiver? like hyperx cloud stinger?

@ElectronicsComputers

2 жыл бұрын

Sure! Same process.

if there is no external (soldered on) USB connector, could I solder to the USB contacts themselves?

@ElectronicsComputers

3 жыл бұрын

You can solder it directly to the USB port if those contacts are not broken and have reliable connection with the PCB.

Hello I have a 3.0 SanDisk USB drive. I heard that's fine it will still work with the 4. However I know that each pin is for a specific thing on the 3.0 so witch pins would be the 4 pins of (GND) (DATA+) (DATA-) (+5V) out of the 9 pins on the SanDisk 3.0?

@ElectronicsComputers

Жыл бұрын

Red contacts for USB 3.0 and White ones for USB 2.0: ibb.co/281PNhH Simply use white ones to power your flash drive and transfer data.

@xxSOULREAPER25xx

Жыл бұрын

@@ElectronicsComputers Ok thanks that was extremely helpful, so I only need to use the data - and data + for data transfer? On a 3.0 and it would still be the same on a 3.0 where data - is green and data + is white thats where I get a lil confused

@ElectronicsComputers

Жыл бұрын

@@xxSOULREAPER25xx Forget about USB 3.0 connectors. You have 4 wires, two provide 5 volts and two data transfer. For USB 3.0 you need two receive and two transmit wires and also two wires for power.

If I bend a usb, is it more likely I break the port itself or the USB itself?

I got a full metal one and it makes the connect sound on windows but nothing shows up... I got it open but it doesnt have a lil board in it but just a plastic covered small one. Is there any fix for those too or is it rather lost for ever?

@ElectronicsComputers

27 күн бұрын

It's almost impossible to deal with the latest USB drives without the microscope and hot air station.

@Crewiz191

27 күн бұрын

@@ElectronicsComputers aw man okay. Well that’s unfortunate then. Thank you for the quick response tho

I have a Kingston 64 GB one that my sister just broke and I have no idea how to open it.

Almost all my uni work is on mine I hope this works

@ElectronicsComputers

3 жыл бұрын

Did it work for you?

@Emilia-fp3pn

3 жыл бұрын

@@ElectronicsComputers sadly nope the IT guy at my uni said it was gone :(

@coldblackice

3 жыл бұрын

@@Emilia-fp3pn Send it to me, I'll do it

Question, I have a usb with 9 connectors, is it just to put togheter?

@ElectronicsComputers

4 жыл бұрын

That's a USB 3.0 connector. You can only connect 4 terminals and it will work as a regular USB 2.0 flash drive.

@mexic8l

4 жыл бұрын

@@ElectronicsComputers hello?

Hi, I have 9 pins coming from the USB onto the board. Are only 4 of these being used? Or what? Thanks for any advice!

@ElectronicsComputers

3 жыл бұрын

you have USB 3.0 drive but you can use only 4 contacts and it will work as a USB 2.0 drive.

@MJ720

3 жыл бұрын

@@ElectronicsComputers Thanks!

@MJ720

3 жыл бұрын

@@ElectronicsComputers Hi, me again. Do you know of a place I can find a schamatic or similar of a 3.0 usb to figure out which 4 contacts to use? Thanks

I'm missing 3 pins but the ground pin is still there. What would i do then?

Can I mail you my board and have you do this for me??? Super important

what if one of the 4 pins is broken off, have any idea if it will still work?

@ElectronicsComputers

Жыл бұрын

You have to find with a multimiter where that pin goes and solder a wire to that pad or component.

Mu usb has not been completely separated, what can i do in this situation.

@ElectronicsComputers

3 жыл бұрын

Just solder that port down or try to make a contact by pressing the USB connector to the board and then backup your information.

Will this work on a kingston hyperx flash drive 64gb?

@ElectronicsComputers

4 ай бұрын

My instructions are universal for any flash drive. Of course, I can't cover the disassembly and show pinouts for all flash drives, so you have to figure out the last step yourself.

0:55 very frustrating. They need to change the process of cutting, "Cutting" files should not delete them until after they were successfully copied and verified before deleting to complete the cutting process.

@ElectronicsComputers

2 ай бұрын

Oh, I totally agree with you. I've lost so much information because of how the cutting feature works. Now, I always copy important files and then remove them if I don't need them.

Hey I'm just wondering is there a risk of being shocked when I plug in the usb at 0:41?

@josedcarrillo24

3 жыл бұрын

@Electronics&Computers

@ElectronicsComputers

3 жыл бұрын

With what? 5 volts????? It's impossible!!!

I have Sony pendrive 7 pin in there what i do

Please tell me what does it mean if the first time when I touched the wires to the pcb my windows recognized the device but the next day when I tried again it didn't recognized the device.

@ElectronicsComputers

2 жыл бұрын

Bad contact with the PCB

I have a cruzer glide 32 GB flash drive I bent and broke the usb peace and it has important

@ElectronicsComputers

4 жыл бұрын

disassemble it and try my methods.

what if solder on ground pads are missing the black and red one where do i connect them ?

@ElectronicsComputers

3 жыл бұрын

you have to find the other solder pads which were connected to the ripped off ones. Without a multimeter it's almost impossible task.

@luthandovilakazi870

3 жыл бұрын

What if only the black one is missing in usb cable?

@ElectronicsComputers

3 жыл бұрын

@@luthandovilakazi870 What wire colors do you have in that cable?

It says “Unknown USB Device needs more power than the port can supply” what do I do? Do you think it might be the usb cord I used to solder the wire and the usb with?

@ElectronicsComputers

3 жыл бұрын

Double check your wiring and make sure that there's no short circuit.

@boruto4473

3 жыл бұрын

@@ElectronicsComputers is it possible to fix a short circuit and how do I check to see if there is a short circuit

I have cut open a usb cord but it only had black and red wires inside, can I still use this method without the green and white wire?

@ElectronicsComputers

3 жыл бұрын

No! If your cable has only two wires then it's not a USB data cable it's just a charging one.

@sophiedodd5140

3 жыл бұрын

No worries I have to send mine away it is a NAND chip or something Thank you for your help and the video anyway :)

i tried the first method. when i hold the connector to the board and plug it into the computer the light turns on. strong and steady but the computer is not showing a usb connected. what could be the issue?

@ElectronicsComputers

2 жыл бұрын

Make sure that the data wires (green and white) have a good connection with the traces/solder pads on your flash drive board.