The same problem. It also was rear left ABS sensor. It happened about 100km after hand brake pads changing. The newer tool I used for diagnose (possible to buy nowadays) is Foxwell NT 360 Plus. Thank you for video. Here in Sweden the Wrangler is not such a common car and spare parts are extremely expensive. Waiting time is three or more weeks... Horrible service. Thanks, with your help I was able to fix it.

I am glad you mentioned the "BRAKE" light makes you get stuck in gear. Exactly what happened to me today thankfully I was a block away from my house. My Abs and traction control lights came on after replacing my rotors and brake pads. Flash cal indicates "erratic front left and right tire performance" so I guess I found the culprit.

well done - start to finish!

Thanks for the video. Other videos were showing how to take the brakes off, etc. and your video is far less intimidating. I know it's not as easy to get the hands back there but I think I can do this.

Cool video, to the point and great presentation. It's appreciated.

@The.Odyssey

Жыл бұрын

Thanks for the feedback! Let me know if you have any issues

Really appreciate your guide. My jeep just started having these lights turn on recently and I hope it’s just the sensor but if it’s the wire then your how-to will definitely save me a lot of money on repairs. Liked and subbed!

@The.Odyssey

8 ай бұрын

Thanks for watching and subscribing! Have you narrowed it down to a specific wheel with a scanner?

I have the same problem. Good helpful info and video.

@The.Odyssey

Жыл бұрын

Thanks! I wish I would have shown the fronts too, but glad this helped you!

Abs and traction are on as well as the brake but thanks to you I now have anything thing I can verify regarding the two wheel speed sensors I replaced, although when I connect my scan tool I'm getting a P0501 for the VSS but can't find any real information on it regarding my mom's 2012 wrangler jk

Thanks great video I only got traction control light showing

Great vid. Thanks for sharing!

@The.Odyssey

Жыл бұрын

Thank you for watching!

Good job man!

Thank you very helpful video

@The.Odyssey

2 жыл бұрын

You're welcome!

Thank you for the informative video. My Jeep has that code and buying a better code reader to find the problem ESC sensor and do the fix.

Outstanding fix and narrative

@The.Odyssey

Ай бұрын

Thanks, I did a similar job Friday for a jeep grand cherokee. Hoping that video does as well as this one.

Thank you brother

Hell yeah, thank you brother!

@The.Odyssey

Жыл бұрын

You're welcome! Glad this video helped you

Thank you!

Thanks dude, I hope the problem on mine is just as simple.

@The.Odyssey

2 жыл бұрын

Hopefully. If you need some troubleshooting help as you go through it just ask me here. The dialog can help others as well.

Thank you

I have these same lights on plus the odometer and gear indicator seems to flicker when they illuminate. It only seems to happen when ive been driving in 4wd then shift back to 2wd. The lights go away and all is good after I turn off ignition and start back up. Any thoughts? Otherwise, Jeep is perfect. 2013 Rubicon 4" lift.

Im having the same issue. Im also throwing a code for the abs module.

Good info. Mine just lit yesterday, although they are not constantly on. I'm hoping that it's just a sensor and nothing more serious.

@The.Odyssey

7 ай бұрын

Yeah, I really expected an abs sensor on this. Fortunately I saw that crushed portion of wire of this could have taken me much longer

Great information. I just replaced the clock spring in the 2013 JK about a week ago and now I have a traction control light on. SoI have to try and figure out what’s going on. I subscribed to your channel looks like good information. Thanks

@The.Odyssey

Жыл бұрын

Thanks for subscribing! I only wish I would have explained or at least showed the location of the front abs sensors as well.

@russellwood5173

Жыл бұрын

NEED TO RESET STEERING ANGLE SENSOR WITH A SCANNER.

I have the red light bolt and the track stability track lights on can’t figure out what the issue it’s starts to shake a little plus slight of a rough idle

Did you happen to have codes P0573, and P0571? I am also getting the ABS light and traction control light as well. To me, that is a brake light switch that needs to be replaced. However, I also know that with the ABS light and traction control light, that is typically in my experience a wheel speed sensor. What are your thoughts? Thank you, Chris

My abs and traction control turn on and off sometimes even my check engine turn on can u help does this have anything to do wit the transmission.....?? Plz heelp

Always use air and blow off the speed ring,before reinstalling the speed sensor.

what brand sensor did you go with!

Is it safe to drive on? It only brakes when I leave my driveway after that it's normal

So you found a loose sensor, and electrical tape in there? Sounds like someone else took a crack at this in the past but didn't quite finish the job. Thank you for posting everything you found. Everything was useful, right up to the end where you showed the lights fixing themselves without the need for a scan tool. Thumbs up.

@The.Odyssey

Ай бұрын

@jima4656 I actually just did another abs video (uploading now) on a grand cherokee, I did reset that one with the scanner, but I didn't give it much of a chance to reset itself. The video you are commenting on though was a crushed wire from the bump stop and I repaired the wire.

Apparently this is really common. I got new shocks, 2.5" lift, and steering stabilizers put on last week. The next day the same thing started happening to my 2014 Rubicon. I took mine back to the shop today for the same thing, plus my hill descent assist light flashes too. They told me I need a new ECM. They didn't even check the sensors.

@The.Odyssey

Жыл бұрын

Yours was also the wire?

@melissapearce2542

Жыл бұрын

I don't know yet. I will check it out this weekend.

I had the ABS, BRAKE, and traction control lights on with mine. Wasn't the wheel speed sensor at all (the code read differently, I can't remember what it was now). There is a sensor on the brake booster - little grey thing, pops on the booster and then has a connector that plugs in the side of it. Jeep calls it something weird - power brake booster check valve. I changed that out, drove it about 200 miles, and it went away.

@The.Odyssey

2 жыл бұрын

Nice, yeah with the different code it probably leads right to that. Newer cars are a double edge sword... if you know how to interpret what the codes mean it will lead you right to the problem. However, the problem is more often then not the sensor that is supposed to be monitoring for a problem or a wiring issue. Thanks for the comments! Love the interaction with you all.

@kimcliftrn

2 жыл бұрын

Going to do a video speak up so people can hear you .

@The.Odyssey

2 жыл бұрын

@@kimcliftrn thanks for the feedback. I have received similar and have added steps during editing to address the issue.

@stevestewart3816

Жыл бұрын

I have a 2016 jku and the brake,tc control and the abs light came on and went back off, I ran the codes and nothing popped up. I used j scan

My abs light and traction control light goes on and off, usually comes on when I’m breaking and turning at the same time, but in my case my breaks feel like it skips/jerks when turning and braking at the same time. Did you had the same problem?

@The.Odyssey

Жыл бұрын

I did not. I would bet this is going to be a front sensor or front wheel bearing. Probably the bearing. Do you hear any noise when turning left or right?

@ms.t8950

Жыл бұрын

i have 2016 doing same thing you find the problem on jeep ? thanks jt

@leoluna96

Жыл бұрын

@@ms.t8950 mine does the same thing, have you figured it out?

@parkernichols2039

Жыл бұрын

Mines doing the same, keep me updated on your findings, I’ll do the same

@leoluna96

Жыл бұрын

@@parkernichols2039 check engine just turned on for me with code p0572. Just ordered a brake light switch, will keep posted

My abs light and my traction light is on. I bought the scanner tool to see the code but if you have any idea let me know

@The.Odyssey

2 жыл бұрын

The scanned is your Best friend. It should lead you to what you desire.

Are these related to C121C code? And would any of those codes cause the jeep to stall?

@The.Odyssey

Жыл бұрын

I don't know for sure. Researched quickly and it looks like this would lead to a bad PCM or ABS module (controller). What im wondering is if you have a grounding issue, seeing as you are also stalling. Make sure your battery connections are clean and that the grounds going to the engine and frame are making good connection as well. Let me know if you find anything

2015 Jeep JK automatictrans.. Ok, ABS light, Brake light, and while driving will not as I accelerate will not shift from first. Any ideas. I'm having a friend bring over a code reader tomorrow but thought I'd ask anyway, thank you in advance

@kengennett3121

2 ай бұрын

Did you figure out the issue?

does this also drain the battery? or have you ever stumbled upon that problem of the battery dying over night

@The.Odyssey

2 жыл бұрын

This shouldn't drain the battery. I would start by going to a parts store and asking them to load test your battery. If that passes then move on to finding out what is drawing power with the key off.

Got the same lights on my WK. Mine is the g sensor code, c1210 that keeps showing up. I've replaced the sensor twice now and the readout on the scantool shows that it's not stationary when it's... Stationary.

@The.Odyssey

Жыл бұрын

Sounds like it could be one of a few things. - The sensor (which you have replaced twice so lets rule that out) - Incorrect Voltage (could be low or high) I would make sure battery terminals are clean and that there isn't a fuse on the circuit. (a quick google search did not point me to a fuse being in the circuit but I haven't looked at a diagram). - Possible broken wire going to the Sensor, a poor ground, or a broken electrical connector. - I would suppose you could still have an issue with a wheel speed sensor. If you have a meter that shows readouts like the one in the video does any individual sensor read significantly different than the others? Being that you state that the scan tool shows not stationary when stationary I am leaning towards low voltage as I assume the reading that it gets back is not what it expects. I don't have hands on troubleshooting for this issue so at this point that is just a guess of mine and the direction I would go first. If you've got corrosion on the battery terminals or cables take them off, clean them up and retest. After that I would be looking at the wires going to the connector for this sensor. Finally, if that didn't work I would unplug each of the sensors one at a time and drive it to see what happens on the scan tool, if something seems inconsistent I would make an educated guess on what wheel sensor needs to be replaced. If none of that works I would probably set it on fire and call the insurance company.

@amylaurin7269

Жыл бұрын

@@The.Odyssey Lol on the setting it on fire and calling the insurance company. I was able to look at the readout for the ABS sensor, yaw and dynamics readouts. It looks like the calibration is out on the longitudinal sensor. After trying to use my aftermarket software (AlfaOBD), it looks like we might need a different scan tool to run the sequence. Wiitech and HPTuners seem to have learns routines that work a lot better than Alfa. I'll pull out a multimeter this weekend and go through the electronics and look for a fuse. Thanks for comment!

So I replaced my front pads afterward afterwards when I turn left my ABS and track light come on but then we'll eventually go back off and then if I turn left it comes back on, I tried while sitting just turning the wheel about a 1/4 turn it comes back on and then goes back off sometimes or after i drive a bit, this just happend, I don't have a scanner. could a pinched line do this?

@cheeseNrice69

2 жыл бұрын

Fixed my dumb-ass flipped the caliper before I put it back on and I kinked the hose

@The.Odyssey

2 жыл бұрын

Glad you figured it out. I was thinking the wire going to the sensor in the wheel bearing

I’m getting a code for my jeep U1120 but I don’t have a scanner. I can’t find any info on how to fix and where it is

@The.Odyssey

Жыл бұрын

Looked this up and it seems to be a communication issue between the abs module and the computer. I would start at the fuse and make sure it's good.

Thanks for this video. My and light doesn’t come on BUT my traction control is and jeep is running real sluggish. Do you think it’s the wheel speed sensors?

@The.Odyssey

29 күн бұрын

It could be, that scanner would give you more info. Cars do funny things, they can go into limp mode to keep you safe. But then you are late to work because the jeep is sluggish, you get fired, and then you can't afford to fix it. These damn engineers.

@tdz69

Күн бұрын

@@The.Odyssey lmao

getting the same codes but the wires looked good. there is some in- out play in the left rear axle. its about 1/8". (the right rear axle has no movement). would that cause the light?

@The.Odyssey

Жыл бұрын

Yes, that could. How much play are we talking?

@The.Odyssey

Жыл бұрын

Just saw you said 1/8 inch, I replied to quick. Have you pulled the drum and inspected the ring that the sensor reads? Make sure it's clean. Have you replaced the sensor?

@joed8202

Жыл бұрын

@@The.Odyssey thanks for reply. I replaced sensor and harness. I cleaned the tone ring. The same codes appear as active- C1043 u140b.

@The.Odyssey

Жыл бұрын

@@joed8202 ok, are you watching live data on a scanner to see exactly what it is reading or just getting a code?

@joed8202

Жыл бұрын

@@The.Odyssey just codes from bluedriver. I dont have a live scanner

I have had this on for 3 years. I've tried replacing the sensors twice and new plugs for them as well. Still ABS is still showing right rear. Any help on this? BTW, 2011 JKU.

@The.Odyssey

Жыл бұрын

Did you inspect the wires as shown in the video?

@JoeMartin1968

Жыл бұрын

@@The.Odyssey I just finished watching the whole video. I did not do that part. I am heading out there now. Thank you for the quick reply.

@JoeMartin1968

Жыл бұрын

I did see the crushed wire on the right rear as it was laying right where the bump stop hits. The yellow wire was definitely broke. I replaced that section but it is getting dark here. I may have to the black wire as well. But you were dead on the money sir. Thank you.

@The.Odyssey

Жыл бұрын

@JoeMartin1968 awesome! Hopefully this fixes your issue. Let me know when you are done.

My 2014 jeep wrangler sport whenever I put it on cruise on highway speeds as in 70-75 my traction control pops on and then turns right off could that be a speed sensor? I had it the other night when it first happened it threw a battery abs and traction control lights but ever since it’s only been the traction control kicking on and then turning right off

@The.Odyssey

4 ай бұрын

The truth is it can be any part of the abs system. Watching a monitor like I did can help narrow it down. In my case here it was the wires going to the speed sensor.

@jacksonando2612

Ай бұрын

Does yours kind of jolt when the traction control comes on? Mine does the same thing at 70 mph but jolts when it lights up then it goes away

@donovanjustice2233

Ай бұрын

@@jacksonando2612 it ended up being a loose battery terminal it felt like a stall

@The.Odyssey

Ай бұрын

Nice, I came to give input and it's already happening. Good info, check / clean your battery terminals as it's free and a quick thing to try

@jacksonando2612

Ай бұрын

@@donovanjustice2233 yes exactly like a stall. How was the repair? Easy at home fix? Or something I gotta take it to the shop? Only had my jeep a year, so I’m new to working on repairs and upgrades

Have a 2015 Wrangler unlimited. Doesn't happen all the time but when I hit the brakes it feels like the abs is engaging . If I pump the brakes before coming to a stop it brakes ok . Brakes feel good when stopping . I get no abs or traction control lights coming on. Hooked my Zurich OBD2 code reader which diagnoses and erased ABS codes/lights and it shows nothing. Got any ideas on what to look for? Thank you

@The.Odyssey

8 ай бұрын

If hooked up can you watch speeds of each wheel on it? If so I would do that and see if one seems off. Going around corners you should see differences but straight like should be the same.

@HeavyChevyMega

8 ай бұрын

@@The.Odyssey I think my code reader only shows up if there is a light showing up and which sensor on the vehicle it is , but I'll check it.

@HeavyChevyMega

8 ай бұрын

Just went onto my ZurichZR13 ABS button & it said no codes and then I hit LD for live data and it said "this tool does not support ABS Live Data".

@The.Odyssey

8 ай бұрын

Either of the front wheel bearings growling?

@JonLevel2

6 ай бұрын

Same issue rn.

So it wasn't the sensor... just a shorted wire? My lights just came on leaving the driveway.

@The.Odyssey

2 жыл бұрын

That was the case with this jeep. It could be a front too which is in the wheel bearing but wasn't covered in this video. First step is to get a scan. If you need ideas after a scan let me know.

Your missing clip can cause the issue that happend to me

@The.Odyssey

Жыл бұрын

What happened to you?

how i fixed it on my wrangler: just washed it with soap and 110 bar water stream)

For all us non mechanics, about how much should this cost to repair for 2013 jeep wrangler unlimited?

@The.Odyssey

2 жыл бұрын

To have a shop do or or to purchase parts / tools and do it yourself?

Can a bad front wheel bearing cause this problem?

@The.Odyssey

Жыл бұрын

Yes, a bad front wheel bearing (or sensor) can certainly cause issues with the ABS

@The.Odyssey

Жыл бұрын

I added a link to a brand I like to use at a decent price for a front wheel bearing ( amzn.to/3WAxHca ) if you need one. I get a lot of parts from Detroit axel with good results

Seems like its always the left rear...

@nikkianderson5076

Жыл бұрын

It really is! 😂

@lordaizen2192

Жыл бұрын

Yep for me as well

@elliottberkley

Жыл бұрын

Also me.

I ran over a nasty rail road tract and caused abs&traction light to come on.

@The.Odyssey

Жыл бұрын

I'll bet a wire at the bump stop