Вот это настоящий ремонт👍😊😊 КАКОЕ СЧАСТЬЕ БЫТЬ МОЛОДЫМ😊😊😊

This is a game of patience, and learning (to a point) on the job. That's some fan!, on what seems to be the main motor!

Well I was going to give it a try but im a little worried of messing something up. Its good to see that it may only takes about an hour so perhaps i will have a shop do it for me. A shop up the road is $85 an hour. plus the taxi to get it there and back lol. Great video ,almost good enough for me to follow along with you but as someone pointed out there is a part perhaps missing. I wish it were as easy as spraying alcohol and adding oil.

This was excellent. I couldn't move the little PCB in the rear, as it is held on one side by a very small nut, and could not get it removed. But everything else was great. Thank you for the video.

!!!!WARNING!!!! Video does not show re-installing insulators on power regulator board!! Very important to isolate the resistor or else smoke signals will be made. It’s better to leave the board connected and remove the two screws holding the POWER IN connector. Then it will not be in the way.

@AudioPhool

8 ай бұрын

I was going to place the similar warning DONOT GROUND THE TRANSISTOR TO THE FRAME you will lose sound from both channels make sure you replace the clear plastic square that falls into your machine when you remove the screw and nut on that board IMPORTANT

Very useful detailed guide

Good job

During FF/RW, is sounds as if the tape is very close to the playback head? I wonder if the tape lifter can be raised a little more?

Novel approach, removing the two screws instead of removing the solenoid. Was looking to see how you dealt with the pressure spring that linked the solenoid plunger to the pivoting arm that you removed that was held on with two screws. You didn't show taking those out or putting them back in, must have been a bitch, but without that critical step this how to is incomplete. I assume you put the transistor insulator back on the voltage regulator board that is mounted on the back of the unit. That is used for the bias oscillator. A note on cleaning of pinch rollers and handling of belts. If you don't have proper rubber cleaning chemicals then water is recommended and skin oils begin the deterioration of rubber belts so avoid handling then. But there appear to be dozens of opinions on this subject, but then I have bottles of Teac rubber cleaner. There's lots of reading material on this subject.

I'm working on a A3340S where the pinch roller solenoid won't even try to engage. The mechanism is free to move, but the solenoid is only getting 7.6 VDC and not strong enough to overcome the spring loading that pulls the roller away when stopping the tape. I tried to pull a schematic off hifiengine, but their site is giving a 500 error when I hit download. Is that solenoid powered by 12 or 24 VDC? I really need a schematic to trace where the power comes from and why that circuit is soft.

@axelthefoxytechworld8024

3 ай бұрын

it could be 12v or 24 volt either 7.6vdc sounds low to me likely the powersupply needs recaped ive never worked on that nore have i ever had that problem

@basspig

3 ай бұрын

@@axelthefoxytechworld8024 Ripple was my first thought. But there is negligable ripple across the solenoid. I finally procured a schematic and it is more complex than I expected. This solenoid may be in series with diodes and other solenoids depending on the state of various relays. Ugh. But thanks for confirming the voltage should be higher.

Hello,you need to, replace you take up Reel, brake then, it will stop, spilling the Tape.

@axelthefoxytechworld8024

2 жыл бұрын

The reason it did that is cause the pinch roller wouldn't engage so I had to do it manually

Do you know how to install a computer socket for the power cord? Mine is missing the power cord and i want to install a computer socket so i an use one of those power cords. Thank you

@SDsailor7

Жыл бұрын

So you don't know how that is done?

What’s the best type of oil to use ? Great video !

@axelthefoxytechworld8024

Жыл бұрын

3-in-one oil or zoom spout if you want the best oil there is thats what i used on this im glad you liked it

@AudioPhool

8 ай бұрын

sewing machine oil its cheap and it works very well works good on the motors so fill them up

I just flush with 99.9 anhydrous IPA to flush old grease into a cloth. Same with the solenoid. Add oil. Done.

it looks new

I’m sending my 4010sl over to you for the same thing. Think I’ll just spray lube it 🤷‍♂️ 🤦‍♂️

37:28

I like the blue reel you have on the player will you like to exchange I will like to have it.

@axelthefoxytechworld8024

8 ай бұрын

sorry no

Hey I just followed this tutorial and my teac and now smoking fuses in the top right and the play button now does not work at all

@axelthefoxytechworld8024

Жыл бұрын

idk why it would do that you prbaly didnt put it together right if anything could be bad caps finaly leting out the ghost an yeah that happened to me to the micro switches on these the plastic is geting brittle so i had to replace my play microswitch

@Treepadawan

Жыл бұрын

Where is the microswitch located?

@Treepadawan

Жыл бұрын

I think my most of my capacitors are fine it’s just a specific spot smoking

@Treepadawan

Жыл бұрын

Not sure where to go from here but I believe I found both insulations I believe for the transistor plate which I think is the issue for the smoking at least

@axelthefoxytechworld8024

Жыл бұрын

@@Treepadawan yeah that transistor needs it plastic insulator peice the metal of it canot touch ground

lol

@Mark-kq9ur

7 ай бұрын

Odd, you cleaned the old grease from the pinch roller assembly, but didn't re lubricate it before assembly