Thank you Eric

@EricDIY

22 күн бұрын

You're welcome...like and subscribe

Thanks a lot, literally had same problem

@EricDIY

4 күн бұрын

You're welcome...like and subscribe

Same issue dude finally got some relatable video

@EricDIY

2 жыл бұрын

You're welcome...like and subscribe

cheers mate. fixed my own one just now from watching 1 minute of this off google.

@EricDIY

3 ай бұрын

You're welcome...like and subscribe

@ThinkingBetter

27 күн бұрын

@@EricDIY Nice video. I have this exact same problem with an E-bike. I realize that this problem grows much worse when you bike with it being loose. You need to fasten the nut tightly immediately at the very first moment you notice it being loose or you end up having to replace the arm.

Thank you for this video! Your video confirmed for me that I had a wallowed crank arm. I had tightened the mounting bolt with gracious torque once I discovered the bolt was not torqued well. This almost got rid of the popping (knocking), but not quite. Because I bought the e-bike in February, I called the company for support under warranty. They have sent out to me a new crank set. No squabble at all.

@EricDIY

10 ай бұрын

You're welcome... like and subscribe

Appreciate the video - and the time and effort it took to make. Saved me and I'm sure other people even more time and effort even money- trying to fix my own/their bikes. RN my bike IS my transportation as I await fixing my jeep. So my livelihood depends on it. xo

@EricDIY

6 ай бұрын

You're welcome...like and subscribe

Thank you SOO MUCH MANN!!🙌🙏

@EricDIY

Жыл бұрын

You're welcome... like and subscribe

Having the same issuer on my beater bike. I’m just gonna try thread locker for now. Thanks for the idea.

@EricDIY

Ай бұрын

Probably won't last but you could try

Thank you this vidoe was very helpful

@EricDIY

2 жыл бұрын

You're welcome...like and subscribe

Thank you

@EricDIY

Ай бұрын

You're welcome...like and subscribe

Tip: you can use brake cleaner to clean the nuts and bolts and wipe it properly.

thank you so much

@EricDIY

Жыл бұрын

You're welcome...like and subscribe

Best way to remove a Crank Arm without the "Special tool" is to use a open end wrench (None Adjustable). Slide behind Crank and pull wrench outwards gently. Do this in a few spots and she should pop right off after a little Mucsle Power is applied 💪🤟

My bike squeaks while I’m peddling. It’s somewhat embarrassing. I was going to spray wd40 but now I’m wondering does it need replacing since it wobbles a lot

@EricDIY

2 жыл бұрын

Sounds like you need to replace or at least try to tighten the crank arm down

@tiffanychestnut6513

2 жыл бұрын

Thanks I took it to the local bike shop and he said it looks like it needs replacing but since he didn’t have the part in stock he tightened it. The squeaking was even worse the next day but today it’s gone. Thank at least I know what the fix will be if it returns.

How would u do this if the square bolt has no screw opening

@EricDIY

3 жыл бұрын

It might be under a cap. There should be a way to the extract it

Thanks so much it will really help me

@EricDIY

3 жыл бұрын

You're welcome...like and subscribe

My stock crank arm started to loose then i tighten it up again and it will loose for a very short period of time then i bought a new crankset bcos the stock was worn out but then i still have the same problem with the crank arm its starting to loose again even tho im tighten it up

@EricDIY

2 жыл бұрын

Did you use loctite? Is the screw the original and long enough to fully go into the crank?

What can I do I my bmx bike feel like it changing gear when I peddle or something and I tryed to tighten the bolt but the bolt is stripped what do I do to tighten it ??

@EricDIY

2 жыл бұрын

Get a new bolt and replace it. If it has a derailleur, make sure it is adjusted properly. If the crank arm is loose after replacing the bolt, try replacing the crank arm.

@Onewheeljj

2 жыл бұрын

@@EricDIY thnx

Do the left crank arm suppose to be tighten on all the way

@EricDIY

10 ай бұрын

It should be like I showed it in the video

im having this problem for a long time, always when i ride its starts getting lose after 1km, ive change from bb, crank arm, pedal, crank bolt but it still getting lose, any advice? i even tried super glueing it, but later got loose after 4km. the square that connects to bb is getting smudged and make the arm slightly slanted

@EricDIY

4 ай бұрын

If the square is rouding, buy a new crank arm like I did here. If rounded, it's past repair and you need to replace it.

I have watched now and I will try and say

@zq1921

Жыл бұрын

Did it work

@joel.ha.

Жыл бұрын

DID IT WORK? ARE YOU ALIVE

@leninsuriya5910

Жыл бұрын

Mm I am alive

@leninsuriya5910

Жыл бұрын

It's working well

@leninsuriya5910

Жыл бұрын

But why asking like this

when i put pressure on my pedals it rotates but doesnt move the bike, any help?

@EricDIY

2 жыл бұрын

Take it off and see if anything is broken where it attaches. It could also be the bearing inside being broken.

عالی بود - استاد

What torque?

my crank is actually wobbling. how do i fix it. my bike shop is telling me $160 to repair it.

@EricDIY

Жыл бұрын

Probably have to get the bearing replaced if it's not the arm. $160 sounds about right. As far as doing it yourself, there are videos on KZread but you also need some tools to push the bearing out.

@kevinhoward9593

Жыл бұрын

@@EricDIY its not the bearings but the part with the teeth that is bent.

Do we need a new arm

@EricDIY

Жыл бұрын

If the arm is damaged like I showed in the video, I would replace it. If it hasn't started to warp yet, you might get away with the old one. If it is warped, it will most likely keep becoming loose.

You’ll need a wrench with a long handle

@khodges2

2 жыл бұрын

This way you can get a pretty good torch on there. The quick tool will not be enough.

@EricDIY

2 жыл бұрын

You meant torque? I didn't have a.pronlem with the quick tool but I can see getting more torque with a longer handle wrench

Need a washer

@EricDIY

Жыл бұрын

There is no washer on this bike

Replacing the entire bike is not an option at this moment