HOW TO FIX A FLOODING WALBRO CARBURETOR
Автокөліктер мен көлік құралдары
Check out more carburetor related repair videos here ➡️ • CARBURETION AND CARBUR...
Check out my extensive amazon store
Chock full everything you need to repair
Small engines➡️ www.amazon.com/shop/backwoods...
Пікірлер: 30
Great video Jeremy
Thanks for the video.
Good video mm1 fixing that flooded carburetor
Most folks know how to do just the needle but that was the first video that I have seen on replacing the seat and using the special seating tool.
Thanks!
Thanks for the great video. I am wondering is this a repost of an older video?
Thanks bud. Carbs carbs carbs This time of year.
And for mine sense i made mine gravity fed which one should i use the smaller or bigger one
Had a guy call me ask if I could fix a Cub Cadet carb I said yes , But i rather replace it I can get one cheaper than a rebuild kit . gave him the price he said they make everything throughway today . yep price of the carb over labor rebuild .
We had a few of these come threw the shop where we ultrasonic the carb install the kit and still the carb floods. So after that we replace the carb.
@THEMOWERMEDIC1
2 жыл бұрын
I would replace the carb as well normally
@watcherwatchmen7785
Жыл бұрын
Some of them have a little needle sized air vent hole that can get plugged up. kzread.infoF0sjibeXe2Q. My carb didn't have the bleeder but I had to change the seat and tweak the little tab on the underside of the float so it put a little more pressure on the seat.
Simple. WOT and crank.
Is that the correct fuel filter for a gravity fed carb?
@mwreyf1
2 жыл бұрын
I noticed that as well.
Yo yo me old mucker.. ta very much for the video
@THEMOWERMEDIC1
2 жыл бұрын
Love ya old bean ol buddy
I would like to know the part# of that carb oem or ebay part # ,I am going to see if it will retrofit on 35 year old honda riding mower ht3810 they are NLA from all sources ,thanks
@THEMOWERMEDIC1
2 жыл бұрын
I have no idea what that OEM number is but I do know it’s off of a 287707-0115 - E1 Briggs and Stratton
@jimc1401
2 жыл бұрын
@@THEMOWERMEDIC1 Thanks for your time .with that engine # Idid find an Ebay retrofit carb with measurements.
My carburetor floods even though it seem airtight when I blow in the fuel inlet while holding the carburettor upside down.
I tried, still flooded. ended up buying a cheap knockoff carb replacement(for less than the needle/seat/seal kit) and it cranked up first try. had to change my oil after flooding it so much
Anyone know where I can get a rebuild kit for walbro lmj47 carburetor. It's on my Honda gx160 engine.
@gavinstandifer8880
Жыл бұрын
Just buy a new one
My mower won't start without a dash of starting fluid.
Some carbs you can't replace the needle and seat
@THEMOWERMEDIC1
2 жыл бұрын
That’s correct however this video does not cover those carburetors covers the replaceable needle and seat in a Walbro carburetor on Briggs & Stratton, Kohler, and some Kawasaki engines
Question? Why did they design the fuel solenoid with the tightening nut extra thin so you have to use a specalized wrench??? Seems stupid, but I am sure there must be a reason. Ha Ha
@THEMOWERMEDIC1
2 жыл бұрын
🤷😂
Its a cv491s engine and looks like the same carburetor