No video
How To - Enter the parameter menu and check the errorlog on a BT RR Reflex
How To - Changing parameters into a BT RR Reflex
1 Attach the CAN-key
2 Press and hold the direction switch.
3 Enter the Pin and press the green button
4 Release the direction switch when the letter P is displayed.
Use the Lift Lower joystick to adjust the parameter number
Press the direction switch the enter the parameter
Use the Lift Lower joystick to change the value
Press the Direction Switch to store the value
Log out by pressing the red button
video with description of all parameters here:
• BT RR reachtruck param...
More Toyota and BT videos in this playlist:
• Toyota BT Industrial a...
All Material Handling and Equipment video`s here:
• All Material Handling ...
Please support my channel,
Thank you for watching!
Пікірлер: 24
How do you set the time?
@1600GSI
Жыл бұрын
Press and hold the direction switch forward. Switch on the truck and release the direction switch when the T comes into view.
@1600GSI
Жыл бұрын
Open or close the parameter by pressing the direction switch, adjust the value with the lift joystick.
@IIFitz1
Жыл бұрын
That worked. Thank you.
I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition
@1600GSI
3 жыл бұрын
Main contactor K10 does not close when the truck is started and the emergency switch is inactive. 1. Defective contactor K10 2. Defective electronic card A5 1.Check the voltage in contact 808. Should be battery plus nominally + 48 VDC, with truck started. -If there is no voltage, check fuse F62 (10 A). -If the fuse is intact, check that cable 23 is intact. -If cable 23 is OK, check the contactor points on K10. -If the contactor points are OK, check that cable 1 is OK. 2.If there is a +48 VDC voltage at card contact 808 and the fault persists, replace the A5 card.
@Maystrenko22
10 ай бұрын
@@1600GSI Hello. Can you show where the Main contactor K10 is located? Where is contact 808? And where is the electronic card A5?
Cual es la tecla cam?
@1600GSI
9 ай бұрын
The CAN-key is a service tool that allows the user to adjust parameters and access diagnostic features on a BT forklift.
@JoseSoto-tr3nv
9 ай бұрын
@@1600GSI en mi trabajo hoy paso que apretaron el botón de parada y trae ese error no anda nada solo la luz la bocina y la dirección me podrían decir como se hace soy de Argentina Santa Fe gracias
@1600GSI
9 ай бұрын
2:580 Main contactor error. Main contactor welded. Check the main contactor, X131:7 and the wiring harness. Restart of the truck in the emergency mode position is nec- essary to reset the error.
Hello. please tell me what parameters 1-7 are responsible for?
@1600GSI
10 ай бұрын
Check out my channel for more BT videos. Here is the parameter list kzread.info/dash/bejne/d5OfyKZ-m7yYXZc.html
@Maystrenko22
10 ай бұрын
@@1600GSI thanks)))
@Maystrenko22
10 ай бұрын
@@1600GSI Why can only parameters 1-7 be changed? The remaining 11-42 do not change ((
@Maystrenko22
10 ай бұрын
c1 - time setting, P - parameters, Pn - ?, H - ?, E - error log What is Pn and H?
@1600GSI
10 ай бұрын
You need a CAN-key to change the value above parameter no.7
Used cankey
How ro reset bt reflux please video upload
@1600GSI
4 жыл бұрын
Please, be more specific.