The puller tool was the thing. Napa guy let me borrow his, and it worked! Thank you so much for the tute!

@Car-gpsdvdcom

4 күн бұрын

Thanks for your feedback!😃

Incredibly helpful. Got my replacement arm on and off in minutes. Thank you.

Thank you for the thorough and detailed instructional video. Changed out the wiper arm following the exact procedure and it worked like a charm. Much Appreciated.

Thank you for taking the time to do this. Would not have thought of the tape!

Great video! One little step suggested - I would double check that the resting position of the wiper tip does not land on the paint work that eventually would scratch the paint. The masking tape is a great step, but the arm might need to be positioned one spline to the left to safe guard the paint finish. (due to a little slack in the motor drive mechanism) Thanks for taking the time to make this valuable instruction video, very helpful!

Thanks - my arm was ripped off in the assembly-line car wash but they found the arm and spring. Freezing at 3:50 helped me identify how to reattach the spring to the two other parts of the arm assembly in situ.

Super helpful thank you!

I used the penetrant and tried to use an expensive puller, but the puller just broke the plastic. I finally took a small hacksaw and sliced the plastic away from the bushing, then used the puller to get the arm off. I bought an after market arm and blade. The blade, though an inch shorter, is easily replaceable unlike the OEM. Good video, thanks!

Huge help thank you!

Thanks🍺I replaced our Ford rear wiper arm by myself successfully.

@Car-gpsdvdcom

11 ай бұрын

Thanks for your feedback!

pretty good video, thanks.

@Car-gpsdvdcom

Ай бұрын

Thanks for your comments!

Yes, I did it. No problem however, had one problem. I put the wiper blade on the left-hand side when I put it back on and now I have to pop it up again. My fault I was in a rush

Let’s be clear. PB blaster only does its job on KZread!

I bent the arms on that tool trying to get mine off. It didn't work

⁰Thanks for the video. Subaru dealer service would not help me with this issue.

It's a 2012 chevy equinox

The snow broke my whole arm so it's just hanging. Do you know what I need to do to fix this????

@whatsup24_7

6 ай бұрын

A man

This was helpful, thank you. It took some serious effort though because it was corroded on there.

so um. what model car is this?

@Car-gpsdvdcom

4 күн бұрын

It is ford car.

What was the clamp thing called??

@Car-gpsdvdcom

27 күн бұрын

I will inquire with our staff, and then let you know, please wait again!

@iamjayyxx3245

25 күн бұрын

Yess I need it too, if you can send an Amazon link I’d appreciate it a lot

My dealer wanted 326$$

@Darkness-ie2yl

7 күн бұрын

you could buy a car for that

I just tried that, and that doesn’t work at all! Lol

@devinmcdonald2030

3 ай бұрын

It works. I just did it.

@Ont785

3 ай бұрын

@@devinmcdonald2030 Awesome! I bought another puller…easy peazy

@Ont785

3 ай бұрын

@@devinmcdonald2030 I will add, that it worked for you,,, I’m assuming you mean that should work for everybody? Lol

@olivertwist9628

2 ай бұрын

Put the nut back on the post get a hammer pull the arm away from the glass and slightly tap the post while turning the arm left and right do not smack the post hard enough to break the glass

@Ont785

2 ай бұрын

@@olivertwist9628 Thank you for responding . I actually bought a better tool that popped it right off . The old are the pieces, the harder it is to get off . Now I have a tool that I can use in another 15 years !! Lol Thanks again

Just what I was looking for 🫡