Thankyou for explaining how to deactivate childloc on my Boschk!! It was driving me crazy, thought the machine had packed up after only 12 months and worse, with a huge pile of holiday washing. Will refer to you in future.

@eSpares

8 жыл бұрын

+Jacqui Harnett Sorry I am late replying but KZread has just 'found' your comment. Glad to hear you found the problem. :-)

You guys have helped me out many a time, thanks for ya videos

Thanks. Will try your suggestion and check back.

@eSpares

8 жыл бұрын

Let us know if you need more help to identify the problem.

An overfilling washing machine is commonly caused by a blockage of grease and gunge in the pressure chamber, or more rarely a faulty pressure switch. Check for a hole in the small pressure chamber tubing

nice and informative video for diagnososing the washing machine.. thank you for your video!

@eSpares

9 ай бұрын

Hi, thanks for your comment. Nice to know you appreciate our video! Hopefully it helps you if you do have any of these washing machine issues.

Excellent video, thanks.

@eSpares

9 жыл бұрын

Cheers David, hope we have helped stear you in the right direction to resolve your problem.

Useful videos thank you very much and make each step by step defactive devices how to checking in the machine thank you sir,

@eSpares

6 жыл бұрын

We try to produce videos viewers can follow 'step by step' to fit the part r diagnose the problem.

After changing inlet valves i started to get f10 foult on aeg in begining of rinse. Is it somehow connected?

great tips thanks

Thank you that's very helpful 👍👍

@eSpares

7 жыл бұрын

:-)

Right, Thank you very much.

@eSpares

7 жыл бұрын

😊

Thanks for the useful vids. Our Bosch Avantixx 8 with digital display does not give any fault messages but blocks in mid cycle, flashing NO on the display. The cycle will then continue to completion by pressing the Start button again. I have run various programmes, some with no clothng in the drum, but the blockage and NO message reappear. Ideas?

@eSpares

8 жыл бұрын

Sounds like your machine is not heating the water and the machine is spotting this and stopping. Put the machine on a boil wash and see if you can feel any heat on the glass after ten minutes. If no heat see these other videos: kzread.info/dash/bejne/eKihms59hrndYqg.html and kzread.info/dash/bejne/goGNr8GjaLjVqc4.html

My main lower control board on my indesit blew and damaged a part of the control board so I got a replacement good second hand one but now it turns on and then the lights flash but jothing else, woukd you please let ne know what I should check next

Thank you sir

Thank you for this video. My washing machine has died. A Miele W844. It had been drawing power from a multi socket which had a kettle and a toaster running at the same time. I guess that is what caused it to stop. Lesson learnt, single power socket for the washing machine. Any tips on what I might do to get it up and running? Thanks.

@eSpares

9 жыл бұрын

Brett Champlayne Start by checking the brushes if the above video has not helped identify your problem.

got a miele novotronic premier w 500 drum not turning "rinse " flashing cant find model no in your list

I have a Zanussi ZWD1472 washer/dryer, starts to fill for a few seconds, but stops and wont fill or wash, will spin to empty. No error code displays Advice appreciated. appreciated

Hello, first of all, thank you espares for helping me fix my previous washer problem: the water inlet valve just needed to be replaced! Now, unfortunately, it's acting up again: I press start, it fills the soap box and then just a faint motor sound and nothing, won't continue... I've tried just draining it (by putting it on 'Drain' function and sometimes it has worked fine afterwards. But this time, draining it isn't solving the issue... Help?

@eSpares

8 жыл бұрын

+Lisa Reutenauer Hi Lisa, the two problems are not likely to be related. We have a whole series of diagnosis videos to help identify your problem. The most likely cause is worn motor brushes so we would suggest you start there with a video like this: kzread.info/dash/bejne/gJOmmsZyY9u2ido.html

Thank you for such an informative video. Our frigidaire affinity washer was working perfectly before we had a bad thunder storm. The power to the house was going off and on and we ran around the house unplugging computers, TV's, and my washing machine. The machine had power (the lights on the front were on) but we unplugged it anyway. Now it won't work, it only displays error codes, a whole variety of them. Do you think the control board has been damaged? You were mentioning something about fuses? Any help you give will be greatly appreciated. Thank you.

@eSpares

10 жыл бұрын

Hi Prariepatch, It is possible the control board has been damaged by a surge in electricity and this may be more likely if your supply passes through overhead power lines. However it may be due to components 'ageing' and not fully resetting after the power has been off. Follow the video again and if the machine does not reset and at least partially start the machine then you may need to replace it.

Hi, I have an indesit WIA111, about 11 years old. When I turn it on at the switch, before any program is selected (it won't let me) the inlet hose starts thumping, drum fills with water and the only way to drain it is to undo the lint trap. If I turn off the water supply and turn on the machine at the switch, I can hear a quiet thumping (possibly pump?) that continues indefinitely unless I turn it off again. I've emptied the trap, checked the inlet hose and filter, no idea what's happening. Any ideas? Thanks

w/machine keeps flashing 8 . hoover model H3W 68TME-80. I was told it might be the motor, is there a way of testing the motor.

thanks for videos

@eSpares

7 жыл бұрын

You are welcome, we have diagnosis videos to help identify faults on most appliances. See our new advice centre it can really help to find your problem: www.espares.co.uk/advice

Ok, and by control board and power module, you mean?... I know of the CCU central control board and the interface control board (the one on top crony behind the push buttons). Are you saying then to replace the interface board? Thank you so much for your help!!!

@eSpares

7 жыл бұрын

We cannot confirm any part if we are not working on the appliance. Fault tracing is often a process of elimination so it 'suggests' there is a problem with either the CCU or the interface boards (or possibly both). You could inspect these carefully for signs of burning or damage but often you cannot confirm a faulty part without replacing it.

hi, so the hose I mentioned in my last message was actually the pressure switch tube. Water pressure seems normal. Thanks for the video. What else could it be?

@eSpares

8 жыл бұрын

Try taking off the hose from the switch and blowing into the tub. If it is blocked the machine will keep filling. For more information see another video: kzread.info/dash/bejne/iIdomqmYk9qpiNI.html

Hi just wondering do you have a vid for replacing the dampers/suspension for a hotpoint I have an old wma56,,,,had to replace a top spring as it snapped...a friend suggested it may be the dampers over the bareing im keen to try and fix this first before having to resort to giving up my beloved machine ive had for ten years. thanks in advance

@eSpares

10 жыл бұрын

Hi areia511, The usual cause of a broken spring is an out of balance load making the drum move excessively (see: How to Prevent a Washing Machines Spinning Noisily ). However if you want o see a damper video we have a similar machine in a video at: How to replace a washing machine damper - LG

Liked very much this video. I couldn't find the short circuit though. It trips the safety switch after I finished set the wash program and press start. Normally I would expect the valve to open and water to flow. Regardless I unplugged the inlet valves or heater it trips at the launch the program. Not sure what elements the program starts before the inlet valves ? It's a lg wd-1049c.

@eSpares

8 жыл бұрын

+Thierry Lo Sorry I am late replying but KZread has just 'found' your comment. If the board trips your power as soon as the cycle starts and does this when the heater is fully disconnected the problem may well be the board itself.

Our machine keeps doing whatever it wants, including bleeping. Sometimes it keeps repeating the same action, sometimes, it tumbles but doesn't do the final spin., sometimes spins but the items are warm so I guess it hasn't rinsed even though it should within the programme selected. Not sure what the problem is, can you help?

Our problem with a Bosch Avantixx blocking with no fault message seems to have resolved itself without any intervention. If the problem reappears I will contact your helpful site again. Thanks for your advice so far.

@eSpares

7 жыл бұрын

:-)

@ddk3809

7 жыл бұрын

what is a ae code

@eSpares

7 жыл бұрын

What Make and model machine are we talking about?.

BOSCH washing machine has power on display but when selecting any programme it doesnt accept it just beeps.no error code shown.is it a controller fault?

The heating element on my Bosch machine short-circuited, and tripped the fuse. I replaced the element with a new one, but since then, machine has been behaving erratically. Once it reaches the end of each stage (wash, rinse, or spin), it thinks it has finished the wash completely, and the 'End' light comes on. I have to manually start the next part of the cycle. Could the control board have been damaged when the element short-circuited?

Superb! I now know it is the control board, but sadly it is AEG and only they can fit the board. So too expensive. Madding as it is only 4 years old and now going to landfill.

@eSpares

6 жыл бұрын

Hi L Bennie, anyone can fit the board and that's why we show replacing parts to fix themselves, check out our website www.espares.co.uk/search/ma143pt1980/washing-machines/pcbs-and-modules/aeg

My Whirlpool front loading washer that gives an E08 code, "if I clear the codes" it will do a half a dozen loads fine, then, fault the same E08 code. I can repeat that over and over again. I am thinking the mechanical water valves are working fine but the control board is the problem. I am curious what you think?

@eSpares

4 жыл бұрын

Hi Mark, check out this video that goes through Whirlpool error codes kzread.info/dash/bejne/Z5l_sMV_ksbHdpM.html

great video.

@eSpares

8 жыл бұрын

+Jim's picks Thanks Jim hope we may have a few more you would like to see:  kzread.info/dash/bejne/m5qLrZudlpTXl8o.html and kzread.info/dash/bejne/p392249yfqisZaQ.html

My AEG over a couple of washings stopped going to zero at the end of a cycle. The cycle would finish correctly and istead of 0 would display the start time blinking, ready to press start. Then one day it tripped my breaker and turned everything off. No error code could be seen as tripped as soon as turned on. I checked heating element, grimey and crusted, replaced with new. Now the machine turns on but when pressing start spells ERR in the panel. When pressing start and next button , then shows E66 --- which still is related to heating element ? How do I proceed from here ?

@eSpares

4 жыл бұрын

Hi HazeOverL, the ERR usually shows if the programme has selected correctly, the error code E66 will still be stored in the memory which is why it is showing when you press the buttons.

And if its tripping electrics but only a washer ? Replaced suppressor but still same thing thanks if you can suggest anything

@eSpares

5 жыл бұрын

Hi Kevin the most likelist componet to trip the electrics is the heater.

Hi eSpares, after some advice please mate, got a zanussi FJD 1466W, just doing a wash and then a loud click sound and it stopped, all lights except the power light have gone off, goes that sound like a new control panel replacement to you guys? thanks matt

@eSpares

6 жыл бұрын

Hi Matt, check the connections between the control board and the power module. If you cannot get two lights to display suspect the control board at the top of the machine.

Hiya, your videos are great!! My washer stop after about 10 mins, I have drained it by hand, and done the reset. The lights are on, on any programme , but its just not doing anything . Please were should I start first, also done the reset for error codes , but no error code comes up, please help!! lol cheers in advance.

@eSpares

8 жыл бұрын

+barbara townsend The first places to start are to check it can pump out by selecting 'Drain' if this is OK check the heater.

I have a problem with my affinity front load washer .. I have cleaned the drain pump it is clean , door lock is locked when on but it will not do the final spin it also has a little bit of water left in the drum. I'm thinking it's the control board , but I want to be sure. I checked the motor and the belt in the back all is good..

@eSpares

7 жыл бұрын

Before suspecting a control problem check the drain circuit and watch another video: kzread.info/dash/bejne/mKZ5rMqRabbWoNo.html

Hi, my 5kg direct drive LG front load fully automatic when spinning suddenly it goes off and sometimes in the middle of spin. And the next day i used it again all were good but after couple of days the same problem occured. Thank you in advance

@eSpares

7 жыл бұрын

Most LG machine show an error when a problem occurs, if the display also goes off and resets check the power connection to the machine. The problem may be due to a faulty motor sensor so suspect this if no other problem is found.

On my Samsung (wf45H6300) front load washer (US), I got the HE code several times and then starting getting the AE6 code. The heater element seemed ok at a little under the 27ohm spec--about 17 ohms if my meter is calibrated correctly This problem happened eventhough I wasn't using steam and have hot water going to the washer. Should I replace the heater element anyway? If that doesn't work, then replace the PCB (panel control board?)?

@eSpares

6 жыл бұрын

Hi Harold, the reading you got from the heater would suggest it is ok, HE refers to temperature sensor so check that first, AE6 refers to a communication error between the boards. Check the contacts and any signs of damage and good luck.

What if you get no error code? My Indesit WIXLwill not start- when I switch power on, horiz & vert lights flash once & red door light flashes continuously. I select the program & press start & the corresponding vertical light comes on. When I press 'start' button, single vertical light stays on, door light goes off and nothing happens. I have replaced door lock with no result.

Hi, great info, thank you. I have a problem with my Hotpoint HF8B593G. The programming knob just goes round and round and does not change the programme but machine is working but only in one mode, the last one set I think. I was just going to buy a knob from you and replace?? Could it be that simple???

@eSpares

9 жыл бұрын

Hi Sue, This is a common problem with your model where the shaft socket on the knob breaks and no longer moves the switch (see the third image on the part www.espares.co.uk/product/es1636443/). You may have to remove the control panel and PCB to release the old control knob before fitting the new.

@burgesue4117

9 жыл бұрын

Hi thanks for that. What's a PCB?

@eSpares

9 жыл бұрын

sue burge Have a look at the following video, although for a Hoover machine the repair method is very similar. How to Replace a Hoover PCB and Timer Selector Problems.

Hello my Samsung washer was made in Mexico, do I have to get part from Mexico e.g. control board to replace it.

@eSpares

8 жыл бұрын

We can get spares for most models as long as we have your full model number. Before you suspect a faulty control board we suggest you watch our diagnosis video to identify if the problem is elsewhere: kzread.info/dash/bejne/g42E09KjfLmdo5c.html

It seems to be a door lock fault on the control panel on my Zanussi machine. Is the control panel reasonably priced to replace or am I better off getting a new machine? Most engineers in my area cost £50 just to come out and look at it. The machine itself cost £300 roughly when I bought it 5 years ago.

@eSpares

4 жыл бұрын

If you click bit.ly/2lzjcsu & fill the online form, we can verify availability with our suppliers & update you directly

Hi i have a Bosch Maxx Classic front loader. in the panel its showing me E2 can you tell me what that is please

@eSpares

8 жыл бұрын

We have another video on Bosch error codes that explains F02 here: kzread.info/dash/bejne/gqp-ztOImqqchcY.htmlm46s As you will see the problem is likely to be a heater problem, replacement on elements fitted from the front is shown here: kzread.info/dash/bejne/goGNr8GjaLjVqc4.html

Amana model NFW5700BWO. We were getting a clogged drain line code so we cleared it out and when we went to plug it back in it makes noise like it's trying to go through a cycle but the power isn't on and won't come on when we push the power button. The door is not locked and it still makes the noise with the door open.

@eSpares

6 жыл бұрын

Hi Cammi, you need to check if you have a leak detection float in the base of the machine if this activates it will continue to pump all the time even when off. Check for a leak before suspecting anything else.

what are the pink and blue balls for in the intro?

@eSpares

7 жыл бұрын

Hi Fiona, they are tumble dryer balls (www.espares.co.uk/search?SearchTerm=dryer%20balls) and they help reduce tumble drying time. 😉

Hi I have a Hotpoint Ultima washing machine thats about four years old and the machine has recently started to smell on further investigation it seems the water is not heating up it just washes cold no matter what the temp setting is but the machine shows no error codes and washes without pausing through its cycle although it does seem to wash a alot quicker than the time on screen suggests I imagine because the water is not heating up is this possible without error codes ?

@eSpares

4 жыл бұрын

Hi Iain, if the electronics have not detected an error it may not be displayed but if it is not heating then you need to test the heater with a multi meter to determine if it has failed and the video shows you how at 7.05

I have a Siemens i890 (approx 5 yers old) that is not turning on. When it does the screen is blank but the machine is operating fine. Is this one of the power Boards?

@eSpares

4 жыл бұрын

Hi Stu. it is likely to be the display board, check for any signs of burnt contacts or damage.

Hi I have a 13kg Samsung fully automatic top loader washing machine model number WA13G7Q1 which stopped working.The technicians told me that my control/computer board is faulty and need to be replaced.They can't find such a part as it is "old tech" and is no longer available on the market.Can you please help find this control panel/computer board or indicate to me where I can find the part.Thank you

Hello, how can i reset a washmachine AEG L60800? I get sometimes an error code E50. Thanks for your help

@eSpares

10 жыл бұрын

Hi Georgios, Error E50 suggests an intermittent motor fault so check the motor plug and connections and if these are OK check and replace if required the motor brushes. This machine should not require to be reset after repair.

@lindakobere5851

6 жыл бұрын

Hi. I have an LG 12 kg WD-T12415D washing machine that seems only to perform the drain function. It always brings an error code E64. How do I rectify this or how can I do a factory reset.

if i find i have continuity from plug to circuit board, can i assume the filter is fine???

@eSpares

6 жыл бұрын

That is correct Ray unless the power trips or blows when the appliance is plugged in.

I recently replace a door switch on a frigidaire front load and I fix the problem. on the other hand I started the washer cycle and everything went well until an alarm sounded and would'nt stop but, the washer contiue to work properly. How do I stop the alarm sound or buzzzer sound.

@eSpares

7 жыл бұрын

The alarm sound would normally indicate a problem that has been picked up by the control board, try unplugging to see if it resets.

I have a zanussi ZWF1237W which stopped a wash at the rinse stage and showed an E20 fault. As per instruction manual i cleaned the pump and removed a piece of material. Each attempts at a wash still stops at the rinse stage. I can fiddle around with the knobs and get it to do just a rinse. Please can someone tell me how to do a reset to clear the E20 and get the machine to do a complete wash, rinse, spin cycle as before. (I have tried leaving the machine switched off at the mains for 24 hrs.)Grateful for any suggestion. RB

@eSpares

6 жыл бұрын

Hi R Burhouse, To error code is stored in the memory and can be removed if you enter diagnostics to clear it but you don't normally have to if you are still getting E20 then you still have an issue with the draining cycle. Check the drain pump impellor and test the pump with a multimeter first, check for any blockages inside the hoses that may be stopping it from draining.

The presenter speaks very clear English.

@eSpares

8 жыл бұрын

+alex Lo Thanks, we try to make our videos as clear as possible.

HI, is there a video about how to replace the circuit board on a Zanussi washing machine?

@eSpares

5 жыл бұрын

Hi Lumi, we don't have a video at the moment but where is yours on the machine and we can help.

my beko machine is stuck on the same wash. when i turn the dial for a different wash the display wont change. luckily it's stuck on a 30 wash and does still wash ok. but the display has some info missing off it that usually shows up before you start a wash. help.

@eSpares

8 жыл бұрын

+Elsie Hannam Check the heater has not failed as the display may be trying to indicate a problem. If you cannot 'turn' the timer to drain or spin it is likely the control knob is not engaging with the control.

Hello, i have washer dryer AEG 3 years old, model L61271WDBI, is triping my fuse when i starting and i can not turn on the fuse until door lock is release.

@eSpares

5 жыл бұрын

Hi Liliana, the most common reason for a washing machine to trip the electrics is due to the element failing so start there, you will need a meter to test the element and this video shows testing the element kzread.info/dash/bejne/eKihms59hrndYqg.html&t

hyia i have a AEG LAVAMAT L14800 washer dyer and everytime i put it on a wash i returns to a 3 min drain wondered if anyone can help its not going though any wash cycle at all

@eSpares

8 жыл бұрын

+chantele wyllie Your type of problem is the reason why we made this video as at first glance you cannot see a problem. You need to watch what is happening with the cycle so for example it sounds like it fills then stops filling and starts to wash moving the drum. If this is definitely the case then the most likely problem is going to be the heater so check out this video: kzread.info/dash/bejne/eKihms59hrndYqg.html

Hello JOSH My washing machine samsung, model WA90F4 is not powering on,the problem started with the buttons not responding well and now is not even switching on.

@eSpares

9 жыл бұрын

+buzo steven 'Not responding well' is a bit vague. If you mean the appliance did not light unless you 'fiddled' with the switch or turned off and on a few times it may be just a damaged switch. Turn off and examine this as there will often be signs of damage.

Hi Josh. Great videos mate! Got a question for you. My LG washing machine will not de power the water inlet solenoid, so it just keeps filling. Pressing the power off button does not stop it either, only pulling the main plug out of the wall! So I'm guessing it's PCB problem... Is there any sort of reset or anything else I could check that could be causing this problem.

@eSpares

9 жыл бұрын

Sorry Gerrard, Unless there is signs of spillage or damage to the wiring loom it is likely to be the control board that is faulty. :-(

@Aurora..Borealis

9 жыл бұрын

Damn i thought so... Thanks anyway you're a good man!

@eSpares

9 жыл бұрын

Gerard De Waal :-)

PLEASE could you please supply or do you have a fault code list for a Zanussi fle1216w?

@eSpares

4 жыл бұрын

Hi john, what fault code have you got?

Hello I have a whirlpool awo/d 5556 I put on a wash this morning all was fine thought the cycle had finished but drum full of water, it had taken the powder but still fabric conditioner still in the draw. I go to switch machine back on and there is no power. I have changed the fuse and tryed other appliances in the socket which all work fine. Just the machine has no power what so ever, also the machine door is unlocked but still full of water.

@eSpares

8 жыл бұрын

+LISA PENKETH Sorry I am late replying but KZread has just 'found' your comment. It sounds like the control panel has failed but check the plug fuse before replacing.

hi, need help...I have a Samsung washer front load. It is overflowing with water when it fills. Already changed both hot and cold water valves, pressure switch and hose. Could it be possibly the control board? Thanks!

@eSpares

8 жыл бұрын

A common problem on some Samsung's is the tube to the pressure switch can rub on the tub during spin and get a hole. if this happens the air that is pushed up the tube to turn the switch off when filling escapes. The machine thinks it has not enough water and continues filling. Check the hose for damage and for more information see another video: kzread.info/dash/bejne/iIdomqmYk9qpiNI.html

hi i have a beko wma 510 w.. the drum wont turn.. ideas what the problem coulf be... much appreciate an input... tnx :)

@eSpares

9 жыл бұрын

Hi 35Emamalou, check out another video: How to diagnose washing machine motor problems this should help identify your problem.

Argos made ProActionA105QW washing machine. After program selection and start,it mostly tries working by giving a soft-sound and nuttin happens thereafter, and it displays a binking START light. Any help? eSpares

@eSpares

9 жыл бұрын

Jibbie odutoLa The sound is likely to come from the valve that the fill hose is connected to as it is powered to let the water in. If the water is not flowing check the supply hose and water pressure by taking the hose off and filling into a bucket. If there is not enough pressure (should be difficult to stop pushing a finger over the end) then the machine cannot fill.

i have a Beko WMY71023LMB3, it all happened on cottons 90, the machine would start the heating stage then at a certain amount of time it will abort turning all the leds off keeping 60 degrees and 800 rpm on, if i pressed any of the buttons my settings would be restored but the machine has to start from ground zero but then to end the cycle with end light on and doorlock flashing, same thing happened to 40 as well, thanks in advance note: other programs work just fine and so does cottons cold

@eSpares

6 жыл бұрын

OK a couple of things to check. Can you feel any heat through the door glass?, If not check the heater. If the glass is very hot suspect the thermistor in the centre of the heater. See our video: kzread.info/dash/bejne/eKihms59hrndYqg.html

@eli55121

6 жыл бұрын

eSpares it heats perfectly on a different program at the same temp, i am wondering whether it was the selector or PCB

@eSpares

6 жыл бұрын

It is possible but most times a problem like this is not the control board. We would start with the sensor as this will be a lot cheaper than the control board.

@eli55121

6 жыл бұрын

eSpares what's the job of the sensor? And how does it look like? Is it built into the board? Sorry for all the questions, i always had timer machines

I have LG front load. It runs a bit and has a LE code. Please give me an advice. Thanks

@eSpares

5 жыл бұрын

Hi Nhạc Tình, Error code LE means the machine has detected an issue with the motor, start by checking the door lock and wiring and check for cracks in the magnet in the motor. Test the motor with a multi meter.

Hi my zanussi zwf1600w washer is not working. I have managed to get an error code 40 so I changed the door interlock part but it's still not working. It comes up with the start of programme time on led but then all lights go out and led changes to 0 as if cycle has ended. Any ideas?

@eSpares

7 жыл бұрын

Once the machine detects 'an error' it will shut down. Have you checked all the lock connectors are tight and not burnt as this also could be the problem. If these are OK it may be the control board. You may have to replace this to prove if faulty or not.

I have Lg washer and the connector from Main board panel to front control panel are burnt, how do I check if the main board or the control panel board are good. thank you

@eSpares

5 жыл бұрын

Hi sunsteve1, you cannot meter the PCB but check it visually for any signs of damage, if the connector is too badly burnt you would need to replace it.

I have a Beko WMB 71442W. When I turn the dial to select the program I want the display flashes and it jumps between a number of different wash programs. It takes several minutes to be able to select the program I want as just as I select the spin speed and temperature I want it jumps back to a different program before I get a chance to start the wash. Very annoying, any idea what this could be?.

@eSpares

7 жыл бұрын

The problem is likely to be the selector switch: www.espares.co.uk/product/es1545970/

Hi I have a hotpoint wdl 520 keeps switching of through all programs not displaying anything just switches off had a guy look at it and he said it was in good order but still got the problem he said would take it away and sell me another one it works sometimes should i replace the board or the washer any help please

@eSpares

7 жыл бұрын

Hi, the PCB cannot be replaced by anyone other than a Hotpoint engineer or their agents as it needs programming to work at all. If you follow this video and everything else seems OK the choice is to have an engineer replace the board or replace the machine.

My washer will agitate with no load in it but will not agitate with a load. Any help?

Hi ther so I have a indsent washing mashine that's got f11 however I had a plumber come out to look at the isue he sed everything is working fine but the problem he had found was the mouther bourd is this something I can fix my self do u sell the part and is it a quick fix or do I need a new washing machine

@eSpares

7 жыл бұрын

Hi Kenneth, a control board is unlikely to be the problem. Our video: kzread.info/dash/bejne/k6mYk5aCYL3babA.html explains that F11 is a drain problem so watch this video to identify what is going wrong: kzread.info/dash/bejne/mKZ5rMqRabbWoNo.html

@kennethwilliamson3937

7 жыл бұрын

Yea I did that and had a person come look they sed it was the bourd

I ha an LG Washer, Model WM2688HWMA. I recently replaced the bearings which also involved replacing the rear outer tub, the old one had cracks around where the seal should go and would not allow it to snap into place. I did clean the inlet valve filters while I had the hoses off. Within the first couple of days, we had an FE code which sounded the alarm and we caught it in time to avoid problems. Today the front door on the washer burst open with water going every where and lots of water still in the tub so I figure it over filled. There was no alarm though. Question(s), what should I check, the inlet valve(s) or the water level control or all of the above. Or just replace these items? One thing, the top hose (largest one) had a different part inline than the original which was mushroom shaped.

@eSpares

9 жыл бұрын

Karl Rolling Ok lets think about this fault logically If the machine has shown an FE error it knows there is too much water in the drum so pressure switch and hose are OK. That leaves the fill valve sticking (easiest and cheapest to replace). or possible the control panel. If the problem is not cured by a valve then the board would likely need replacing.

@kmrolling

9 жыл бұрын

What about the dispenser drawer? There was water still coming through it? Just trying to cover my bases!

@eSpares

9 жыл бұрын

Karl Rolling The water passes through the drawer but is not controlled by the drawer so it cannot cause overfilling. If water is leaking out of the drawer it is caused by a blockage of either the spray jets above or the outlet pipe below.

You are amazing

@eSpares

5 жыл бұрын

Hi Ryan, thank you for the compliment and remember to keep watching.

I have a bosch 1400 exxcell washing machine that will not complete the cycles. If I put it on a wash cycle it will fill, wash for 10 mins and then drain. If I put it on a rinse cycle it will fill and rinse for approx 5 mins and then drain. If I put it on a spin cycle it will drain and spin (at low speed) then stop. On all when it drains the display will go blank. No error code is displayed. I have checked the filter and drain hose and there are no blockages, pump is working as it is pushing water during the drain cycle. Any ideas?

@eSpares

9 жыл бұрын

Hi John, try on an empty spin cycle to see if it will spin up to high speed. If it appears to splutter as it turns then that would indicate worn motor brushes. If no other fault is found suspect the heater element before the board as it may identify a faulty element and shut down.

@jasonhounsell3297

9 жыл бұрын

eSpares Hey, I don't know if you guys have done a video on hoover/candy machines, I used to work for them as a service engineer, I watch a lot of your video's just to see other machines as I do as many as I can in my spare time and repair them, if you want some info on some of the machines and common problems and fixes for hoover/candy machines let me know, or if you have had any unusual problems --- we had countless unique faults with the machines which required some fixes from standard --- I.e the aqua tumble dryer doors continually warping and melting --- add a thermostat to front --- E7 on integrated washer dryers was a manufacturing fault with the boards when the door wasn't opened in time and locked door. The oddest one which no-body figured out and took myself and my friend who worked for them also 3 visits and 5 hours to finally fix and a lot of company money, which was a drain issue, easy huh? For some unknown reason (Pity I can't remember the model now) the drain pump would cut out every so often, ok.... perhaps its faulty when worked too hard, replace it right? nope... No insulation fault with or without water, ok.... replace the board.... Nope.... hmmmm After finally finding that the drain pump was getting only 120volts at a certain point in the cycle this made you think clearly the pump wasn't a problem, but surly the board that isn't giving the correct signal, but its replaced! It was somehow.... the selector switch.... no idea how, tech team had no idea how, no-body knew how, but then a few of us ran into same problem and sure enough the fix was .... the selector switch....

@eSpares

9 жыл бұрын

jason hounsell Hi Jason, Thanks for your comments. I remember only to well how the programme selector switch plays up on a number of Hover/Candy machines and arranged a Video showing the replacement and advising of the problem. Gues it was just the connections going resistive causing the CPU to think the cycle was not selected correctly. On a quick note of 'pausing drain pumps'. I to have had a number of Hoover/Candy machines when after 20 to 30 seconds draining would pause for a few seconds then restart. I think this is just part of the programme when the CPU checks if the cycle has finished and if the pressure switch does not report empty it starts again. I don't think it is a problem so if you see it again there is no need to worry..

Hi josh, we have a Beko 71642 which decided to stop on a rinse&spin cycle, I have checked as much as possible but it will not continue . I then went on to check the Code error which reads 1510 can you please tell me what this relates to. the solenoids are working, the pump is working, I have checked the brushes on the motor and they are ok , I put it on 1 cycle and heard the heater start so I don't think its that, please help.

@eSpares

8 жыл бұрын

+Richard Dyer Hi Richard, do you mean the machine washes but does not move on to rinse/spin. If that is the case the machine is not identifying any heat so either the sensor or the heater itself may be faulty. If the machine is not washing you may have a motor fault. See our motor diagnosis or heating diagnosis videos.

Hi I have top load fully automatic smsung washing machine .It stopped working the start /pause button . All the other functions are ok .What should i do

@eSpares

8 жыл бұрын

+D.N.D Liyanage You need to first work out how much of the machine is working. Start by watching another video: kzread.info/dash/bejne/g42E09KjfLmdo5c.html

I have no lights, wont power on no clicking. mechanically it was fine. It completed a cycle. then when I went to unload it the door was locked, machine was not lit up like it normally has a clean light lit. i had to unscrew the bottom and manually unlock it, which I did to unload the machine, now I still have no power at all. Ive tried all the 'resets', plugging it in unplugging it. no click noise when I plug machine in. I don't know if I should replace the interface control board or the central control board, any help is appreciated.-

@michaelobrien8809

6 жыл бұрын

Faith Cooke has

programme selector knob on my Zanussi ZWN 7120L is stuck how do i fix this or replace same if required. machine is n off position knob will not rotate

@eSpares

6 жыл бұрын

To identify the exact knob you will need to go to our web site www.espares.co.uk/ with your production number (starts 9149?) from the label under the door as there are a number of different versions of ZWN 7120L. Our live chat should help identify the part.

Hello, Our Bosch Avantixx 8 (3 years old) stopped in mid-cycle without an error code. The door will not unlock. Any suggetions on how to proceed? Thanks very much.

@eSpares

7 жыл бұрын

If it stopped full of water see another video: kzread.info/dash/bejne/mKZ5rMqRabbWoNo.html if it was empty see this: kzread.info/dash/bejne/g42E09KjfLmdo5c.html

my 5.5kg Simpson eziset washer has no power have they got a fuse or is it control board

@eSpares

7 жыл бұрын

This machine is not familiar to us but we would suggest you disconnect and follow the continuity of the power cable to any control board using a meter as shown in another video: kzread.info/dash/bejne/on6f27txobW4p8Y.html

What if the board has been already changed but when we try to start the machine it starts to smell like a burning rubber and it starts not to work anymore. The board was changed twice already and the same thing happened. What do you think is the problem of the washing machine in cases like this?

@eSpares

4 жыл бұрын

This could be any electrical component in the unit causing this , possibly the wash heater. Only way to confirm would be using a megger and checking for any lower insulation readings than expected.

Hi, my Hotpoint 9575 is rather old but I've kept it going with your spares. I came back from holiday last week and put my first load on only to return ten minutes later to the machine having filled, but just emitting a buzzing noise. From experience, I concluded it could be the brushes so I replaced them, albeit on removing the old ones, they did have a good cm left on each. Anyway, on starting the machine again, with no load, the drum filled and it began to spin. Success I thought. However, on loading the machine with clothes, the machine filled, but then did no more. Any ideas would be welcome please. It won't work in any programme but will drain. Thank you.

@eSpares

6 жыл бұрын

Hi Nick, check the drive belt and ensure it is tight on the pulley. Test the motor and this video will help kzread.info/dash/bejne/dml12Zl8cqitgKw.html

@nickwalton8864

6 жыл бұрын

Many thanks. Re checked everything and other than clicking it in manually on the agitate mode, it then ran better than ever and the click is heard between each cycle. Fingers crossed. 😊

Hi, I have a Whirlpool washer Model# WTW57ESVW1 that seems to be out of cycle. When you first start a cycle it usually fills with water first ,then goes into the wash cycle. My washer starts to fill and agitates immediately. Then when it gets to the spin cycle, after spinning it stops and then begins to fill with water as if it were starting a wash cycle. Any help would be greatly appreciated. Thank you

@eSpares

9 жыл бұрын

+Bill Martin If this is a new washing machine it may be that the machine has been programmed for these little quirks. For example many machines 'weigh' there load by turning the drum and stopping to work out how much water is required and most will rinse spin and rinse before another final spin.

Is there a simple way to reset a control panel? I have a Kenmore he washer front loader. Some how the panel reset itself. The cycles are now under a minute long, the panel does not display water temp options. I have already unplugged it overnight in hopes this would work, but no go.

@eSpares

7 жыл бұрын

Hi Lori, the control panel is likely to be resetting each time the power is off but you may have a problem causing the cycle to stop. If the machine does not finish filling or shuts off immediately filled watch this video: kzread.info/dash/bejne/iIdomqmYk9qpiNI.html

Hi espares. So my Bosch Classix6 washing machine keep throwing up f21 error code. The machine drum turns easily enough by hand but will not spin. Even when empty and set straight to the spin cycle it goes straight from 12mins to 1min and does nothing. I've just replaced the brushes and still the same. Please help!!

@eSpares

5 жыл бұрын

Hi christianiani, F21 does normally refer to a motor error with the carbon brushes being the issue, were the carbons worn when you replaced them and did you reset the error code? you will need to test the motor and it could be the board causing it.

@christianiani

5 жыл бұрын

@@eSpares Thank you for your reply. The old brushes were just over half worn when I replaced them. Cleared the f21 code and tried again. But same error code flagged back up. I looked on your site for the price of a PCB and decided it wasn't worth getting one as the machine was 2nd hand 5 years ago when we bought it!! Oh well 🙄

Hi there i am having a problem with my machine, it is beko ev5100+, the problem was with the pump, i replaced it, and still it do not put the water out, i have opened the electronic cirquit, and a triac was broken. But i can't find another triac like that, it's code is z3m g f338, i changed also a rez that was burned. Pls can you tell me where i can find another triac like this or where i can search for another cirquit ????

@eSpares

8 жыл бұрын

+ledjano cela Unfortunately the manufacturers do not make this information generally available and an engineer would simply replace the panel. If you wish us to quote for the cost of the part please fill in the information at the page this links to: www.espares.co.uk/contact/sales

I have a Hotpoint Aquarius WML540 - program won't start - all lights go out except start button light which stays on (green) - no flashing lights - is this a fault code zero or a fault that cannot be identified by control board? Any suggestions would be appreciated.

@eSpares

9 жыл бұрын

Hi Chris, a couple of checks I would make is select a drain cycle and see if the door locks correctly. Check the drain pump is not blocked or damaged and finally check the main motor brushes and heater with a meter for continuity. If all check ok it would suggest a board, as mentioned these may not be replaced without having to be programmed.

Hi, my LG washing machine play button is not working. All other buttons work properly except the play button. I also notice that if I hold down the play button for about 5 secs some lights will start blinking. What do you think the problem might be?

@eSpares

5 жыл бұрын

Hi Olaiwola, you need to determine if the button has failed or possible the board, gain access to the control panel to check.

Hi I have a Hoover DYN9144 DG washing machine and for the last few weeks the program has not been working it's always switching from different programs making the wash cycle go on for longer. Now the machine is not showing anything but there is power. Please help!

@eSpares

5 жыл бұрын

Hi Naomi, test the connections to the board and check for any signs of damage on the board, unfortunately, you cannot test the board so you need to eliminate everything else before you decide it's the board even though it does sound like that is the problem.

I have a Kenmore Elite 41473210 washer that turns itself on and then beeps (reminder) to start the cycle. If we unplug the machine and just plug it in when we wash it will cycle through fine and shut off- several minutes later it turns itself on and starts beeping. No fault codes. I'm guessing one of the boards is going bad? any suggestions?

@eSpares

8 жыл бұрын

+almost genius It is more likely to be a heating problem if everything else appears ok. If the machine fails to heat the machine may recognise this and shut down. For more information see some of our Diagnosis videos in the following section: kzread.info/head/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ

whirlpool duet steam model number wfw9550ww00 I start cycle lights go on it counts down like it is going though the cycle but it is not spining or calling for water, door stays locked until I unplug then plug back in and wait for about 5 min

Hi, My samsung J1255A 8 KG Front Load SilverNano washing machine drum shaking too much and hits the walls of the machine while washing and spinning. what could be the problem.

@eSpares

7 жыл бұрын

The problem is most likely to be what you are washing not the machine. Don't worry we have another video that shows what we are on about here: kzread.info/dash/bejne/p392249yfqisZaQ.html

Could you tell why my washing always container water or drainage it works fine it just after washing after 8 I find in the cycle please help ?

@eSpares

7 жыл бұрын

If the machine has water in it after a while but drains correctly check if the water is returning through a hose connected to the pipes under a sink. If this is the case raise the hose so water does not flow back when emptying the sink.

Hi, I have a washing machine samsung WD-B1255 and when I use a high temperature, some times I have an error "8E". I read in the machine manual and I saw this error referred to something related to a thermistor. I replaced the thermistor, which is situated down with the heater, but the problem continues. The washing machine has another two thermistors which are situated on top, where is the drying system, but I think those two are for drying system and they don't involve in my problems. Please help me whith any solution Thanks in advance

@calinmadescu7798

10 жыл бұрын

***** Thank you for your clues, I will check the control panel.

My Whirlpool Washer (Model #WFW9150WW01) will not start when I push the start button. The wash light below status flashes 3 times then 2 times while beeping the same amount of times. Any suggestions on what might be the problem?

@eSpares

7 жыл бұрын

Hi Robert, this error usually occurs when the machine has not drained correctly so check there is not a problem with a blockage or the pump. If this is OK it may be a pressure switch problem, this identifies the water level in the tub and if blocked can think it is still full. For information on this see our video: kzread.info/dash/bejne/ZKR9uM16qLq5iMo.html

I have an older LG front loader that keeps giving me a low water pressure message. It won't fill after weight sensing.

@eSpares

7 жыл бұрын

Watch another diagnosis video for more information: kzread.info/dash/bejne/iIdomqmYk9qpiNI.html

Hi eSpares, I have a LG front loader washer which won't go into the short spin before the rinse cycle, so after the wash cycle the water is drained then the washer just come to a halt for one minute before filling the water for the rinse cycle. What do you think it could be the problem?

@eSpares

7 жыл бұрын

Hi Bonnie, try on an empty rinse and spin cycle to see if it will work?.

@shed0175

7 жыл бұрын

It works fine on a rinse and spin cycle even with clothes inside, only the Quick and Intensive cycles (the two cycles I use most often) won't work. The washer was overfilled with water right before playing up like this, I fixed the problem by reconnecting and untangling the hose.

@eSpares

7 жыл бұрын

Check the water heater element as if this fails the machine may stop and give an error code then may empty and rinse.