This video is really all about trying to get the best possible results and outcome for a small stone chip, for those of you that have a little experience under you’re belt. However if you’ve never touched up, sanded or corrected automotive paint in the past, this really isn’t the best starting paint, as there is a learning curve we all need to go through before getting to this stage. The best way to safely buildup your skill set is to grab a cheap car panel from a car wreckers and use that to practice on before attempting it on your beloved car!

@artscrimo5396

3 жыл бұрын

Great Video...

@nighthawkj30A4

3 жыл бұрын

Ive used those Duplicolor touch up paint pens that have both. Bruch and plastic pen with clear. There ok but no means perfect this is the best method i have seen. Also i use Various Meguires Ultimate And Gold Class Products on all my cars paint.

@unknownknown8555

3 жыл бұрын

Thanks for making this video! Question though.. When painting, if I go outside of the chipped area a tiny bit, should I sand lightly to remove the paint or just continue with the process? It’s difficult to stay perfectly inside the area missing paint so I’m curious what you do if you end up going outside a tiny bit.

@CarCraftAutoDetailing

3 жыл бұрын

I’d use some thinners to gently wipe it off an start again. Unless the paint is too thin, it really should sit inside the chip as long as you just dab the paint into the chip.

@TheNewFaceOfHSP

3 жыл бұрын

I subscribed because of the honesty in your video. I'm a DIY mechanic and have done a little "make it acceptable" paint correction, recently bought a (factory) new yellow car, and it got a stone chip. The part where you said "It will never be perfect" and admitted you don't always do this either, made me realise, that I'm just going to do a basic touch up with cleaning, base coat and clear coat, and not bother wet sanding, as it will have me need to re-polish a 2 week old car. Not worth the effort. It can get this treatment, and then a yearly polish if I'm not satisfied. Thanks for the honesty.

I did this to my 2015 Reflex Blue Mazda 6. After 3 days of hard work and effort it did not turn into a Red F430 Ferrari.

@Dosbomber

5 жыл бұрын

You did something wrong somewhere... my 12-year-old Jeep Wrangler turned into a brand new Lambo.

@ichoozjc

5 жыл бұрын

Because you put red touch-up paint on your blue car. Duh.

@GOOSEAF

4 жыл бұрын

You see your problem was you weren't quite holding your mouth right and you were breathing on the offbeat, otherwise you would have had an F430 with a manual transmission, in Ferrari red no less. We just can't seem to get you kids to get it right. Oh well, maybe on your next pass. Wear these, 🕶, and at least you'll look cool until you get it right. Bare minimum you should have come out with a 308 GTB.

@denniss4724

4 жыл бұрын

why do people buy Mazdas smh

@jw8553

4 жыл бұрын

Lmao

This royalty-free music had me thinking Ron Jeremy was gonna stroll out and do the buffing.

@richardsmith1971

3 жыл бұрын

😂😂😂

@Agrillot6

3 жыл бұрын

With his bush lol

@1detroitmuscle

3 жыл бұрын

💀💀💀

@marsh2031

3 жыл бұрын

Lol....classic

@TheRhythmReview

2 жыл бұрын

🤣🤣🤣🤣

Some notes: 3:00 marking chip to be repaired with wax pen 5:00 wet sanding around area with, 1500 for hard paint or 2500 grit for soft paint. Until surface is smooth 5:25 Thinners to clean area 6:05 apply base colour with small brush or toothpick 7:40 clear coat 9:35 sanding 10:00 fine sanding 3000-4000 grit 10:45 polish/compound. for soft paint: medium compound on foam polishing pad

@CarCraftAutoDetailing

3 жыл бұрын

Well done, nice work!

@faazilvally626

3 жыл бұрын

Not all hero's wear capes. You are a Legend Harrison Armitage-Bath

@robertvondarth1730

2 жыл бұрын

Add %75 of the vid is 80’s porn music over showing lights reflecting in the paint

@willwarro4054

2 жыл бұрын

by then id have the entire car taped, papered, sanded, primed, sanded, tacked off. painted and let dry. then remove the tape. and still have time left to take a nap!

@meejmuas8686

2 жыл бұрын

Use extreme caution if using lacquer thinner. I accidentally got 2 smudges on my 2016 jaguar ftype ammonite grey paint and it dulled my car paint. It seeped past my clear coat and modified my paint. I have to now find a way to correct this by spray painting the smudges. They look worse than the repaired paint chips and are larger in size. Just skip the lacquer thinner completely and use something else if you dont want to deal with the risk

I can at least respect the owner of this Ferrari, as they obviously drove the car and didn't just buy it to have a garage queen.

@James2001

4 жыл бұрын

@Sleeping fuck off, stan. Ferrari owners don't need your dumb ass defending them.

@faizzaziz

4 жыл бұрын

Can see lots of battle scars on that F430. Ive lots on my Ghibli too and thats why I came to watch this video.

@Igaveyoumyfakename

4 жыл бұрын

Something tells me the owner doesn't need, want, or require your "respect "for what he or she does or doesn't do with their own vehicle.

@OldStreetDoc

4 жыл бұрын

Amen... I can’t imagine buying a car, $100 or $100K, and not driving it. Seems more than a bit douchey to have a true ‘performance car’ only to have it be a garage queen. Enzo would’ve been glad too ‘sell it’ to you, but he’d probably not respect you if you didn’t get it on the road.

@silentstormstudios

4 жыл бұрын

@@faizzaziz Why bother on the Ghibli? It's not worth anything anymore anyway!

You can focus your sanding by using a hole punch and crazy gluing it to a pencil eraser. This allows you to roll the pencil between your hands and avoid sanding off more of the clear coat than necessary.

Great video. Based on your tutorials, I did my 17' Range Rover Sport, in Cassin Grey. Prepped 30 spots or so, and a couple door dings, in about four hours. Prepped paint with 4/6 Sonax compound, isopropyl wipe down. Marked spots with small post-it stickers, so as not to contaminate spots with wax pen. Sanded with 2000 grit paper initially. but only in 1/2" circles. Cleaned chips with "farmers reducer", a bodyshop thinner on q-tips. Applied 4 coats OEM touch up paint, and 4-6 coats of OEM clear, with a 1mm artists brush($2). Following weekend, sanded with 2500 & 4000 grit, wet paper. Iso wipe, Sonax 4/6, compound again, and then did entire car with Chemical Guys V38 final compound, two coats Jet Seal, and four coats Zymol Carbon paste. All machine applied with a Festool rotax 125 RO, Griots orange pads on compound, red pads for polish, black pads for wax. Distilled water rinse and microfiber hand buff. All done, I spend about $300 on consumables and 20 hours over two weekends. You'd be hard pressed to find the chips now, and I'm over the moon about the results. I caught my boss touching my car in the office parking lot. said it felt like "wet", lol. Thanks so much for the videos. One of the only zero-hype, zero brand fan-boy channels on here, with solid techniques.

@CarCraftAutoDetailing

3 жыл бұрын

Wow, sounds like you really nailed it with you’re method and technique with great results to reflect that! Thanks for sharing your process and outcome, I really appreciate it!

@patrickthompson389

3 жыл бұрын

@@CarCraftAutoDetailing The NSX video was the inspiration for the effort, I'll try ceramic next year. Thanks for all your hard work on these vids, truly stellar.

@willwarro4054

2 жыл бұрын

just do like nascar and call a bunch of sponsors. they will pay you to put their decals right over those chips. if you go far enough they will completely body wrap it in whatever color you want. if it stands up to 200 mph, car parts thrown at it, then its gotta be the real deal. im gonna buy windshield tear offs. when it gets screwed up just grab the tab and rip it off and voila a new windshield.

@nicholasbabeaux2052

2 жыл бұрын

That’s awesome, I am about to attempt this on my brand new 2022 BMW in a gray metallic color, do you think that the same steps would apply to the plastic bumper? Or just metal? Thank you

@jeremyr7147

2 жыл бұрын

@@nicholasbabeaux2052 same steps

I work in paint for one of the big 3, we get chips like this straight out of a brand new paint job from the oven, we do a similar method, but use toothpicks, but..we have 30 seconds to do each touch up, all while on a moving line lol, it's tricky.

Yeah man, this is how you do it. And its explained in a manner so that even a novice can get the same results (given the right tools and PATIENCE) I would like to stress that to "APPLY NO PRESSURE against the surface while sanding" is of utmost importance let the sandingpaper do ALL the work. You did mention it, but it cannot be stressed enough to the inexperienced.

@BigStik2007

2 жыл бұрын

Could not have taken longer to get to the point. Porn music is cheesy and needless. But, thanks....

@SuperJman991

Жыл бұрын

@@BigStik2007 It really is some porn music isn't it.

Finally, someone showing how to correct rock chips THE RIGHT WAY.

@MrClempro48

3 жыл бұрын

You can also use little clear in the base

@suchgr8hieghts

3 жыл бұрын

@@MrClempro48 unless its metallic

@jakefromstatefarm9721

3 жыл бұрын

if you knew "THE RIGHT WAY" then why are you here?

@JonDough-ux9ju

4 ай бұрын

@@jakefromstatefarm9721because he paid someone 50$ in a parking lot to put paint in his rock chips and thought he was going to get body shop results. He doesn’t realize “THE RIGHT WAY” would be minimum 250$ -500$ depending on the amount of chips. I’m a painter but I use to do bumper welding and “touch ups” no one ever wanted to pay for it to be done right. They just wanted some paint in it. So I realized I could fix and sell a lot more rock chips at 100$ the wrong way then I can the right way. I can hide them for 100$ or make them disappear for 700$ guess what they choose.. every time.. 100$. Because if I’m going to sand and buff and polish. I may as well paint and have a PERMANENT fix.

The BEST rock-chip touch-up tutorial I've seen!! Good job!

@bones6978

3 жыл бұрын

I think you'd have more than a chip if a rock hit your car 😂

I will say it once, Sandro he's the Man!, If he cant do it, No one can. Go Sandro!!!!!!!!!!!!!!

Awesome job! I used to have a successful detailing business here in Japan, but could never do paint chip touch-ups like you've done here (could never get them flush). You're a real pro, and a great teacher.

@seanmoore4653

Жыл бұрын

how were you successful if you couldnt repair stone chips?

@jp1419

Жыл бұрын

@@seanmoore4653maybe he just details cars only

@jameskim2007

8 ай бұрын

@@seanmoore4653detailing business is not a car painting business buddy

I followed this step by step on a pepper white mini and You have saved me getting the whole bonnet painted!!

This video should be mandatory viewing for all car owners who care about their vehicle.

Best video ive seen for touch up paint, the theory makes sense and the results prove it. 8 haters are jealous and sad... thank you!!

hole punch the sandpaper and superglue the little circles to a new pencil eraser is how i sand these

@GOOSEAF

4 жыл бұрын

You know that is really a great idea. I have never heard of that nor thought of it myself either. Thank you

@lindenbasket

4 жыл бұрын

Yeah sweet little AMMO NYC tip

@2wheelcobra

4 жыл бұрын

not even gonna give AMMO NYC credit haha. Bitch move

@The_Kirk_Lazarus

4 жыл бұрын

Word of advice about the erasure-sanders: it is all to easy to be heavy handed.

@bobcalgarycanada8582

4 жыл бұрын

Great Idea Thanks

Great video Sandro. This is without a doubt, the best "touch up" work on rock chips I have ever seen done outside of a professional respray. Also the most outstanding results in the end by any professional detailer. Thanks for sharing your many years of experience with us enthusiasts out here in the world. I have to fix about six or eight rock chips on my red Nissan 370Z which also has very soft paint. After viewing this video it gave me a more in depth understanding of how to approach doing a more professional job on my chips. If my repair looks half as good as yours, I would be totally thrilled. Fortunately I have a Flex PXE-80 which hopefully will assist in achieving some great finishing results. I just have to pick up a few of those small 1" sanding disc's and a few of those finger sanding blocks in various grades. Thanks again for this great information and demonstration/tutorial! I've said it before and I will say it again, you are one of the BEST expert/master detailers on this entire planet! They should give you an Honorary PHD in Automotive Detailing! Dr. Sandro. The Doctor is in! 👍

It is so nice to see someone doing something the right way.

This is a whole new level of touch up. Most people don't have time or adequate garage for this.

This is best touch up work I have ever seen on my life!! I scratch my Prius and just ordered paint touch it up!!

As a dual tradesman i appreciate you taking the time to detail the correct procedure, while acknowledging that it may rarely be adhered to. Great presentation and camera work.

Quality finish,i wouldn't have thought it possible with sanding and a paintbrush, but there it is in front of my eyes,superb.

Great job. Excellent workmanship. At least 75 percent of car owners have chips in their paint. Thankyou

Taking the time to explain everything multiple ways was key for greater understanding. Great work

Fantastic video guide, i have done touch ups like this before but there's definitely a number of things i can take away from this for next time!

This is by far the best touch up paint correction i have seen

Just done my Honda Stream RS-Z in Cool Umber Metallic. I thought it was a so-so color at first, a few chips, less than the Ferrari and this is a daily Honda! Now after a good decontamination and clay bar and all chips filled, a good cut, polish and ceramic coating, wow! The metallic really sparkles under the light it has so much depth, color and shine it is astonishing it looks almost new. Really its a 10 year old car. Spent 2 full days when you add up the hours put in over a few days. Worth it; it looks better than the day I got it.

This is the 1st time I ever see paint touch-up whit amazing results, super job and video Thanks vm Sandro...…. Wes from NJ.

So glad you did this. You're literally the first detailer I've seen that showed how to do the retouch if you have a 2 step kit (my Benz kit has the clear in a different bottle) and even though I assumed if would be best to sand and compound, no one did that either. Thanks again Sandro.

@sylvainmarier4818

5 жыл бұрын

yeah I was looking to some pro detailer make some video to get some tricks, I have my car to do and it’s got a few stone ship Big thanks to you.

Excellent guide; most complete and better tips than I have seen elsewhere. LONG overdue fixing a whole starfield worth of chips on my old ride! You did a great job on that bonnet's paintwork as well.

finally a video with the right procedure .. thank you

Amazing video. Goes over every single step from start to finish. Thanks for taking the time to do this!

Just about to work on the touch up of my Volvo. Perfect timing for your video. Thanks. Most helpful.

At last, a pro solving the problem I have with the hood of my 2005 Mercedes SLK350. I don’t want to remove the factory paint but want to address the dozen or so chips. This is very helpful.

Buddy, by far this is the best video about stone chip repair. Trust me, I have watched tons of them. Yours is the best! Subscribed and Liked!!!

This is the best video on you tube for stone chip repair. Fantastic job.

It's worked great for me! This was not time consuming but actually time very well consumed for how it changed my 04 STI.

Was it the Ferrari that impressed me the most? The Flawless results of proper stone chip removal? The well presented video on doing something right? No! It's the gorgeously, meticulous and beautiful garage/workshop this guy maintains! Jealous, Hell ya!

I had a chip on my car that needed repair. Most videos show people dabbing the chip with a brush or a paint stick and that’s it. Though the chip is filled, the repair looks awful. I followed your steps on my car and I have to say the chip is gone. I was lucky my paint touch up matched, but without your steps it would never look as good. The trick is go slo and take your time. Great video. Thanks again!!!!

FINALLY an informative video that clearly shows how it's done! I've seen a bunch of videos that are real garbage compared to this, thanks!

Incredible job! Thank you for sharing your expertise. There's so much myths repeated all over youtube about other 'miraculous' ways of doing this...

Bloody brilliant andreas. Perfect example of what we discussed in the TCB podcast. Bravo for calling them out 😁

Fantastic Learning Tool. I have been using all the wrong methods to wash my cars over the years. This video has helped me change the way to wash a car with outstanding results. Cheers

Clearly a very thorough and detailed method to fix stone chips.

This is done properly ...... A refreshing change , most detailing on youtube is dogshit. This guys knows his stuff, when I worked in a bodyshop, this was the ONLY way other than repainting the whole panel.

@ewlinitis

5 жыл бұрын

Pan is a great detailer.

@billl8530

4 жыл бұрын

There are many great detailing channels on KZread etc us thus guy talking about.

@james-jq8sk

4 жыл бұрын

Are you his brother 😂

@rhino015

4 жыл бұрын

Labour is really expensive where I live. Do you reckon if that’s the case then painting the whole panel might work out cheaper or the same price? If it’s the same price you’d prefer that I guess

Sandro, I wanted to send a thank you for all the work you put into your videos. As you well know there’s an infinite amount of information/ videos out there but yours are the absolute best. Stay passionate!

Thank you for putting this up. I watched dozens of videos and this is by far the best.

Using the three foot rule it looks perfect, on closer you can detect the spots but only you know that hood so well. Great tips, thanks for sharing.

You walk A guy in there and if he can call out where you touched up. I would be blown away, that looked perfectly excited and l couldn't see anything even zooming way in so I'm going to call that shit PERFECT!

This is the reason I watch your videos. We might not be able to do what you do but we can get close because we now know the right way to do “X”. As always I learn something every time I watch your videos.👍😁

By far the best video Ive seen and it gives me more confidence that its from an actual pro on a pretty expensive car.

Wife walked in. Wife asked if I'm watching 70's porn. Nice background music.

@jacquesduplessis6310

5 жыл бұрын

@Pedro especially 70's porn 🤣🤣

@frankobrien9124

5 жыл бұрын

& was you ?.

@unclemarksdiyauto

5 жыл бұрын

Yep, hope she believed you were watching a car refinishing video!

@miguelarvizu9681

5 жыл бұрын

Hahaha my wife said the same thing. Great video and very informative.

@wyaldkingdom

5 жыл бұрын

Some see a problem I see opportunity. I would have said "can you help polish me off?" If she gets mad then you say "it's just a car video." If she smiles then thank me later for my advice. Lol

At the beginning, I was like: bloody hell, he f*kd up the paint!!! But then after the polishing...boy I was amazed! Good job sir!

@Alex-us2vw

5 жыл бұрын

Wet sanding is commonly done to brand new cars paint by owners who can’t stand the factory orange peel. It’s also done by bodyshops when getting a high end paint job to get an immaculate finish. Without wetsanding a touch up job would look hideous.

God I wish you had done this video several months ago as it would have saved me $$$$$ repainting a bonnet and roof. Really good to know how to do this repair now the best way possible. Well done again.

This will help make my rusty old lawn mower look brand new! Thanks for the tips ❤️❤️

Great video: You explain just how complicated this really is. So many steps. Some of us are lucky that we don't drive old Ferrari's....I have a 2012 Infiniti G37xS Coupe in Red and I was able to purchase a touch up pen with real paint and not the water based crap that they sell at the stealership. The paint pen has regular paint on one end and clear at the other and are felt marker style. The front portion of my hood and some parts of the car including the mirrors are covered with the 3M clear cover. So my chips are on the rubber/plastic bumper. I use a fine paint brush too...after I've thoroughly cleaned the car I make note of the chips. I shake the pen to make sure that the paint is consistent in thickness. Then I dab a bit of paint on a small plastic plate and then soak the paint brush in the paint and apply a small amount of the paint in to the chip. I wait for it to dry as these types of touch up paint pens dry faster than body shop paint. Then I apply a small amount of clear coat. If you apply just the proper amount of both paint and clear the paint will fill the crack and just a bit of mild quick detailer hand polish with a microfibre a day later after the paint has cured and hardened will blend everything in. I use Meguiars Ultimate Quick Detailer with a quality microfibre cloth in a vertical followed by a horizontal motion to prevent any kind of swirl mark. I'm my case I'm too chicken to sand anything. But I can tell you that after a week later if I still see any uneven paint from the touch up job, I can do a machine polish and the results are amazing too. Sometimes after I wash the car I use a q-tip dabbed in alcohol to clean the chip. While I have your attention I also recommend using the 3M clear cover on your headlight lenses to prevent oxidation and pitting and a proper car cover if you like to leave your car outside in the summer. (Actually 3M clear plastic is a rubberized version of clear coat!) I can't stress enough how this actually saves you so much trouble. Thanks for a great video! Cheers from Montreal, Canada!

You confirmed what I was thinking about this technique. I just bought a used car and did redo all the “corrections” from the garage by myself. They applied touch pen as peanut butter while I followed your technique. It’s not that time consuming for me, even if I can understand this process costs money for the garage. But they are supposed to be pro... Anyway I did not pay for that previous job so I tried your steps carefully and I could get a wonderful job on a black sapphire paint. It is neat, I’m impressed myself! Big thanks! 🙏

@KCMrecordings

2 жыл бұрын

How did you undo their bad touch up job?

@knakikrakot

2 жыл бұрын

@@KCMrecordings I did my best as explained in this video ;)

@meejmuas8686

2 жыл бұрын

@@KCMrecordings probably sanded down the previous work

Thank you very much for this most interesting and informative video; you've saved me a couple of thousand dollars over what a paint and body shop wanted to charge me to repair a few small stone chips on my new 370Z.

Perfectly painted. Well done man. I never saw a video with pait correction like this. Very appreciated and i can learn how to do it

Nice video - I think I'd be freaking out at the sanding stage thinking to myself what have I done to my car! Great end result!

@alanhodgson9421

2 жыл бұрын

Picking up the sandpaper the first time was ... hard.

Very meticulous eye for detail. Exceptional job. Thankyou for some great advice. Ash.

Best tutorial of paint touch I have seen. Great work, keep it up Sandro. Nice car to work on too. Will bee using this method for chips from now on.

That's how you do it, - proper job! Brilliant video, thank you so much for posting. I'm going to tackle my own stone chipped bonnet with much more confidence now!

Very good video, I found it very useful, thanks for taking the time to post 👍

Use a toothpick to apply the paint. This keeps you from applying too much at once to have thin layers. This will also eliminate brush stroke marks and helps the paint from drying darker than the original color.

@carbonoxx

Жыл бұрын

if u want pro touch up, we use airbrush

I just chipped the paint on my Ferrari 355. I'm sick about it but this gives me hope. Great Job!!

Thanks, I do it every day on ' Cheaper' cars but very good video .Just like to point out that Good paint and Patience are vital to get a good job.!

I learned a lot. Thank You.

I am in the same situation..only difference ..I have an 04 Mini Cooper S, chili red..I am doing all the door knicks..very informative video..thanks

Great vid mate! Been something on my mind as I have a few on some of my cars I want to address. Can't wait for full length vid - Keep it up! #1

Hell yeah! I needed this video too 😂 I have little circular places on the hood that don’t have paint 🤷‍♀️ I didn’t even know there was a 4000 grit sandpaper 😳 I can’t thank you enough for teaching me how to fix my old paint job!!! New subscriber 🤙🏼

Brave man sanding on a Ferrari. Great tips. No wonder mine looked like crap.

@peterwillems2422

4 жыл бұрын

I don't think any Ferrari would look like crap 😜

Wonderful video, great showing of what a meticulous process it is to touch paint the right way. Quality takes time, so many on the internet show all these quick hacks for doing stuff like this and it looks good on camera, but the reality is those quick results are so inferior. Well done

Nice one. Got a few chips on new Volvo V90 and ws looking on best way to do this. Really helpful and kept it simple enough for the average car owner.

Terrific tutorial. Very professional production, script & voice over. It was straightforward and easy to follow. Thank you!

Your attention to detail is inspiring

I'm afraid I might rub through the clear coat, but I'm going to give it a try anyway on a spot least conspicuous. If all goes well, I'll tackle the remaining chips. Thanks for the expert tips.

@nighthawkj30A4

5 жыл бұрын

Michael Butler i would imagine using 3000 or 4000 grit paper soaking in water shouldn’t rub though the clear. But i guess its possible. I would use the 4000 and sand only enough to fix the damaged area. But he makes seem so easy.

A couple of years later and this is still the best Video I have seen. Great detail, thanks!

Wow. This is some one of the best channels I've found on the topic. Thanks!

Well done Sandro...Every time I hit the thumb up button before watching the vid and I am sure to do that.Eagerly waiting for upcoming vidz.

Really good tutorial, thanks. I have several chips I'd like to tackle on a classic without a respray and I think the tips I take from this has given me the feeling I can improve my chips enough, great job, thanks again for posting this.

@GOOSEAF

4 жыл бұрын

If you don't mind, may I add a comment from experience? I'm assuming you said yes ... double check your touch up paint color somewhere inconspicuous and make sure that they are absolutely identical to your car's color otherwise they'll Stand Out worse than the chips did. Even if the tint is a little off. I had that happen once on a black car, and boy did they stand out. If you hadn't already thought of it or somebody already told you then hopefully that is useful. Best of luck with it.

Wow, best video i have found on this! The job was fantastic! Glad the car is driven too...

Amazing content Sandro! Cheers from Florida, keep it up man you’re the best!

Awesome steps. I wish other garages learn from you

Bravo! Well done Sir. Well done indeed. Truly enjoyed watching this video.

Some really helpful tips here that will get me much better finishes on my next touch up jobs, thanks for this!

Thanks ! That's a great video. I will be trying this on my 1985 Ferrari Mondial QV in Argento Metalica.

I learn more and more everyday from your channel. I'm not on this level yet, but I'm far better than other detailers around me because of the genuine knowledge you provide. I wish there was a way you could critique my work so I know what NOT to do the next time.

The biggest mistake I see, and it's very hard to avoid, is making a slight low spot in the clear around the chip. The darker the color, the more obvious the dip. To avoid this, I use an old painters trick. After you build up the chip area with clear and it cures, apply body filler to the area using the built up clear as your highest spot and tapering out to your sanding limit. Block down the filler and built up clear until you are just back down to the base clear. This will prevent you from creating a small wave in the clear.

This will be my first time doing a touch up job to my car, and you simply made it look so easy; Eloquently put, you have dumb this down to the level where I feel extremely confident with my touchup job that I will be performing with your step-by-step including the wet sanding and polishing steps to the tee. Great job and thank you very much for your post

@Gimpbold

Жыл бұрын

Hey m8. How did it go?:D

@marcrajabi71

Жыл бұрын

I was wondering the same

I watched this video when it first went up and now, I finally get to try my hand at it on my new car I got this August (2022). Small chip that made it to the primer. Should be fun! Paint will be from a paint pen but I will be adapting the technique from this video into the work. Paint is obviously super new so the car doesn't need a lot of prep but prep at the area of the chip will be properly thorough.

At last ... a comprehensive well explained video.. big thanks

This is so above my ability but I watched through to the end just because the colour is gorgeous as is the car! Brilliant music too, great stereo width. Cheers cobber!

Time to fix some chips in my Tesla Model 3. Did it several times before in this technic Sandro, so know how to and what to, but have returned to your video again ))) Thanks Man!

Your videos are really informative. I have been waiting for your next video. Thank you and l am very much looking forward to the full length video on this F430. Thank you for taking the time to do this video

I was like what is he doing.... Then I was like, wow, nice work.

Good Job Sandro! But honestly from a spray painters view when i saw the amout of paint chips from 2.10 to 2.15 in the video i said that needs paint especialy on a F430.

Thanks for uploading this video. I have some paint chipped on a doors edge from a scrape and am looking to attempt at touching it up. The before and afters on this Ferrari is amazing.

Great job, and an even better tutorial. Really appreciate it as I have a LOT of rock chips to repair on my new to me F150 I just bought. 💪 Thank you.