Hey, looking to upgrade my basic streaming set up from a single stationary camera to your PTZ MOVE SE 30X. This video helped a ton as I knew very little about how to connect cameras to a controller and such. That all makes sense now. But how do I get the video from the network switcher via ethernet cable to my laptop? I run a mobile streaming set up and run just off wifi as most of the places I stream from don't have access to a hard-wired router. Will the video signal be sent from the switcher to my laptop via another ethernet cable? I didn't realize ethernet cables could transmit video as well. (As I mentioned, very much a rookie in this field ha-ha).

@PTZOptics

4 ай бұрын

Hello! Upgrading your setup to include a PTZOptics PTZ MOVE SE 30X camera is a great choice for enhancing your streaming quality and flexibility. To address your question on getting the video from the network switch to your laptop, especially in a mobile setup using WiFi, let's clarify a few points about the workflow and the necessary equipment. 1. Ethernet for Video Transmission The PTZ MOVE SE 30X, like other PTZOptics cameras, supports video transmission over Ethernet using the NDI® protocol or standard network streaming protocols (such as RTSP or RTMP). This capability allows you to use a single Ethernet cable to both control the camera and receive its video feed, provided your network infrastructure supports it. 2. Connecting to Your Laptop To receive the video on your laptop from the camera over a network switch, you'll need to ensure your laptop is connected to the same network. Here's how you can do it in a mobile setup where you're relying on WiFi: Connect the PTZ Camera to the Network Switch: Use an Ethernet cable to connect your PTZ MOVE SE 30X camera to a network switch. This switch should be capable of handling the bandwidth required for video streaming. 3. Connect the Network Switch to Your Laptop: If your laptop has an Ethernet port, you can directly connect it to the network switch using another Ethernet cable. This setup will ensure a stable connection for both controlling the camera and receiving its video feed. If you rely solely on WiFi and cannot or prefer not to use a wired connection for your laptop, you'll need a WiFi router connected to your network switch. This router will broadcast the network over WiFi, which your laptop can connect to wirelessly. Ensure the WiFi router is configured correctly to allow devices on the WiFi network to communicate with devices on the wired network (like your PTZ camera). 4. Software for Video Reception To actually view or stream the video feed from your PTZ MOVE SE 30X on your laptop, you'll need software that supports the camera's streaming protocol (NDI®, RTSP, RTMP, etc.). OBS Studio is a popular choice for this purpose, as it's free, supports various streaming protocols, and works well for live streaming setups. Within OBS or your chosen software, you'll configure a new source using the camera's network stream URL. 5. Mobile Streaming Considerations Bandwidth and Quality: Streaming video over a network, especially HD or 4K, requires a significant amount of bandwidth. Ensure your WiFi network is robust enough to handle the video stream without significant loss in quality. Latency: A wired connection is generally preferred for the lowest latency. If using WiFi, be aware that there might be a slight increase in latency. Power Supply: Since you're running a mobile setup, ensure you have a reliable power solution for your camera, network switch, and WiFi router. By following this setup, you can efficiently integrate a PTZ MOVE SE 30X camera into your mobile streaming setup, leveraging the flexibility of PTZ cameras and the convenience of wireless connectivity for dynamic and high-quality live broadcasts. Thanks for checking out our Channel! Learn More: ptzoptics.com/

@PowerHippoStreams

4 ай бұрын

@@PTZOptics forgive my lack of knowledge here, but is there a simpler way to run it? Just hdmi into my laptop or is the whole IP connections and such mandatory?

@PTZOptics

3 ай бұрын

Hello, apologies for the late reply. For connecting a PTZOptics MOVE SE 30X camera to your laptop, using HDMI is indeed one of the simpler ways to get the video feed into your system, especially if you're looking to avoid the complexities of IP networking. The HDMI connection provides a straightforward method for video capture but keep in mind that it will only carry the video signal. Here's a basic overview of how you might set this up: 1. HDMI Connection: Connect the PTZOptics MOVE SE 30X camera to your laptop using an HDMI cable. Since most laptops do not have an HDMI input, you will likely need an HDMI to USB capture device. This device acts as a bridge, capturing the HDMI video signal and converting it into a USB input that your laptop can recognize. 2. Capture Device Setup: Plug the HDMI to USB capture device into your laptop. You may need to install drivers or software for the capture device, depending on the model and manufacturer. 3. Camera Control: While HDMI will transmit the video signal to your laptop, controlling the PTZ (Pan, Tilt, Zoom) functions of the camera via HDMI is not possible. For camera control (panning, tilting, zooming), you would still need to use either an IR remote that comes with the camera, an RS-232/RS-485 controller, or network-based control (if you choose to explore IP control in the future). 4. Software Configuration: Open your video capture or streaming software (e.g., OBS, vMix, etc.) on your laptop. Configure the software to recognize the USB capture device as a video source. From there, you can manage your livestream or recording settings as desired. 5. Using an HDMI connection simplifies the video capture process by bypassing network setup procedures, making it a good option for users looking for a plug-and-play solution. However, for more advanced features like remote camera control or accessing the camera's web interface for detailed settings adjustments, network connectivity would still be necessary. This method is well-suited for users who prioritize ease of setup and are primarily focused on capturing high-quality video without the need for remote control over the network. Please reach out to our PTZOptics Support Team Support Numbers: 833-888-9706 or 484 593 2584 Monday -Thursday: 8am to 6pm EST Friday: 8am to 4pm EST Not open Saturday or Sunday. Community Portal: community.ptzoptics.com/s/ Thanks for checking out our Channel! Learn More: ptzoptics.com/

We need a video on recommended network switches for connecting multiple cameras and devices using NDI that help reduce lag

@PTZOptics

5 ай бұрын

Hello! Creating a network setup that effectively supports multiple cameras and devices using NDI (Network Device Interface) requires a robust and capable network switch. NDI is a high-bandwidth protocol that allows for low-latency transmission of high-quality video and audio over a network. When choosing a network switch for an NDI-based production environment, several key features are important: 1. Gigabit Ethernet Ports: Each port should support at least 1 Gbps, though 10 Gbps is preferable for larger setups or 4K workflows. 2. High Bandwidth and Throughput: The switch should be able to handle the aggregate bandwidth of all connected devices without bottlenecks. 3. Quality of Service (QoS) Capabilities: This allows prioritization of NDI traffic over the network, ensuring smooth video streaming. 4. Managed Switch Features: The ability to configure and manage the switch is crucial for optimizing performance and troubleshooting. 5. IGMP Snooping: This feature helps in managing the multicast traffic which is common in NDI workflows, reducing unnecessary network load. 6. Low Latency: Look for switches that offer low-latency performance to ensure real-time video transmission. 7. Reliability: Enterprise-grade or professional-grade switches are recommended for their robustness and reliability. Recommended Network Switches: 1. Netgear ProSAFE Series Models like the GS108T, GS110TP, or GS728TP are popular in smaller setups. For larger installations, consider the M4300 or M4500 series. 2. Cisco SG Series Cisco SG300 or SG500 series switches offer robust performance and are suitable for mid-sized to large setups. 3. Ubiquiti UniFi Series UniFi switches like the US-16-XG or US-48-500W are well-suited for NDI, offering a good balance of performance and manageability. 4. TP-Link T1600G / T2600G Series These switches provide good performance with QoS and IGMP snooping, suitable for small to medium-sized setups. 5. Aruba Networks Switches Aruba offers several switches like the 2530 and 2540 series that are reliable for professional environments. 6. D-Link DGS Series The DGS-1100 and DGS-1210 series are cost-effective options for smaller NDI setups. 7. Extreme Networks X440-G2 For larger and more demanding environments, this switch provides high performance and extensive features. Additional Considerations: - Power Over Ethernet (PoE): If your cameras or other devices support PoE, consider a switch that provides PoE capabilities to simplify cabling. - Future-Proofing: Consider the future growth of your network. Choosing a switch with more ports and higher capacity than currently needed can be a wise investment. Remember, the best switch for your setup will depend on the specific requirements of your NDI workflow, including the number of devices, video resolutions, and overall network infrastructure. Always verify the compatibility of the switch with your specific NDI devices and software.

Hello my brother ! I have the FeelWorld USB 10 camera, with the controller I can't connect the ip, When I set the IP it says connect error Visca! Please help me

@PTZOptics

4 ай бұрын

Hello! Connecting multiple PTZ cameras to a controller, especially when using a specific model like the FeelWorld USB 10 camera controller, requires a bit of setup to ensure seamless operation. The "connect error Visca" message you're encountering typically indicates an issue with the VISCA over IP communication between your controller and the PTZOptics cameras. Here's a step-by-step guide to troubleshoot and potentially solve this issue: Check Camera IP Configuration: Ensure that each PTZOptics camera has been assigned a unique IP address that is reachable within your network. This can usually be done through the camera's onboard menu or a web interface if the camera is already connected to your network. Update Firmware: Make sure that both your PTZOptics cameras and the FeelWorld controller are running the latest firmware. Firmware updates often resolve compatibility issues and improve overall functionality. Verify Network Settings: Ensure that the cameras and the controller are on the same subnet. For example, if your controller has an IP address of 192.168.1.5, your cameras should have IP addresses like 192.168.1.6, 192.168.1.7, etc. Check the network switch and router settings to ensure that they are not blocking VISCA over IP commands. Some network equipment may require specific configurations to allow for multicast or unicast traffic, which is often used by PTZ camera control protocols. Controller Configuration: Within the FeelWorld controller, carefully re-enter the IP addresses for each camera, ensuring there are no typographical errors. Verify that the VISCA over IP settings (such as port numbers) on the controller match those expected by the PTZOptics cameras. PTZOptics cameras typically use port 5678 for VISCA over IP control. Test Connection: Try to control each camera individually from the FeelWorld controller to isolate any specific configuration issues. If available, use a network scanning tool or software to confirm that the controller is successfully sending commands to the cameras’ IP addresses. Consult Documentation: Refer to both the PTZOptics and FeelWorld controller's manuals for specific instructions on VISCA over IP settings. These documents often contain crucial details for troubleshooting network communication issues. Contact Support: If after following these steps, you're still experiencing issues, consider reaching out to PTZOptics support or the support team for your FeelWorld controller. They may offer additional insights specific to your setup and equipment. By carefully checking each of these areas, you should be able to resolve the "connect error Visca" message and successfully control your PTZOptics cameras with the FeelWorld USB 10 camera controller. Thanks for checking out our Channel! Learn More: ptzoptics.com/

You said on the serial you set the second camera to cam 2 but how?

@StreamGeeks

3 ай бұрын

It’s set in the OSD menu and the joystick

@PTZOptics

3 ай бұрын

Hi Jason, To set the second PTZOptics camera as "Cam 2" on your joystick, you typically need to adjust settings both in the camera's On-Screen Display (OSD) menu and on the joystick itself. The process involves setting the camera's address to 2 (or whichever address corresponds to "Cam 2" on your joystick) and then configuring the joystick to recognize and control this camera as "Cam 2." Here's a general guide to help you through the process: Step 1: Setting the Camera's Address via the OSD Menu Access the OSD Menu: Connect your camera to a monitor or TV, and use the IR remote control or joystick to access the OSD menu. This is usually done by pressing the "Menu" button. Navigate to the Communication Settings: Use the arrow keys on the remote control or joystick to navigate to the communication settings. The exact naming might vary, but you’re looking for options like “Communication,” “Network,” or “Serial Communication.” Change the Camera Address: In the communication settings, look for an option labeled something like "Address," "Camera ID," or "Device ID." Change this setting to "2" or the desired number corresponding to "Cam 2" on your joystick. Save and Exit: Make sure to save your changes before exiting the OSD menu. Step 2: Configuring the Joystick Controller Power on the Joystick Controller: Ensure your joystick controller is powered on and connected properly to all cameras and any control interfaces. Assign the Camera to a Button: Depending on your joystick model, you may need to assign the camera you just set to "Cam 2" to a specific button or preset on the joystick. Refer to your joystick's manual for specific instructions on assigning camera addresses to buttons or presets. Test the Configuration: After setting the camera's address in the OSD and configuring the joystick, test the setup by selecting "Cam 2" on the joystick and using the controls to pan, tilt, zoom, etc. Ensure the commands are controlling the correct camera. Important Notes: The exact menu names and steps can vary depending on your PTZOptics camera model and the firmware version. Always refer to your camera's manual for specific instructions related to the OSD menu navigation. Similarly, joystick controllers can vary in terms of configuration options and procedures. Consult the manual for your specific joystick model for detailed instructions. By setting the camera address through the OSD menu and then configuring your joystick controller accordingly, you should be able to control your second PTZOptics camera as "Cam 2" from the joystick. If you encounter any issues during this process, consulting the specific manuals for your camera and joystick model or reaching out for support might be helpful. Please reach out to our PTZOptics Support Team Support Numbers: 833-888-9706 or 484 593 2584 Monday -Thursday: 8am to 6pm EST Friday: 8am to 4pm EST Not open Saturday or Sunday. Community Portal: community.ptzoptics.com/s/ Thanks for checking out our Channel! Learn More: ptzoptics.com/