Bro I already do that..and it broke my tp4056 module...you're very good at editing...have a goodlife

@lovelycollection100

Жыл бұрын

Yes me tocó, broke my module.

Thanks... Good job....

More details. Thanks. Keep it up

R3 resistors remo pannitu எண்ண velvu resistor podalam sollunga....

Thank you ❤️❤️

Nice explanation bro

Can I do series power output of this circuit which you have made Please reply me sir 🙏🙏🙏 Nice video one of the best❤

@letsclear9769

Жыл бұрын

Ya bro you can take series output but you need to charge the module with 3 seperate charging source ie) 3 chargers connected seperately but the current output is low I recommend to go with bms

Bro nega output connect pana mathiri power connection +,- join pani total la 12 v charger use panalama bro

Felicitaciones. Muy bueno

Anna oru module oru 3.7v battery 🔋 than charge panna mudiyuma? illati 2 battery 3 battery a oru module le charge panna mudiyuma?

Dai vicky super da

Thank you bro, you design an awesome solution with charging balance (or isolation?) and make it possible to series 3s 18650 battery which could output 12v. One question: Is the output circuit (12v) being protected by TP4056 module? Is there any chance that make battery over-discharging? I'm worried about the safety and don't want burn anything lol. Hope you can give me any reply or suggestion, thank you a lot !

@letsclear9769

3 жыл бұрын

This board has ever protection features like over current discharge protection max 2A Over charge protection max 4.2v Over discharge protection min 2.5v Shot circuit protection So don't worry about it

@steavekamei2013

2 жыл бұрын

don't try this method it's not safety

@charesealbow5357

Жыл бұрын

@@steavekamei2013 why was it unsafe?

Data sheet diagram how to connect it you have told some 1st pin to 2 sheet to collect na pls explain me

👌

I make same with mobile battries when i try to charg it this module with 12v 1Am but its not charged after 12 hours😬

Parabéns

awsome kindly post more videos... i have a problem bro.. 555 motor fan ready panunaen.. 3 litium battery use pani 12 volt supply... but battery over discharge agi waste agiruchu...how to protect over discharge ..kindly reply me or .video podunga..

@letsclear9769

3 жыл бұрын

Bro athuku bms (battery management system) vaikanum ethuku na video ready panni vachi erukan don't worry voice motum tha kudukanum na sekrom post panran

@satishrajp1934

3 жыл бұрын

@@letsclear9769 boost converter use panuna battery overdischarge portection kaedaikuma

@letsclear9769

3 жыл бұрын

Ella bro booster converter use panna battery output voltage tha increase panlam but protection panathu li ion battery ya 2.5 volt kela discharge panna waste ha poidum

@letsclear9769

3 жыл бұрын

Nane toy car ku bms board vaikama li ion battery 3 use panni 12v power ku ready panni thambi kita kudutha konjom neram otitu vaika sonnen ana avan romba neram ottitu 0 volt vara discharge pannitan so 3 battery um close charge avala waste ha pochi

@satishrajp1934

3 жыл бұрын

@@letsclear9769 same bro...best solution kudunga...waiting for the video..

Clear instructions. Nice!

can you short the i/p 5v off all 3 boards if so how much current will it consume for full discharged batteries, can this be used as a replacement for 10A 3S bms

@letsclear9769

2 жыл бұрын

In Fully discharged condition each module charge their batteries with 1amp so total of 3 batteries it consumes 3amp so we should give 5volt atleast 3amp dc input to the module No it doesn't replace 10A 3s bms It is limited for 3 amp maximum

Bro supper nengethan poriyuramathiri sonninge

@letsclear9769

2 жыл бұрын

Thank you bro💛

Athu mattum illame 3.7v battery a thavira vera enna enna voltage battery a inthe module le charge panna mudiyum

English subtitles are not available

Let's clear bro

Can I charge only 1 battery of your circuit which you made ????

@letsclear9769

Жыл бұрын

Yes of course u can charge a single cell with this circuit because every single module is seperately connected with its respective cell holder

@manjusripratihar6350

Жыл бұрын

@@letsclear9769 thanks 🙏🙏🙏🙏

Bhayya good morning. Can I connect a boost converter to TP4056 while it is charging a battery? Please reply

@letsclear9769

3 жыл бұрын

Where you going to connect booster converter wheather to input or output of tp4056?

@rehanshayaan6872

3 жыл бұрын

@@letsclear9769 To the output bro. I want to feed 12v to a load connected via boost converter, I want to know whether charging at the same time when the load is connected destroys the circuitry.

@letsclear9769

3 жыл бұрын

It will not damage the Circuit if you connect the charging battery (li-ion one cell per board) and booster converter in parallel connection Tell me what and how many battery you going to change? 👍It is ok to connect booster converter to output but the maximum ampere of tp4056 can deliver is 1A when the load and charging take more than 1A then the circuit cut off the current or the ic get heat if not cutoff done. So measure the current flow from tp4056 to ( load and charging ) If it comes under 1Amp then it is ok but 1A continue discharge will heat up the ic so you should fix a HEAT SINK (compulsory) on that ic What project you going to make Tell me I will help you 😊

Bro board output la 4007diode use paninanum bro Ilana ion battery sati aiedum

@letsclear9769

3 жыл бұрын

Why bro diode use pannanum ? I think here no need of diode

@jeyajeya9843

2 жыл бұрын

Mk tech unga number thanga bro pls

Bro charging input loop seyth kodukka mudiyuma.onnilirunth rand.randilirunth moonn appadi.mudiyumna ore chargerale charge panna mudiyuma

@letsclear9769

2 жыл бұрын

Hmm panlam oru charger output ha parallel la 3nu board kum connect pannanum

@letsclear9769

2 жыл бұрын

But antha charger 5v 3amp mela support pannanum 5volt 1or2amp charge use panna charge aavom but later aavom full charge ava

great stuff but still its max amps is just 2amps

@letsclear9769

3 жыл бұрын

Yep, it can use for low power stuff(below 2amp) like emergency light. it will last long because of it 3 cell in parallel add on mah

2A charger use panni charge pannalama...appadi pannum pothu board overheat issue iruku ...bro pls rply@lets clear

@letsclear9769

2 жыл бұрын

Bro general la board heat avatha seium bro antha heat naba kaiyala tolerate panra mare erukum appadi ella over heat avuthuna board tha problem or heatsink use pannunga

I have 3.6v , 4.8amp flash light li-ion battery,which module could use

@a1a2o22

2 жыл бұрын

tp4056 or tp5100 2A

Is it possible to charge 12v battery(w/ BMS)?

@letsclear9769

3 жыл бұрын

It only change 18650 Li ion cells

Hi bro pls till how to connect in bord you have told that

@letsclear9769

3 жыл бұрын

Bro I can't get you contact me in instagram

@letsclear9769

3 жыл бұрын

Bro I can't get you contact me in instagram Id bsvigneshack2001

12V will burn the TP4056 finally .

oru common power supply ah series ah vechu charge panlama

@deepanraj2245

Жыл бұрын

Athe mari intha board ah vechu 3 cell lithium polymer ku use panlama

@letsclear9769

Жыл бұрын

Bro ithu na summa experiment pannipathan bro 3sbms porathuthan best hu

@letsclear9769

Жыл бұрын

Pannalam bro ana seperate charging source venum

@deepanraj2245

Жыл бұрын

@@letsclear9769 thanks bro

Can I charge it using normal mobile charger?

@letsclear9769

2 жыл бұрын

Yes

Is this safe ?? And can I use 6 batteries ( 2 batteries in each circuit)??

@letsclear9769

3 жыл бұрын

Yes, you can use 2 or even more battery for each circuit but in [PARALLEL CONNECTION] And you should keep it in mind that Time taken to full charge get more and more by adding of battery Because the circuit board is charger the battery with maximum (1A) when using one battery it changes at 1A While using 2 batteries it changes at 0.5A for each battery (current get divided by no. of battery used) so double the time of charging when using one battery the board charge at 1A(at 0% battery charger) and gradually decreases to 0A(at 100% battery charge) But using 2 batteries in parallel the time taken to full charge get double so high charging current (1A) also not decrease faster it takes double the time to decrease so the ic get very hot so you should fix a [HEAT SINK] to top of the tp4056 ic.

@senterterapibioglass3677

3 жыл бұрын

This module is not recommended for more than 1 battery. You must use charging module like BMS.

@letsclear9769

3 жыл бұрын

Yes your correct , but I tried with even three batteries in parallel connection it workes fine and charge the battery fully but takes more time and the board ger heated up in initial charging after using heat sink heating is reduced

@senterterapibioglass3677

3 жыл бұрын

@@letsclear9769 the board in normal condition with original R3 and 1 battery, will be very hot even with alumunium heat sink 14x14x5mm because the current taken from the charger around 1000mA. Using mini fan + heat sink is the best way to reduce the heat.

What the name of music?

@letsclear9769

3 жыл бұрын

Tobu candyland Link:kzread.info/dash/bejne/e32mpaZ6hparl6w.html

Whare are you from bro

@letsclear9769

3 жыл бұрын

Melmaruvathur

Oru board la yethana battery charge pannalam

@letsclear9769

9 ай бұрын

Evlo battery vena parallel la charge pannalam bro but time delay aagum

Audio is muffled

Bro idhu safeah irukkuma

@letsclear9769

Жыл бұрын

Bro negaa 3s bms vangeyee use pannikongaa cheap haa kadaikuthu 3s bms lam

Battery price bro

@letsclear9769

3 жыл бұрын

I got this for ₹100 per battery

8:41 single charger use pana mudiyatha bro

@vigneshb.s4541

3 жыл бұрын

Ella bro short circuit avom

@vigneshb.s4541

3 жыл бұрын

So kandipa 3 charges use pannanum

@satishrajp1934

3 жыл бұрын

@@vigneshb.s4541 but thani thaniya charge panikalam...

@vigneshb.s4541

3 жыл бұрын

@@satishrajp1934 hm panlam but time avom

Ake mobail charger sa kase charge kare?

@letsclear9769

3 жыл бұрын

English please

@meerabai9269

3 жыл бұрын

@@letsclear9769 how to charge in one mobail charger

@letsclear9769

3 жыл бұрын

Take a single charge of 5v and 3A above and connect it in parallel connection to all the module

@meerabai9269

3 жыл бұрын

@@letsclear9769 thanks 2amp ha

@letsclear9769

3 жыл бұрын

Use a 20watt oppo f15 charger it can support upto 4A but not a 2A because the charge get heat up

English, subtitle not avaiable

@letsclear9769

2 жыл бұрын

Sorry for that bro if you have any doubt please leave comment to the respective videos

Saund kam kano

@letsclear9769

2 жыл бұрын

English please

Not balance charging.... Not recommended at all

@letsclear9769

2 жыл бұрын

Ya your correct m but before the circuit is connected to charging all battery are connected in parallel and equalised the voltage and every module manage their respective cell so don't worry

Can't work. With how many volts will you charge it? This is the biggest joke of the year.

@letsclear9769

9 ай бұрын

It working dude , It need to be charged in 5 volt with seperate power supply (chargers)

👌

@letsclear9769

3 жыл бұрын

Thank u Anna