This method is a stroke of genius! Works 100%. I was initially struggling a lot and was afraid the tire levers will damage my carbon wheels. With this method I did not even have to use the tire levers or struggle with the tire at all. Thanks a lot for this video @Durianrider

400 watts, EASY, 120 cadance EASY, norton summit under 12 minutes, easy, change a tyre, just easy!

I swear I was gonna make one of these videos next week

@TDeansbeans

3 жыл бұрын

Do it anyway but with a brand new tire on a tight rim. Not a used tire that’s been stretched a bit

@philjono2462

3 жыл бұрын

Get a gp5000 on a Mavic rim, with 2 normal tyre lever and I’ll give you £100

@JTChi

3 жыл бұрын

Yes please do I had such a rough time removing my tire from tubeless ready rim

Check the Tires Sidewall Information: "Mount only on hooked rims" is stated on all Continental road tires. As the hook gives you blowoff safety at high pressures! For MTB and Gravel the hookless MAX. is 73PSI / 5bars! Never ever ever exceed it!!!

After 30 minutes of struggle,frustration and cursing. I watched this video and it’s the best thing I could have possibly done while changing tires.

Amazing method!! Thanks so much for the energy and the care

Hahaha. I’ve been there with the sore fingers then I learned this technique. Still takes some effort with my armadillo elite tyres but generally taking your time and easing it, the road tyres seem to pop on when they’re massaged around. Always a great feeling when it’s on a seated. Thanks Harley. Not sure anyone else makes a tyre change quite so entertaining!!

Hardely try the Last 2 hours a Continental GP 5000 with Fulcrum Wind 55 DB rims. But your Video was the Part that worked finally! Many thanks!

that rear hub sounds mental, i want one

one other thing...BEFORE you flip your bike upside down make sure that your GPS doesn't hit the ground or you will get some really serious scratches on it.

Now I know how to change a tire! Thank You!

A thank you from Conti in Germany for the good explaination!

love it works great. just the right size

Cheers buddy informative video with humour 👌

You’re not kidding.. that works.. thanks for the great advice

I can barely understand you but your advice is on point. Thanks!

That was so helpful. My continental tires would not budge until I watched this video. Thanks again

Well done mate

That’s excellent. I never knew this would work those continental tires. They’re so tight thank you for sharing this. I hope to be able to well. I hope I don’t flat but if I have to maybe put it in a gravel tubeless tire and wheel that I could be able to air it up and seat the bead if I ever get a flat I on the gravel and temporarily running some TPU tubes during this hot summer season because I’m not riding the gravel bike much and don’t want to deal with dried up sealant I dread having to do anything but this is fantastic. Thank you. !!!

Thx for your tips👍👍

My continental tubeless tires were super tight too. Was worries we were going to hurt the wheel with the levers because they were so tight. Same wheels

Superb 👏😀. I was struggling to get the tyre on a tubeless rim and as a last resort found this video - and of course it worked! Thanks for a very clear explanation😀

Thank you so much - I've been struggling all day with getting my Vittoria Corsa tyres off my Mavic Ksyium wheels and replacing them with Vittoria Rubino Pro ones - it's been a full on nightmare creating blisters, blood blisters and genuinely making me need a long evening nap! I'm going to try this way tomorrow - thanks so much :)

@durianriders

2 жыл бұрын

Easy combo to put on and off.

@quentendeclercq4792

Жыл бұрын

I had 3 sets of Rubino pros. Man do they test my nerves!! I spent an hour getting it on.

The internet told me once that you should finish the tyre removal or install process at the valve. The theory is that the valve is the point where the tyre will tend to sit higher in the channel and so will give the least slack and hence you want to finish there. Seems to work.

Thank you.

I have the previous SL1 rims they are not hookless, means more tyre choice 👍 good tips Harley

Dope dude

This actually WORKS!!!!!! thank you amazing!!!!! finally

Great video

100%highly correct

Thanks for the video...always seem to have a harder time putting the back wheel back on.

GP5000TL are a pain in the ass

He's right about this 🙂

Nice video

Nice short sleeve top.! I was a long sleeve before it was altered.

The analogies in this video are epic! 😂

This fkning worked!!! First time I got the tire back on with ease and no tools!!! Thanks for the video!

I find if I put the tire under my shoe and try to stretch it by pulling as hard as I can a few times seems to help.

You know how to make a common tyre change utterly entertaining 🤣

Quick thoughts. The Mavic Ksyrium SL aluminum wheelset as an upgrade. Apparently they’ve improved the hubs for 2021. For my 2005 Giant TCR 1. Still has the stock Xero lite xsr-1 wheels.

Can you do a video on how to be happy

Dude. Thank you. 🥹

Great advice. I’m happy that you stopped met S rants. Quality content 👍

F*******g legend

GP 5000TL are a pain in the ass

@durianriders

3 жыл бұрын

I've found them very easy when you use my protocols.

@Freacer1

3 жыл бұрын

I think it also heavily depends on the wheel itself. The bead on the GP5000TL is so wide one side alone almost takes all the space in the center channel of the wheel. Been using this method as well as of course, it gets way easier when the tire is properly in the channel but... on my Syntace W21i rims they were almost perfectly sealed without even putting the fluid in. Was a massive struggle to get them on.

Guess you have not tried to fit vittorias open corsa cx III in 23mm size... That's tight

@durianriders

2 жыл бұрын

easy AF!!!

When is the Focus video dropping ?

Thanks for the tip. Saved me from freezing my ass off up the mountains in Ireland 🇮🇪! 5min tube change today! Usually fighting like fuck to get the tire back on!! Ride disc brakes! 😉😂

The tire goes off easier when you talk to it in an Australian accent.

Hahahaha .. not sure many people could make me laugh out loud changing a tire

What if pedals are on the bike? Is it harder?

Durian I am having serious issues putting on tyres on my new hunt carbon wheels. Never had this problem with my alu wheels Do other people have this problem

check inside tire for for glass or thorn that caused puncture before reinstalling though

@durianriders

2 жыл бұрын

💯🤟

I’ve discovered it doesn’t help to have OCD and ADD while fitting a tire on a tubeless ready rim.

how can you hate this man

I’ve got those rims and run them tubeless with schwalbe pro 1s. I’m a lightweight so run them at 60psi rear and 58 front on 25mm width and they are fine. Notice as well if you do run tubeless you should only run the tyres approved by giant which is quite a small number of manufacturers at the moment.

@CSasgmt2

3 жыл бұрын

May I know what's your weight? I'm 57kg and I pump 80psi rear and 70psi front. I think I could go lower psi.

@pj9375

3 жыл бұрын

@@CSasgmt2 I'm 63kg. I used a calculator on one of the tyre websites to give me those and it works well for me 👍

How is that tubeless but has a tube?

You don’t want the dirt on the through axle and it had a mind of it’s own. 😂😂

Helpful video, thanks! Funny you have a whole tennis court but only one tyre lever! PG comments - but your hat...! 🤣

@durianriders

3 жыл бұрын

The mortgage for this place with so hard to afford I'm down to my last tire lever.

Love this video. The other day I fought with two tires installing them on two carbon wheels, it was ridiculous. It took me and my son 20 minutes each tires. SMH!

Good video as always. I recently got into a problem. I have ICAN aero40 with Conti GP5000 25mm. I find it really hard to make the bead to seat evenly throughout the rim circumference. Had to mount and dismount the tyre to the rim 6 times in order to make it seat evenly. Do you have any tips regarding that? My old no tubeless ready aluminium rims didn't have such problem. It's quite shyte cause if I get a puncture and repair the tyre is going to be a bumpy and unsafe ride. Do you have any tips on how to prevent this? Only tip out there is to use liquid hand soap but this isn't something you can do when you get a puncture at the side of the road.

Dude is too damn funny🤣🤣🤣.

'150 on my way to your mum' made me choke on my porridge! 😂

Did you say "Toight Cwarbon Wims" ?

You’re a lot more experience at this than I am , so I feel bad mentioning it but maybe you should always keep the rotor facing away , less chance of cutting hands and legs , the bladed spokes are bad enough

Hi Harley, can you recommend Novatec Hubs? are they as good as DT240s?

What carbon rims would you recommend for heavy riders between 18-19 stone. I got my tcr and I am enjoying. Durian rider for President

@durianriders

3 жыл бұрын

I don't rate carbon rims if you over 100kg. Get some 32 spoke custom made mavic rims with dt swiss hubs or spinergy Z lite.

@highfived

3 жыл бұрын

@@durianriders Thank you sir . Durianrider for President. 👍🏾👑

@highfived

3 жыл бұрын

@@durianriders how many spokes on both wheels ? I will call a wheel builder tomorrow

I don't get the point of hookless rims man, they're ruining the bike industry and racing little by little.

@hcw199

3 жыл бұрын

Weight saving?

@richardharker2775

3 жыл бұрын

Cars have never had hooks but car tyre construction is way tougher. Carbon rims on the other hand are hard to construct with hooks and too large a percentage are rejected due to the complexities. It is much easier to manufacture a carbon hookless rim and be somewhat stronger. The problem really lies with the tyre manufacturers to produce accurate sized tyres to fit a ETRTO standard sized wheel. Thats why Enve list those better tyre manufacturers as safe.

@hcw199

3 жыл бұрын

@@richardharker2775 Another reason I'm going to stick with my Rim brake and Aluminium wheels!

@nikolozchogovadze

3 жыл бұрын

You just need hooks on a bike wheel. They're just running out of design marketing ideas and start making unnecessary changes.

@richardharker2775

3 жыл бұрын

@@hcw199 Me too. It will be a long time before I change, if they are genuinely good that is.

We had a Young Woman win her age in our 70.3 out here in West Texas, never having changed her own flat yet, she turned Pro and changes them on her Vlog now, well taught by our peers and experience O/O°

you can put 120 psi in hookles rims just not with a inertube then they wil blow of tubless they will not blow off that is te problem with hookles rims they just dont take inertubes that well

@durianriders

3 жыл бұрын

😂😂😂🤣🤣🤣

I like it tight

not tight. the bottom part of the bead covered only about 15mm of rim height. try Easton EA90SL with Specialized Turbo Pro Mondo 21c. the tire bead descends past the entire height of the rim by an extra 10mm..... for a total 40mm below the top of the rim. the only way to get my tire mounted is with heat, baby powder and a VAR tool

Mounting new Continental GP 4000 on 50 mm carbon rims. Impossible wtf

Now do that with a new GP5000 TL... and just for a laugh put a vittoria airliner in it.

The wheel you are literally installing this tyre on is hookless. It is also only meant to run tubes in an emergency. You are also not supposed to use gatorskins especially or any tyre not on the recommeded list. The pressures you would be running in a tube could potentially blow the tyres off those rims

@durianriders

3 жыл бұрын

Rated to 125psi though...

@JasonWatsonDr

2 жыл бұрын

@@durianriders only for the recommended tires - the main difference is that the ones on the approved list have a special bead that does not stretch. It is that lack of stretch that makes them safe. Normal tyres give too much and pop off.

‘Sucked under like a thai bar girl that knows what she’s doing’ Claims gold medal of quotes from this video hahahahaha

150 on the way to your mums house 😂

You gotta go by feelings not the truth 😂

you are the david goggins of the cycling world

@hasben0

8 ай бұрын

Goggins is never this funny😂

Why you buying a tubeless tyre when you’re using tubes? They are way heavier 😉

Question, if i wanna wake up and a big ride right away, what do you recommend i eat? Normally I have a huge smoothie wait 2 hours and go. But I can't do that bc of time restrictions

So what if there used rims LOL

wrong.. you break bead on one side only. then use lever to remove this side from the rim, only then break the other side bead..

@durianriders

3 жыл бұрын

You can do that way if you want. I often put the tire on and off with no levers though

@9snake

3 жыл бұрын

@@durianriders true. if this is not tubeless. I recently was removing my 1 year old TL tires and this method I described worked really good comparing to standard that you described :)

To cut a little on a disc bike, they removed the edge for tyre to hook on?! WTF that is just rediculous!! Save the rim brakes!!

rrrright...

Haha.."Has to be German, the hardest tire to put on".......that tire is LOOOSE compared to many I've dealt with..... That tire literally flopped over the bead. You'll know its tight when you need a lever just to get the first bead on!

@durianriders

3 жыл бұрын

Nah no lever needed if you got skills like me

150 on the way to ya mum’s house 😆😆

Yes you can make it work but even this guy had to work at and make stupid female jokes. It should not be this hard