How to Change A Shower Arm and Flange In 5 Minutes
Тәжірибелік нұсқаулар және стиль
(Heads Up: Thread Seal Tape should be wrapped counter-clockwise on both sides. Video shows tape being applied clockwise from the one side.)
Are you looking to upgrade your old, worn out shower arm and flange? Whether it's just really beat up looking, or you want a different style/length, a shower arm replacement is key to any shower upgrade.
And if you never changed a shower arm pipe before, you may have your hesitations. Unlike a shower head installation, the shower arm pipe is threaded into the wall which can look intimidating. But it's actually super easy!
In this video, I'm going to show you how to replace your shower arm and flange in less than 5 minutes!
I'll be using the highest quality shower arm and flange on the market. And I've used a lot! Trust me, this one is expensive but it's worth the money. Why have a really nice shower head and not have a nice shower arm to mount it on to?
Available on Amazon: amzn.to/4etA6PO
Available at The Shower Head Store: bit.ly/3tmgoSI
The shower arm is made from very hefty brass and the flange is really thick gauge brass which is super rare. What I especially love about this shower arm set is that the flange has a set screw to tighten it down onto the shower arm so it doesn't move around. If you've ever had the flange sliding around on your shower arm, you'll find this very important.
Now, here are the steps to installing your shower arm and flange.
1. Remove your existing shower head
2. Use a utility knife to separate any silicone or plumbers putty from the flange so it's not stuck to the wall.
3. Insert a screwdriver into the hole of the shower arm for leverage
4. Unthread the shower arm counter-clockwise using the screwdriver
5. Take the new shower arm and slide the flange over it
6. Wrap both ends of the shower arm threads with Teflon tape, getting a heaping amount on there. Close to 10 turns
7. Guide the shower arm into the hole in the wall to find the threads
8. Reinsert the screwdriver into the hole of the shower arm
9. Thread the shower arm into the wall by rotating the screw driver in a clockwise motion
10. When it starts to get tight, go around one last turn and square the shower arm up in your shower
11. Slide the flange so it's flush against the wall
12. Tighten the set screw down
13. Seal the edges with silicone
14. Finished!
Let's take a look at this video and put it all together.
***Some links may be affiliate links. We may get paid if you buy something or take an action after clicking one of these.
The Shower Head Store is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.***
Пікірлер: 461
My mother was actually about to pay a guy $1,000 for this job. When I found out I immediately looked up how to do it. Thank you for saving me and my mom $1000. God bless
@nikolasdang5196
2 жыл бұрын
Goshhh $1k how does that guy sleep at night???
@heslind
2 жыл бұрын
Report that person to the bbb
@mjschoensee93
2 жыл бұрын
SMH that is robbery
@JohnDoe-bz4yl
2 жыл бұрын
@@nikolasdang5196 on a bed of cash
@RichardBeaty98
Жыл бұрын
I'd done it for 500
The Teflon Tape was put on in the wrong direction. Pointing the end of the pipe towards you, it should go on clockwise. This is the direction that the pipe threads travel when tightening. Putting the tape on in the counterclockwise direction as shown in this video will cause the tape to bunch up as it is tightened making it useless at providing a seal. I always install these with a temporary cap at the other end and turn on the water to pressure test and check for leaks. If there are no leaks then I replace the cap with the shower head and silicon seal the flange.
@theshowerheadstore
3 жыл бұрын
Hello Paul, you are correct, we've noticed that we've accidentally done that but we are unable to edit the video. The notes will be updated shortly to address this. Thanks for bringing this to our attention.
@audiophileman7047
2 жыл бұрын
Don't you think it would be better to use Tru-Blu Rector Seal Pipe Thread Sealant on those threads? Tru-Blu is great stuff and recommended by plumbers. I really like your idea about capping it off to check for leaks. 👍👍👍
@markanderson77
Жыл бұрын
As I was watching this video, that's the same thing I notice. It is supposed to go on in such a way that when you turn, it goes WITH THE DIRECTION of the tape, not against it. He did this backwards.
@sailbatten2056
Жыл бұрын
I used to think so, but despite the consternation from tradesman, it really doesn't matter that much. I always make sure to put it on the right way, but no, it won't be "useless", nor will any of the bunching up matter. The stuff compresses so easily and it is already by definition a tight fit between fitting and socket threads that there is *_no place for the Teflon to bunch up to._* It's not as if you'll unravel the tape entirely as you turn. Try the same experiments with it that I did and see. You'll not have any catastrophic leaks by putting it on CCW. I avoid doing so, but only because being a purist doesn't hurt anything. But if you forget, it's not the end of the world, and really won't matter _that_ much.
@timothyhedrick5295
11 ай бұрын
Thanks. I thought that was correct as well. Always thought you wrapped teflon tape in the OPPOSITE direction as you are going to thread the pipe/fitting so the end edge of the tape is facing in the opposite direction you are threading your pipe or fitting in/on. Justin cites the correct reason but the wrong direction.
I love simple direct instructions. Thank you!
@theshowerheadstore
2 жыл бұрын
You are very welcome, Faith. Let me know if you need anything else.
Nailed it. 1st Time I ever Attempted -- less than 5 minutes from start to finish [including watching the video!]
@theshowerheadstore
2 жыл бұрын
Thanks for letting us know, Peter & Nicole. We truly appreciate you!
@LilChelle
Жыл бұрын
Please explain that since the video is over five minutes. 5:17 to be exact.
Thank you! Great informative video...did everything u said and I successfully installed my shower arm and Rainfall Shower head without a plumber. Yay!!
@theshowerheadstore
3 жыл бұрын
Hi Garry! Awesome! I'm so glad you were able to do it!
Thank you! I sit on hold with (a certain well known store that sells hardware and appliances) chat for 30 mins last night while they tried to figure out what a shower arm and flange was for me. They came back with an answer that didn't have anything to do with the question instead of just saying, "Idk".
@theshowerheadstore
4 жыл бұрын
That must be an awful experience.
Thanks! Just what I was looking for mainly to see how to remove the pipe. Screw driver trick was key. I probably would have put the set screw on top out of sight (unless you are Shaq.)
Great video. Clear and concise. Thank you!
@theshowerheadstore
4 жыл бұрын
I'm glad it helped you out!
Thank you. That screw driver hint was brilliant
@theshowerheadstore
3 жыл бұрын
I'm glad we could help!
Thank you!!!! I was terrified I'd have to take tiles and wall down. Haha. What a relief!!!
@richardlapoint1845
3 жыл бұрын
My collar has putty around it, so i thought the same thing 🤣🤣
Thank you for this! I had no idea what to do and how the arm was connected (or if it even was connected to anything). Successfully changed an old arm with destroyed threads.
@theshowerheadstore
2 жыл бұрын
You are very welcome, Mary. Please let us know if you need anything else.
Much appreciate that you shared quickly what direction to thread the tape. Gonna do this pretty soon and that’s something I’d easily not pay attention to.
@theshowerheadstore
Жыл бұрын
Thanks for the feedback.
Thanks for taking the time to make this video. Very helpful
@theshowerheadstore
2 жыл бұрын
You are very welcome. Let us know if you need anything else.
Great tips! Thanks! I have a new shower arm to install, and I was worried because it has threads on both ends, and I thought I might need some kind of connector... happy to see yours looks the same, and I am good to go. What I did with the flange, is I put beads of clear silicon, inside the back of the flange, in ever larger circles, until it reached the very edge of the inside of the flange, and made sure, the last circle, rested slightly above the edge of the flange, so when installing this, pushing on the flange, with just a little pressure, compresses the silicon slightly, because silicon is flexible, and that makes for a perfect watertight seal, and you can't even see the silicon on the inside. I wouldn't use plumber's putty on marble, (Plumber's putty is greasy.) as marble is a soft, porous stone, and the marble will absorb the oil from the plumber's putty, and the marble will stain around the flange. It is probably fine to use it on granite.
@theshowerheadstore
Жыл бұрын
Thanks for your feedback. I am happy we were able to help you.
I just want to said thank you so much dude. You safe me a huge headache and was easy to do the job
@theshowerheadstore
2 жыл бұрын
I am happy to help Oscar. Let me know if you need anything else.
Thanks brother, very helpful video...made my job of replacing an old shower arm very easy.
@theshowerheadstore
Жыл бұрын
Thanks for the feedback, Joseph!
Thanks for this tutorial. The only thing I don’t like is seeing a hole at the bottom if the flange. I wish we had a piece to cover it. Otherwise, very great quality
@theshowerheadstore
2 ай бұрын
Thank you for the feedback!
Thanks for the simple and fast how-to instructions
@theshowerheadstore
3 ай бұрын
Anytime! We are happy to help!
Thanks guys, very helpful.
Thank you for this ! My arm was leaking ! Was able to remove and retape to stop the leak!
@theshowerheadstore
3 жыл бұрын
I'm so glad that you were able to make it happen!
Exactly the video I needed. THANKS!!!
@theshowerheadstore
3 жыл бұрын
We are so glad that you liked it!
Nice Video. Simple and Straightforward 🤙
@theshowerheadstore
Жыл бұрын
Thank you John!
Nice job explaining this replacement.
@theshowerheadstore
2 жыл бұрын
Thank you, Yvonne. Please let me know if you need anything else.
Thank you!! I changed my shower arm myself. Saved plumbing cost !! Hurray
@theshowerheadstore
3 жыл бұрын
You are very welcome. Let us know if you need anything else.
Thank you so much Justin!! These tips help everyone so much!
@theshowerheadstore
Жыл бұрын
My pleasure, Cher!
Thank you sir! Easier than I thought.
@theshowerheadstore
4 жыл бұрын
You're welcome :)
Thank you, this was very helpful
Thanks. I just change my showerhead & now thinking of changing to L-arm too.
@theshowerheadstore
3 жыл бұрын
You are welcome! Please let us know if you need any help!
Thank You, love the screw driver tip. saves from taping the pipe for wrench maring...
@theshowerheadstore
2 жыл бұрын
Thanks for the feedback Greg and you are very welcome.
So simple! Thanks for sharing!
@theshowerheadstore
2 жыл бұрын
You are very welcome. Let me know if you need anything else.
GENIUS. I was debating if I'd need to cut out a piece of the wall :))))
You made it look so EZ. Thank you.
@theshowerheadstore
3 жыл бұрын
Glad to help!
Thanks Justin for all of the good tips, especially about wrapping the tape on the pipe ends in a clockwise direction. I pretty much knew that I would be using a screwdriver placed inside the pipe to unscrew the old arm and installing the new one. However, there’s one thing you left out that’s important for some DIY’er’s like myself to know. When installing the new shower arm, the longer end goes into the wall with the shorter angled end pointing out and down towards the bathtub or shower floor. 🛀🚿
@theshowerheadstore
Жыл бұрын
Thanks for the input and I am glad we were able to help you.
@oldyellerschannel4676
Жыл бұрын
He installed it that way, if people were paying attention. Plus, you could see the longer end was inside the wall, when removing the old shower arm.
The screwdriver tip really came in handy thank you !!!
@theshowerheadstore
2 жыл бұрын
We are happy we were able to help, Chris. Let us know if you need anything else!
Thank you so much! Your video is very useful!
Thanks for this video!
Thanks so much! This is just what I needed to know. I'll check out your store on Amazon! Cheers!
@theshowerheadstore
3 жыл бұрын
Thank you very much! Please let us know if you have any doubts.
Genius screw driver trick!!! Thank you!
@theshowerheadstore
2 жыл бұрын
You are very welcome! Please let us know if you need anything else.
Thank you so much! Saved us a plumbing bill!
@theshowerheadstore
3 жыл бұрын
Awesome! I'm so glad I was able to help!
Thanks guy just what I needed to know
@theshowerheadstore
4 жыл бұрын
Glad we could help.
Thanks! That's exactly what I needed to know.
@theshowerheadstore
2 жыл бұрын
Thank you. We are glad we are able to help!
This little kzread.infoUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.
Thank you for the video - I wouldn't have thought to use the screwdriver for leverage. I suck at home repair, but youtube helps!
@theshowerheadstore
2 жыл бұрын
You are welcome Tony. We are happy we were able to help!
Helpful video thanks bud
@theshowerheadstore
3 ай бұрын
You are very welcome!
3/17/21: this video is just what I needed. Very clear...thank you~
@theshowerheadstore
3 жыл бұрын
Wonderful!
Nice bro that looked easy, thanks. Side note you look like Derrick on the movie Stepbrothers 🤣
@georgemikodesigns
3 жыл бұрын
He’s headed to the Catalina wine mixer next!
Love the screwdriver trick. Thank you.
@theshowerheadstore
2 жыл бұрын
You are very welcome and thank you very much! Please let us know if you have any other questions.
Wow I never knew this stuff was this easy thank you for this video now I can finally go ahead and change my shower head cause I was a bit nervous about how to change it
@theshowerheadstore
Жыл бұрын
I am happy to we were able to help you with this, Naeema. Thanks for the feedback!
Love your video, very expletives.
@theshowerheadstore
2 жыл бұрын
Thank you
Very helpful. Thank you
@theshowerheadstore
2 жыл бұрын
You are very welcome, Keesio. Let us know if you need anything else.
Me, my mother-in-law & her guest bathroom thank you!!! Cheers!
@theshowerheadstore
3 жыл бұрын
I'm so glad that I was able to help!
@richardlapoint1845
3 жыл бұрын
@@theshowerheadstore thanks for the video, im gonna be replacing both arms and shower heads
Thank you. Got an idea 🙏🏻
@theshowerheadstore
Жыл бұрын
You are very welcome!
Very nice video. Thank you very much.
@theshowerheadstore
2 жыл бұрын
Thanks for letting us know Scotty. Please let me know if I can help you with anything else.
Thanks so much! You saved my marriage.
@theshowerheadstore
3 жыл бұрын
We're glad to be of service!
Thanks brother.
Hi. Are there specific tools design to remove snd install shower handles and heads? The plumber had to come fix my shower and he scratched the handles now I have to replace two of them and I cringed of the thought of installing them and scratching them. I hope you can reply. Thanks
thank you, helps a lot😊
great trick with the screwdriver. thanks!
@theshowerheadstore
2 жыл бұрын
Thanks for the feedback Todd and you are very welcome.
Thanks man! Really helped😎👍
@theshowerheadstore
Жыл бұрын
You are very welcome!
Great video thanks.
@theshowerheadstore
Жыл бұрын
Thank you, James!
Thanks for the típ on how to get the old arm shower off! 👌
@theshowerheadstore
2 жыл бұрын
You are very welcome. Let us know if you need anything else.
THANKS I'm on it
Thanks for the video. Should take the set screw and place on top so it is out of sight.
@theshowerheadstore
2 жыл бұрын
You are welcome and thank for the honest suggestion!
very good video, show to the point, I have a question to ask do I need to shutoff the main water, before doing this, thank you very much Gbu
@chole4me1
4 ай бұрын
No, the water is already off at your shower knobs
Thank u so much. U guys helped me so much.
@theshowerheadstore
Жыл бұрын
You are very welcome!
Thanks for the detailed video. Question: Do you need to turn off the water supply to change the arm?
@temarmalcolm1741
3 жыл бұрын
Once your shower trim is already turned off you should be fine.
Do I have to shut off the water valve? This is just what I needed to know. Thanks
@theshowerheadstore
3 жыл бұрын
You do not need to shut off the main supply to change out your shower arm, you just need to shut the water off at your shower valve. There should be no water coming out of your shower head when performing this change.
Thank you so much I'm 62 and I have to do it myself Thank you again.
@theshowerheadstore
3 жыл бұрын
I'm so glad that i was able to help!
@NaturalMonty
3 жыл бұрын
me too at 66...yuk!
Great video! Thanks so much. Just wondering if you did mention the brand/model name of the new shower arm and flange you used, as you said you would? (If so, I can't find it in the video.) I need to replace my original, 72-year-old arm and flange, and I like the one you used. Thanks in advance!
@theshowerheadstore
2 жыл бұрын
This is a Speakman Neo S-2540 Shower Arm and Flange, 7", Polished Chrome and it can be found on our website here: www.theshowerheadstore.com/collections/accessories/products/shower-arm-and-flange-with-set-screw?variant=38136115888321
These type of repairs/updates always scares me. I don’t like not knowing if my pipe is leaking being it’s behind a wall. I know folks will chime in and say if you put teflon on correctly and tightened it correctly, yadda, yadda...Things can still go wrong beyond your control, like age of pipes, condition of threads, etc.
@mazaspan3025
3 жыл бұрын
Same, like what do I do, if I can’t screw it back on.
@theshowerheadstore
3 жыл бұрын
Hello there. A lot of things can go wrong such as what you mentioned in terms of the age of the pipes and the condition of the threads in the wall, and in this case, I would recommend that you add extra turns of tape or consult a plumber to check on leaks in the wall.
@DalTexGuy
Жыл бұрын
Thanks Justin for all of the good tips, especially about wrapping the tape on in a clockwise direction. I pretty much knew that I would be using a screwdriver placed inside the pipe to unscrew the old arm and install the new one. However, there’s one thing you left out that’s important for some DIY’er’s like myself to know, when installing the new shower arm the longer end goes into the wall with the shorter angled end pointing out and down.
@jackeroo75
Жыл бұрын
@@DalTexGuy why can’t it be the opposite?
@fuimaygeetang
Жыл бұрын
Leaks inside the wall is my main worry. I'm guessing the thread is not standard like on the shower end of my old one.
Thanks 😊, u saved a lot of things 😅.
@theshowerheadstore
3 жыл бұрын
Hi Halawyey! That is so nice to read!
Thank you for explaining the direction of the tape in a way my adhd brain could comprehend 2:39 😭 God bless you baby
@theshowerheadstore
9 ай бұрын
You're so welcome and thanks for the feedback! I'm thrilled to hear that the video helped you out, and I totally get how important clear directions are. God bless you too! 🙏💙
I always lived an a apartment. I recently just bought a house. I need to learns some of these do it Yourselves and I'm kinda nervous. Two questions. 1) if i take everything off, is that what's usually behind the flange a hole in the wall I assume in that hole a is a pipe you just stick the arm to? 2) are shower arms universal? Thanks again. Might be dumb questions but I just want to learn everything. I'm new to this
@theshowerheadstore
4 жыл бұрын
1. Yes, there is usually a 1/2" Female Pipe Thread connection in the wall. That's the standard in the USA. 2. In line with the previous question, shower arm pipes are a standard 1/2" Male Pipe Thread. There may be some exceptions, but the vast majority of the time you're dealing with these standards.
@Pshady23
4 жыл бұрын
@@theshowerheadstore thank you so much
@theshowerheadstore
4 жыл бұрын
@@Pshady23 You're welcome!
Awesome, thank you this was exactly what I needed :)
@theshowerheadstore
4 жыл бұрын
You're very much welcome ;-)
If I tighen it too far will the diverter valve bust and squirt water everywhere ? If feels like the arm has hit max but it's pointing toward the ceiling. And if I back it off until it points down it's lose and leaks. I've tried two different arms with the same result.
@theshowerheadstore
10 ай бұрын
Of course, I'd be glad to help you with your shower arm installation concerns. It sounds like you're dealing with a common issue when installing a shower arm. Tightening the shower arm too much can indeed damage the pipe and potentially lead to leaks. On the other hand, if it's not tightened enough, you'll experience the arm being loose and causing leaks as well. To ensure a proper installation without any leaks or damage, follow these steps: Wrap the threaded end of the shower arm with Teflon tape. Use at at least 5-8 wraps if 3 wraps not working out. This helps create a watertight seal and prevents leaks. 3. **Hand Tighten:** Start by hand-tightening the shower arm into the threaded pipe coming out of the wall. Turn it clockwise (righty-tighty) until it's snug against the wall. 4. **Use a Wrench:** Once the arm is hand-tightened, use an adjustable wrench to gently tighten it another 1/4 to 1/2 turn. Be cautious not to over-tighten, as this could damage the threading or the pipe inside the wall. 5. **Alignment:** Ensure the shower arm is aligned correctly. It should point downward, perpendicular to the wall. If you find that it's pointing toward the ceiling, you may need to use an additional piece like a shower arm extension to achieve the correct angle. 6. **Sealing:** If you're still experiencing leaks after proper tightening, consider using plumber's putty or a rubber gasket. Apply a thin layer of plumber's putty around the base of the shower arm before tightening it. Alternatively, some shower arms come with rubber gaskets that should be placed between the arm and the wall. 7. **Test for Leaks:** Once you've completed the installation, turn on the shower and let it run for a few minutes. Carefully check for any leaks around the connection point and the wall. If you notice any leaks, you might need to repeat the process, ensuring proper sealing and tightening. Remember, it's important to find the right balance between snugness and not over-tightening. If you've tried multiple shower arms with the same result, the issue might be with the threading of the pipe itself. If that's the case, it's a good idea to consult with a professional plumber who can assess the situation and provide a proper solution. If you're not comfortable with the installation process, it's always best to seek help from a licensed plumber to avoid potential damage or water leakage issues.
What did you do at the end to secure/tighten the flange?
@theshowerheadstore
4 жыл бұрын
There is a set screw in the flange that you tighten down onto the shower arm so it does not move.
THANK YOU
@theshowerheadstore
3 жыл бұрын
And you!
how do you ensure it doesn't leak behind the wall? with the actual shower head it will be obvious since the threads are in front of the wall, but the arm goes behind the wall.
@theshowerheadstore
4 жыл бұрын
Put a ton of thread seal tape on the threads and tighten it down as much as you can. The female connection in the wall has pretty deep threads, so you shouldn't have a problem getting it to be watertight if you make sure you give the shower arm enough rotations.
There was rust and orange gunk in my pipes. Alot of people are showering in Galvanized Steel rust water. If your eyes feel irratated after a shower its because of the rust. I noticed after I removed the shower arm. Im going to have to remove the caulking, chisel the tiles off my wall, break through the drywall with a oscilltating tool, then change out the piping.
I have a question, do you have to first shut off the water before you change this out? I live in an apartment and it would be virtually impossible for me to shut the water off to my building just to change this out.
@theshowerheadstore
3 жыл бұрын
You don't have to shut off the main water to change this out, although it's never a bad idea just to be safe. You only need to make sure that your shower valve is closed all the way and that no water is coming out of your shower head. Then you'll be good to go!
I have a question about the shower mount i have a old shower head with a ring that has a thread in it do i need to remove the shower arm to remove the ring
@theshowerheadstore
Жыл бұрын
It could be one of those old price pfister shower arm holders built into the shower arm. If that’s the case, you’ll need to replace the shower arm too.
I like the tip on using a screwdriver.
@theshowerheadstore
2 ай бұрын
Thank you for letting us know!
What if I turn that original shower head arm lose one half turn so that it’s angled upward for a shower head I’m installing? Am I risking leaks with this arm half turned lose to have it angled upward?
@theshowerheadstore
4 жыл бұрын
There's always a risk of leaks if a component is not fully tightened down. In this case, I would suggest using a heavy amount of thread seal tape on the end of the shower arm going into the wall. That way you can mitigate the chances of any leaks while still being able to have the shower arm pipe pointing up. Do your best to thread the shower arm as far into the wall without damaging the internal plumbing. The screwdriver technique outlined in this video will help out big time.
The Allen screw holding the new flange would look best if installed on the top side where it can't be seen. Just a thought. Good video.
@theshowerheadstore
Жыл бұрын
Thanks for the feedback, John and you are very welcome.
This helps a lot! Why are shower arms so damn short in the first place? I'm installing a longer arm. You can't hang a rack on it because all of the water drips into the soap dish and makes a mess.
@lozoft9
2 жыл бұрын
Are you in a rental or a cheaply-built house? Oftentimes contractors/developers/landlords will skimp on pieces like this to save a buck, but thankfully it's very easy to upgrade without risking damage.
@davidhalley9795
2 жыл бұрын
@@lozoft9 It’s a brand new house and wasn’t cheap. It’s a spec house and we had no say in the accessories, paint, color, fixtures etc. Yes, it’s an easy thing to fix.
The connection between my shower arm and the wall is on the inside of the wall.how do I apply taflon tape to that
@theshowerheadstore
3 жыл бұрын
Hi Andy, That is a great question. Most Shower Arms have the male end on your side, So you can place the teflon tape on the shower arm and screw it on. I hope this info helps!
Which part of the thread do u start wrapping the tape onto:the bottom of the thread where it meets the arm or the top where the 1st thread is that goes into the fitting?
@theshowerheadstore
Жыл бұрын
You will start wrapping the tape on the male threads from the part that goes in the females threads first.
I just used channel locks and scratched my antique bronze arm. Lol. Wish I would've seen the screw driver trick before. Ha ha.
@theshowerheadstore
2 жыл бұрын
I am sorry to hear that Bob. If you have any other concerns, do not hesitate to reach out.
Any tips on what do you do if the plumber didn't secure the pipe properly behind the wall & you don't have access? I'm afraid if I take this shower head pipe out (which was installed incorrectly so it's leaking & if I tighten the pipe it points to the ceiling) I'm going to loose whatever it attaches to. Bought my house with it like this.
@theshowerheadstore
2 жыл бұрын
Hello Jenna, if the plumber didn't install the fitting correctly then I would get that same plumber to correct the problem
Good vid.
@theshowerheadstore
4 жыл бұрын
Thank you!
Do these instructions apply when the neck portion snapped off from the pipe inside the wall?
@theshowerheadstore
10 ай бұрын
Hi! In that case, we would definitely suggest to use a plumber to prevent further damage
Do you have to shut off the main water source for the house to do this? Or just keep the shower faucet shut off?
@theshowerheadstore
3 жыл бұрын
You can just keep the faucet off. No problem! :D
I like the screwdriver trick.
@theshowerheadstore
2 жыл бұрын
Thanks for the feedback, Jacob.
Saving me a plumber's $$ visit. Thank you!
This would be helpful except my shower pipe is like a foot and a half long and won't yank off. Any advice on longer ones. I'm trying to install a short one
@theshowerheadstore
Жыл бұрын
The same procedure should work but you could also us a wrench.
Thank you very much
@theshowerheadstore
3 жыл бұрын
I'm glad that you liked it!
@dutchesscarniegegordon56
3 жыл бұрын
@@theshowerheadstore you are welcome I apply it today and install my new shower head. Save me some money. I'm very grateful. Thanks again
What if it's a hard 90, straight down off the wall ? I cannot find any other fitting like it.. It is around 10-13 years old. Made with a vacuum fitting that attaches and then a handheld & hose - attached to a grab bar. I'm wanting to delete this and make a normal angled showerhead.
@theshowerheadstore
4 жыл бұрын
You'll need to remove the 90 degree fitting (wall elbow/drop ell). There is likely a short nipple threaded into the wall that the wall elbow threads onto. You'll also need to remove that. Then, you should be able to install this type of shower arm without a problem.
We recently replaced the shower hose/ head because ours was filled with calcium , our water is awful. It was fine but now is leaking between the shower arm and where it goes into the wall, where the shower arm connects to the main pipe. We’ve tried re-taping it to no avail. Any ideas on how we can fix this leak?
@theshowerheadstore
3 жыл бұрын
Hi Angel, it seems that the calcium deposits were also lodged in the shower arm. In this case, I would suggest a new shower arm and try it out. If this doesnt work out, it might be that the threads in the main pipe might be damaged. in this case, it would be better to use "plumber's putty" to have it fixed.
i'm looking to change my shower head and arm and never did it before so have some questions.are most shower heads and arms the same size. Or are they different sizes? or is there a comon size that they may be
@soothingstyles8749
3 жыл бұрын
Most, if not all shower arms have a standard 1/2" male pipe thread, and a standard showerhead has a 1/2" female pipe thread
The hinge of the shower arm broke and the little piece of the hinge is still in the thread inside how do i remove it
@theshowerheadstore
4 жыл бұрын
Let me clarify. Are you saying that the threaded piece of the shower arm broke off inside of the wall? If so, you'll need to a special tool called a Shower Arm Thread Remove to extract that peice. There's a great video on KZread on how to do so. kzread.info/dash/bejne/gHik0sOCYbXIeMY.html You can always email us at contact@theshowerheadstore.com or reach out to us through Facebook Messenger @theshowerheadstore.