How to Change a Safe Combination Without Using a Locksmith
If your safe has a dial, you can change the safe combination youself, so long as you know the existing combination.
Suggested Videos:
How to Dial a 3-digit Safe Combination
• How to Dial a Safe Com...
How Safe Combination Locks Work
• How to Open Safes With...
In this video we walk you through dialing a safe combination and demonstrate how to change a combination of a safe.
To perform a safe combination change, you need the combination change tool. Normally this tool comes wit the safe when you bought it, but sometimes it does not.
The reason the change tool may not come with the safe is because if something goes wrong while you are changing the safe combination, and you close the safe, you will be locked out. At that point, a locksmith will be required to come out and drill the safe then replace the dial lock.
Drilling a safe is VERY expensive, so before attempting to change your own safe combination understand these two things:
1) You should understand the risk of changing a dial combination to a new combination.
2) You should always test test the new combination with the safe door open. This way, if it did not work and something went wrong, a locksmith can come out and reset the combination.
Пікірлер: 58
Thank you soo much. i've looked all over youtube for a video like this and there is nothing good. I have some combos i need to change on a couple AmSecs
One trick I use when changing a combination is to put a bit of electrical tape over the top mark. So that you don't get muddled up when setting a new combination. Don't forget the other rules numbers must be at least 5 digits apart and the last digit should be at least 10 away from the unlock number 0/25/50/75 depending on what it is on your safe. 😀
@LocksmithRecommended
2 жыл бұрын
Great tip! I should have included that!
@fauxque5057
2 жыл бұрын
The electrical tape is the key. You get so used to dialing to the normal stop that it's just natural to be drawn to it. A little tape and I was good to go
@IGATECK
2 ай бұрын
The last digit should be at leat 10 away from the "unlock number"? which is the unlock number? is just a 3 sets of numbers right?
Robert, We would love for you to make a video for changing the combination on a S&G 8500 series high security lock! Thanks for considering this new task!!!!
@LocksmithRecommended
9 ай бұрын
Same process.
Any help is appreciated...this video helped me successfully change the combination (I tested it 3 times with success as well), however, I cannot get the dial to move anywhere besides through the 80 and 90s. I can lock and unlock but only if it's back on 80? I can't get my key to turn either. Not sure what's happening.
With door open and messing with the combination, put a 2x4x 3’ long in the safe KEEPING THE DOOR FROM CLOSING! With a long enough 2x4 in the opening of the safe keeping the door from closing, do all your messing with the dial the combination until after locking it (with2x4 keeping door from closing) and manipulating the dial you successfully cause the handle to open the bolts - at least 5 complete times - also have another person do the combination, and successfully have the handle turn to retract the bolts - have person do this at least 3 times successfully. THEN and only then remove the long 2x4 that then allows the door to close to lock it. If you don’t understand this , don’t mess with your combination lock safe. There’s a misconception that a ‘locksmith’ can open your dial combination safe if you close door and lock it without successfully testing combination WITH DOOR OOEN. Wrong. No one can open your safe with the dial if you’ve screwed up the dial combination and lock a closed door!
I have safe with opened door, locked is block, I don’t have key, I don’t know code. I have access to key hole. Is anything what can I do myself?
@LocksmithRecommended
Ай бұрын
Call the manufacturer of the safe. See if they will ship you an override key and give you directions to reset the combo. If that doesn't work take the door into a locksmith shop and they can do it for you.
Hello how's everything What is the name of that key did you say "change key" ?
My safe doesnt have hole
My Gardal that I bought for the office didn’t come with a change key! Where do I find one?
How. To set new combo on elsteonic keypad and reset button on back of door
If you have two Yale assure locks in the same room, can you use one Wi-Fi module for the two door? Do you need a Wi-Fi module if you are using Apple homekit hub with Bluetooth range?
@LocksmithRecommended
2 жыл бұрын
Questions that detailed are going to be best served by talking to Yale customer support. I've never used the setup in either of these ways.
are dial combos more or less effective to keep burglars out as compared to other style locks?
@LocksmithRecommended
Жыл бұрын
We wrote the article on it. www.acmelocksmith.com/safe-dial-vs-electronic-lock/
Will this work for a liberty safe mechanical combo?
@LocksmithRecommended
9 ай бұрын
Should.
Will this work on a SentrySafe? I don't see a change index, but it does look like there is a hole on the back of the door behind the dial.
@LocksmithRecommended
Жыл бұрын
Maybe. A lot of sentry safed will not let you set to any combination, you have to use one of the presets values. Just depends on which one you have.
Is it possible for a safe dial lock like this to have 2 different combinations to open it?
@LocksmithRecommended
9 ай бұрын
Nope.
Where can I get a change key for my LaGuard tumbler lock?
@LocksmithRecommended
Жыл бұрын
Amazon. amzn.to/3ePAEVQ I do get a small affiliate commission if you buy using that link.
@dickeymoore3662
Жыл бұрын
@@LocksmithRecommended ok Thanks
Is it possible to change the combination if you dont know the current one? Im wondering if someone drilled a small hole in the safe could someone stick a tool in the combination key hole and change it to something else? I wondering if i should put tape or something in front of that rekey hole
@LocksmithRecommended
7 ай бұрын
It is, but it's much more difficult. Take it to a locksmith.
@killer2600
5 ай бұрын
Someone can always drill a hole in the safe but you can't follow this combination change video if you don't know the current combination to the safe. It's not only required as part of the change process but you need to open the safe so that you can get to the back of the lock where you insert the change key. So there's no reason to put tape over the change key hole.
Can you buy the change key? Or do I need to hire a locksmith??
@LocksmithRecommended
9 ай бұрын
You should be able to pick them up online. Just search for the brand of lock you have.
Hello good afternoon I was chenging my saf combination But I messed Could you please help Thank you very much
@LocksmithRecommended
11 ай бұрын
Call a local locksmith. 👍
Where can you get a change key?
@LocksmithRecommended
Жыл бұрын
If your safe didn't come with one, you'd have to order it for the dial you have.
I inherited a safe. I don't have the old combination, but it IS OPEN. Can I still create a new combination, without knowing the old one, on an open safe?
@LocksmithRecommended
11 ай бұрын
Yes. You'll need to have a locksmith out or take the door into a locksmith shop. They can reset the lock and put in a new combination for you.
Where can buy this changing key?
@LocksmithRecommended
5 ай бұрын
Depends on what type of lock you have. Here's the S&G change key on Amazon. www.amazon.com/dp/B078YDX1WL/ref=cm_sw_r_as_gl_apa_gl_i_33F590Y9CNXTHCCNF07F?linkCode=ml2&tag=acmelocksmithyt-20
What causes all the comb numbers to shift one number? Ie : 35-45-55 is now 34-44-54....
@LocksmithRecommended
7 ай бұрын
It's called drift. Have a locksmith service your dial. Before it drifts so far off that you won't be able to get in.
Hey 👋 so I did this and the new number works. But now it won’t spin and stay locked. It just moves between 2 number and slides the lock in and out. But it will not spin and lock. Do you know what might be causing this? And I can’t reset it because I can’t spin it 😮 Thanks
@LocksmithRecommended
Жыл бұрын
If you can, lift the door off the hinged and take it to a locksmith shop. Something has definitely gone wrong there.
@LockpickingLoser
11 ай бұрын
You probably set the last number in the forbidden zone. This was not discussed in this video. If the last number is set between 0-20, the lock will get stuck when dialed open, depending on the brand.
@LocksmithRecommended
11 ай бұрын
@@LockpickingLoser Valid
What if I don't have the combo?...
@LocksmithRecommended
3 ай бұрын
If the safe is locked you will need to drill it. If the safe is open a locksmith can come and set a new code for you.
Mine has to be pushed in on a 4th number then turned to the right until it stops.
@LocksmithRecommended
2 жыл бұрын
That is another style. This type is the most popular. Thanks for watching.
@onesilentarrow
2 жыл бұрын
@@LocksmithRecommended ok. How do I change my style of combo?
@LocksmithRecommended
2 жыл бұрын
@@onesilentarrow you'd have to change the lock itself.
so there's no way to do this without knowing the exsisting combo? even if the door is already open?
@LocksmithRecommended
6 ай бұрын
If the door is open you would have to decode the existing combo in order to change it. A locksmith can do that for you.
@killer2600
5 ай бұрын
There are KZread video's that cover the topic, sorry don't know any off hand.
Well I know know what that second index mark is for!
Mashaa Allah