There is a mistake in our subtitles and we want to apologize for any inconvenience caused! We used XZN socket bits instead of Torx socket bits. Thank you for your understanding! Yours truly, AUTODOC team.

Don't mind the nit pickers i think your videos are a great resource. Keep putting them out

@autodocuk

5 жыл бұрын

Thank you for your comment! We really appreciate your positive feedback about our work, stay tuned for more! Best Regards, Autodoc Team.

very helpful video ;)

Thankyou for posting this vid, I changed the wheel bearing on my superb today using this vid as a guide and it all went reasonably well. Can I suggest one thing for future vids, can you please post up a list of the tools needed, (i had to go through this vid taking notes of all the sockets/torx etc and having them listed would really have made it easier.)

@autodocuk

Жыл бұрын

In the new videos, we have already fixed this, we will be glad if you rate the new videos.

very informative is it easy to knock of the old one even on an older model

Tanks 👌👌

@autodocuk

6 жыл бұрын

Thank you for the feedback! We are glad you find our video interesting and informative. Stay tuned. Best regards, Autodoc.

Nice video m8. Do you know if the Mk2 seat Leon is the same and don't need a press as it is whole hub. Thanks m8.

@autodocuk

6 жыл бұрын

Thank you for the feedback! To give you an answer, we need to know more information about your car and its configuration. There will be no fundamental differences, however, some nuances may differ depending on the vehicle modification. Stay tuned and follow our latest updates. Best regards, Autodoc.

Nice video, very instructive. But where is the Torque Wrench?

@autodocuk

7 жыл бұрын

You are absolutely right. All the main bolt connections must be tightened with a torque wrench. This video is considered to be an informative one, so it just shows the sequence of repairs. Best regards, Autodoc.

@guusbouwmans5667

5 жыл бұрын

Just AGADAGADAGADAGDAGDGAGDGAGDAGDADAGA the shit out of it hahaha

@230915617

4 жыл бұрын

I have an issue with my Skoda superb mk2 at the moment. I put 4 new tyres on the car and noticed right away that it was pulling left. Got the alignment done and it still pulls to the left. The garage said it might be to do with a bad tyre. So I bought another tyre but now I don't know which tyre is the bad one. Any advice?

@andrew19682008

3 жыл бұрын

So the skoda bearing is easier to replace than an a5? Typical

Does anyone know what the torque settings are pleas4

Do you need to do tracking after replacing the wheel bearing?

@autodocuk

2 ай бұрын

Yes, it is recommended to adjust the wheel alignment after this replacement.

Dobry den, na praci s demontazi/montazi loziska neni potreba stahovak a pripravek pro nalisovani? Dekuji.

@autodocuk

8 ай бұрын

Ano, je třeba použít stahovak a pripravek.

Why hasn’t the mechanic torqued the hub nut? That’s only hand tightened. How so ???

Do you know why some hub bearing carrier has 3 mounting bolts and some have 4? So there is no need to remove the ball joint for access?

@autodocuk

Жыл бұрын

We do not have such information, we recommend that you consult your mechanic.

is it as easy to knock the old one off even on an older model

@autodocuk

8 ай бұрын

We cannot show all the nuances and problems during replacement since this is all individual and it is not always possible to solve them at home. To avoid this, we always recommend that replacements should be carried out by specialized car services.

Does this go with this car ? Škoda Superb Kombi 2.0 TDI 4x4 DSG Sekventiell, 170hk, 2014

@autodocuk

9 ай бұрын

In general, the replacement will be similar, the only thing that may be slightly different is the design features of your car. More accurate information can be found in the technical documentation of the car or by contacting a service center

Shouldn't you use a press to push the new bearing into place? Why have you used new spline bolts and not reused the old ones?

@andrew19682008

3 жыл бұрын

Because they are single use.

@samcash123

2 жыл бұрын

No because the bearings in this instance come pressed into there housing already, you are changing the housing with the bearing already fitted.

Elhiszem hogy ilyen egyszerű de lègkulcsal nem lazulnak a kerèkcsapágy 4 csavarja,nemhogy mèg hosszúszárral,😅😅😅

@autodocuk

10 ай бұрын

Tisztelt Patrik Teljesen igazad van, minden időigényes munka, hogy időt takarítcsunk meg a videón minden elő van készítve. csavarokat be kell fújni sprayel, aminek állnia kell hogy könnyebben kijön a csavar. A következő videóban ezt is megemlítjük Tisztelettel AUTODOC csapat.

And I foolishly tighten the screws with a torque spanner....