They have been working for 105,500 miles so far updated - 4/2/23 215K miles on the car - car has since been sold so there will be no more updates but the coil packs were still going strong 👍👍

@spinb

4 жыл бұрын

Good work. This is a helpful video. I figured that leaky valve cover would've soaked the coil by now.

@TheSundaeDrive

4 жыл бұрын

Probably has lol

@cristobalcardona5592

4 жыл бұрын

Should had replaced the leaky gasket while in there!

@TheSundaeDrive

4 жыл бұрын

Agreed, told my buddy that but he just wanted to get the job done and not worry about it

@cristobalcardona5592

4 жыл бұрын

@@TheSundaeDrive he's probably going to sell the car and it will be next owner's problem!

Hello, Trained as a mechanic in 1980. I've watched many videos, and yours is one of the best. Very well done, excellent camera work. The only problem is you make it look too easy and left out all the mandatory cuss words! Keep up the great work! Edit- just did this job today, the wiring harness near the firewall is a nightmare to work around. I broke every single clip on the 7 connectors I had to disassemble to get at plug#5 because the harness on the 2007 es350 is so tight to the manifold. I wound up buying the gear wrench sockets you used but as it turned out I didn't need them at all I was able to use a standard spark plug socket and a combination of a 4-in a 1-in and a 2-in extension to get into the spark plug well. Using this method you cannot stick the extensions into the well assembled You have to put one in at a time and attach the remaining extensions one at a time and then attach the ratchet last.

@davido3403

5 ай бұрын

What did you have disassemble? I seen other videos taking a whole lot of stuff apart and don't want to go thoough that if I can avoid it!

Thank you very much. I followed all the instructions on the video and just completed my 07’ es350 with practically no problems

The best video for spark plugs I seen , you saved me a lot of time

@TheSundaeDrive

3 жыл бұрын

Awesome!

@superbri007

3 жыл бұрын

And money... my dealership wants $1200. I’m not sure if that included new coil packs, but either way.... I’m going to DIY.... or DIMY, rather.

I only changed the plug and the ignition coil that was bad. Not all of them. Thanks for the video. Great tip.

Thanks for posting this vid! I Replaced back 3 coils on my 2007 Camry SE using this method today. I have done spark plug replacement removing the intake as well and this method is a little quicker. It took about an hour and a half (could do it in under an hour next time) and saved having to replace the intake plenum gasket. The procedure is very close to this video with a few exceptions: 1.) Strut support is more of a tray not a bar. 2.) Wiper motor assembly HAS to be removed in order to get the tray out. Not a big deal just 4 10mm bolts. 3.) Did not remove the L shaped harness support bracket on the left. The harness was taped into a plastic bracket so I cut the tape which allows it to be pulled out. I put a wire tie on it to re-secure it. Number 5 is a PITA but with patience and finesse can be done.

Great video for the do it yourself mechanic. Most videos and forums are showing the torque pounds at around 20 to 21 foot pounds. I checked in a Lexus service manual after you said it was 13 and YOU are correct. Thanks for saving me from stripping out the plug threads in my ES350 cylinder head.

@TheSundaeDrive

3 жыл бұрын

Glad we were able to help!

This video made my coil/spark plug change a breeze and it saved me a lot of money so far... We'll see how long the coils last. Cylinder 3 was a pain but worked out. Thanks again for the tool and part recommendations. They all worked out great. Thanks again!

@TheSundaeDrive

2 жыл бұрын

Awesome! Glad it helped

@julianalvarado6038

Жыл бұрын

@@TheSundaeDrive does this also work on an 07 camry, its the same v6 i believe

@davecold58

Жыл бұрын

hey quick question. which packs and plugs did you buy and if they were aftermarket how are they holding up?

Thank you very much sir. You confirmed what I suspected on this 2007 Lexus ES350 that I was working on with almost the same codes. Replaced the #6 coil, cleared the codes, relearned the computer, and the six banger purrs like a kitten again. Customer is tickled pink.

@TheSundaeDrive

3 жыл бұрын

Woo!

Excellent video! Thanks for posting this video!I just replaced spark plugs for my 2013 Lexus ES 350 and doing this way instead of removing the intake manifold and throttle body. This way gave me lots of more room to work on the rear three plugs and I didn't have any problem removing the two bolts holding the bracket on top of the rear plug on the passenger side. Thanks again for the video!!!

@TheSundaeDrive

4 жыл бұрын

awesome! I'm glad it helped you

@markg999

2 жыл бұрын

So I'm guessing you removed the windshield wiper tray...he didnt do that step in this video.

Did mine according to your video. Worked out GREAT! Thank you!

Right on man. I'm planning on doing this soon and wasn't looking forward to removing the manifold. Thanks!

@TheSundaeDrive

3 жыл бұрын

No problem! Hope this helps you out

Awesome video. I had everything to do it ,I used a Makita kit that had a swivel in it . I'll be returning my gaskets lol. Video definitely deserves a 👍🏾. Thank you for your time !!

@TheSundaeDrive

3 жыл бұрын

Awesome! Glad it helped you out!

You make it look simple, thanks for the information

@TheSundaeDrive

4 жыл бұрын

It isn't too bad. Hope it helps you out!

I've built up my jeep and switched to Lexus. Thank you so much for this video!! I afraid there wouldn't be as many videos like there is for Jeeps.

@TheSundaeDrive

4 жыл бұрын

No problem! Glad the video was helpful for you

@lichking3711

3 жыл бұрын

well the jeep v6 is easier because it's longitudinally mounted but there is also no way of getting to the sparkplugs without removing the intake. Fortunately, you only need a 10 and 8 mm and about 1.5 hrs to do it.

Thank you, awesome video. Wouldn't have done my plugs without your thorough steps.

@TheSundaeDrive

3 жыл бұрын

Glad it helped you!

Okay...firstly thanks for the video. It was done very well. Nice camera work, great job breaking down all the tools and torque specs. Thanks for linking the tools and parts. Now for my gripe...I did this today on my 2007 es350. No mater what I did I could not get enough slack in the harness to get the number 5 coil pack out. I wasted at least an hour trying to get enough wiggle room to get the coil pack out. It took me like ten minutes to pull the manifold and air box. Once I did that the coil pack was out in five minutes. I wish I had pulled the manifold first and saved an hour. also I recommend putting something over the pinch weld to protect your left forearm when working from the right side. Eventhough I was wearing long sleeves my forearm is pretty torn up.

@TheSundaeDrive

6 ай бұрын

They definitely don't give you a lot of room or slack. Sorry to hear it fought you so bad but glad you were able to get the job done!

Really like the race car sounds in the time lapse! Thank for the video!

Thanks man, just changed my LS460 plugs last month, thought I would have to take off the manifold when I decide to change my ES350 plugs but you just saved me from that. 👍💪

@TheSundaeDrive

4 жыл бұрын

Awesome!

@357wesdog

4 жыл бұрын

Have to do my 15 Sienna and thought the same. Did you just need that swivel spark plug socket like used in his video?

@CJ-ow1cw

4 ай бұрын

Dang baller alert

very well done, step by step in detail. thanks for making & sharing this vid! 👍

Just completed it. I almost gave up on the final plug behind the harness 6 times. Had to get on top of the engine with a really hard pull to get it. It took me an hour just to get to that final tug that release it from the wiring harness. The rest is easy. 225K ES350. Front 3 had oil leaks but these back 3 show no leaks. The cover gaskets in the front had hardened badly so I definitely didn't want to do the work for back valve cover yet. only your video kept me pulling on that wiring harness until gave way because you showed video evidence it could be done. thanks for the detailed video. It did take me much longer than 1 hr because I didn't have that wire clip tool, so I bent something I had into what you showed and those clips finally come right off.

@TheSundaeDrive

Жыл бұрын

Glad you were able to get it! Definitely a bit hard for that one.

Great video with details! Just the project I needed while sheltering at home. Did it on my 2008 ES350 with 121,000 miles yesterday. Took about 4 hours with slow work, checking and re-checking to make sure I didn't forget something. A test drive afterwords felt as smooth as before. Just a few notes to share. (1) All tabs on the connectors to coils were broken to the lightest touch! (Video 5:03). I think the age of the car has something to do with it, but there is no easy way to fix that, so I'll just check them once in a while. (2) #3 plug (the "middle" one) was indeed the hardest to get to. I have to loosen up a bracket (10mm nut) that is right next to it which holds the cable harness. Still, with that extra wiggle room, getting the coil back in was almost impossible! (3) The thread on the removed plugs showed some grease/stain, but nothing serious. Might be from the hardened valve seal, but not urgent. (4) I have to say the "work space" is REALLY tight for those hidden plugs. Anyone with well-built arms probably should re-consider. Overall, thanks for the fun project!

@TheSundaeDrive

3 жыл бұрын

great tips! Thanks for the feedback

The retaining clips are extremely brittle for these cars. If yours breaks off don't worry you can still connect it in. I changed spark plugs last year and my ignition coil connectors have not slipped off or anything. You'll be fine 👍 just make sure it's pressed in all the way.

So professional. Thank you for the video

@TheSundaeDrive

2 жыл бұрын

Hope it helps!

Thank you so much for such a high quality video. Gonna do my 2008 Avalon tomorrow without removing the intake manifold after having watched this video. edit: Just changed out all 6 spark plugs, took 4.5 hours. For your interest, here's a list of all the major hiccups I had with my vehicle: 1. removing the wiper blade arms 2. removing the electrical connection shown at 5:40 due to old plastic 3. clearing out all the coils and wires that's covering the rear plugs 4. removing ignition coil 2 and 3 probably due to the vacuum in the chamber 5. removing ignition coil 3 due to all the crap covering it 6. removing spark plug 3 due to all the crap covering it 7. putting back ignition coil 3 due to all the crap covering it The biggest pain in the f***ing ass is #5. I have no tips or tricks, the whole thing is just a huge fiddle around... not an easy or fun job, in fact it's physically painful. Still think it's worth the work to save $500 + tax at the dealer though.

@TheSundaeDrive

4 жыл бұрын

Not the most fun job for sure. Glad the video helped tho! Thank you for the pointers

@ddcll9538

3 жыл бұрын

@Buddy Boyy It fits?

@vincentfisher4748

2 жыл бұрын

I had to replace the alternator in 2019 on my 07 es not a fun job either. Today a code popped up for number 3 coil again for the third time, this time I'm going to install a new spark plug along with coil.

@pardesi_life

9 ай бұрын

You were able to do it without removing the plenum and throttle body ? I am in a situation like yours. In some videos they remove the cowl and in some videos they don't. And in some videos the remove the plenum. I have a bad number 5 coil.

Thanks enjoyed the video. Now the work begins on my es350

@TheSundaeDrive

2 жыл бұрын

Best of luck with it!

Looking to do this on a 2008 Highlander and thought there was no way around removing the intake. This was a very helpful.

@jackbaccus9866

Жыл бұрын

were you able to do it this way on the highlander

Thank you for the video so helpful and saves me time & money 👍🙏🍻

@TheSundaeDrive

3 жыл бұрын

Glad it helped you!

Thanks for this tutorial. Everything went smoothly thanks to your tips. One of the plastic spouts that connect the vacuum lines to the air box snap at the base and the hose cannot connect. Any tips to fix it?

Great tutorial for the plugs mate

@TheSundaeDrive

3 жыл бұрын

Thanks! Glad it helped!

Good video Good teacher. Patience and smart.

@TheSundaeDrive

Жыл бұрын

We try to do our best! Thank you

Great video with details! Thanks Reply

Nicely produced video, but under an hour is quite challenging considering the rear three.

Spark plug socket set on the way thanks for the video.

@TheSundaeDrive

3 жыл бұрын

No problem!

Just received my NGK iridium spark plugs from Amazon, wish me luck on replacing all coil packs and spark plugs. Decided to do ALL since my ES is at 183k miles and I don't know when anything was done last, and with one coil pack going out, just doing em all... Cross your fingers LOL

@yodead369

3 жыл бұрын

Why do people waste their money on Amazon... RockAuto have the OEM parts you have to pay the shipping but the part price is actually the cheapest place.

@MiguelRPD

3 жыл бұрын

Next time don't use Amazon because the amount of fake items have Increased significantly. Just buy them at AutoZone of Advanced auto part, they sell DENSO oem products. I got mine for around the same price as Amazon.

@monstersofthemidway7125

3 жыл бұрын

Brick N' Mortar all the way for me unless the price is significantly less.

Great video. Thanks.

This is an excellent video! Thanks for posting. Do you happen to have the torque specification to be used when re-attaching the strut brace and the windshield wiper arms? Thanks again!

@richard6802

4 жыл бұрын

Windshield wiper bolt torque=16 ft/lbs

Just finished this job on an '07 ES350; Middle rear coil needed replacement. The video & instructions are good, BUT, if you buy winter gloves marked Large, IMO, this is not the method for you. Large hands - all I was able to accomplish, working in the dark, was tearing up my forearm, while changing the coil & plug on Cylinder #1. Cylinder #3 I found impossible. #5 - Didn't even try. I threw in the towel, and pulled the intake manifold. Suddenly I could see everything, and it was all accessible. Factory method was much easier than I expected, will cost you an additional $30-$40 in new gaskets. One more thing, the OP used a one piece 11-inch spark plug wrench, with swivel and extension. IMHO, **too long**, it got in the way doing the Lexus, but, may be perfect for an RX or Highlander. If you're buying one, suggest slightly shorter 10" length.

@tambayray

2 жыл бұрын

This comment is correct, cylinder #1 and #3 are tough but i was able to do , however #5 is impossible because wire harness is right on top of coil so even if you loosen the coil there is no room to pull it out no matter what wire connections you pull

@FLORIDAERO

2 жыл бұрын

I feel your pain. #3 was out. replaced plugs in 2, 4, 6. piece of Cake, Replacing plug # 3 and coil pack. May call it Quits if she runs well. The engineering on these Lexus. They should be shot. Labor for even a simple alternator is a nightmare.

@MusicConnoisseurian

Жыл бұрын

I didn't even know you could do this without removing the intake. Now i'm wondering if there's room on the Highlander and the next gen ES.

Well done Sir!

Thank you very very very much the tool you recommended for the spark plugs was very helpful. I was looking for a away to do it without removing the air intake and your video did the job 👍.

@hussamalreddadi1157

4 жыл бұрын

My car is 2008 Avalon by the way.

Very well done! I hope novice mechanics seek help from seasoned techs to do this. This task is not easy.

@TheSundaeDrive

6 ай бұрын

Thank you!

Thank you for that information.

@TheSundaeDrive

4 жыл бұрын

No problem! Hope it helps you out!

Very good video, on the back which one is number 6 Toyota 3.3 v6

Great video easy to follow

@TheSundaeDrive

Жыл бұрын

Glad it was helpful!

Love good tutorial videos like this

@TheSundaeDrive

6 ай бұрын

More to come!

Thank you so much! I have replace No.3 coil in my 2007 Lexus ES 350 today. Your video explained every thing in great detail and it directed me perfectly! There is only one minor thing to remind. When we pull the plastic cover under the windshield, we'd pull away first, then pull it up to uninstall it. I mean we should pull the cover away along the windshield direction first because there is a slot at the edge of the cover in which the windshield inserts. I pulled it up directly and the slot damaged the windshield a little. Anyway, thanks again!

@TheSundaeDrive

4 жыл бұрын

Glad it helped and that's a good note! Thank you!

Amazing job

@TheSundaeDrive

4 жыл бұрын

Thanks!

Thank you i did not know it was that simple.🤔

@TheSundaeDrive

5 ай бұрын

glad to help!

Thanks so much for this video- you and car care nut both helped me do this and figure it out ! Unfortunately when trying to get that upper bolt back in it dropped somewhere in the engine not on the ground. I’ll try and fish it with a magnetic tool but if I can’t what is that bolt called or referred to on the upper bracket ? Thanks again

Thank you Sundae Drive! This is the best video on this subject. I just finished the job of replacing all 6 ignition coils and plugs. I had P0351 #1 but #6 that I had replaced a few years ago was cracked (yes, it was a after market brand). I think P0351 can also mean other coils or spark plugs might be bad. The toughest was #5 due to the wire hardness blocking everything. I did follow what you did but there was a separate small wire bundle from the rear wire hardness going towards the intake manifold by #5 that was short so it was still blocking access. I did finally manage to pull out the #5 coil by pulling the wire hardness by hand but I almost gave up. I did not have the right tools so this took me 4-5 hours. I also replaced the front ignition coil wire connector plug since all the clips were broken but not the rear ones so hope they stay put. This is on 2007 Lexus ES350 130K miles with all original coils and spark plugs except #6. I clear the code but have not driven yet so hope this did the job. I ended up doing the job laying on the engine that gave me the best access.

@TheSundaeDrive

2 жыл бұрын

Glad it worked for you man! Hope your issue is resolved!

I was changing my washer fluid and was surprised to see the sensor that connects to the white housing on the left of the plastic intake manifold was disconnected at 5:38. What exactly is that sensor? A clear shot of it is at 6:09

Hello mate, Am from Sydney. I have an RX330 which seems like needs new coil packs and I may do the sparks while at it. I am presuming the process is not to dissimilar to this model in the video. Other issue I have has to deal with for a few years now is white some coming out upon starting especially after long drive. Lately while driving there seem to be a gentle rattle before big puff of smoke. I seem to have spent more money in topping up with expensive-full synthetic oil in this car then any other. It is a good and comfortable car to drive when it is running good as you are probably aware. Anyway I am a novice but I might try and changing the coil and plugs myself as I am not working at the moment and may be able to save some labor cost. Any tips would be greatly appreciated.

Any suggestions on "how to" replace the camshaft position sensor under the air intake? I'm having a really hard time figuring this out

Which one is ignition coil #2 on 2003 Lexus es300?

Great video,

Thank you so much for this video, I am attempting it at this very moment using your video for reference. I do want to note, that my owners manual says the gap is 0.043"/ 1.1mm and do not gap them.. I have found conflicting directions on this so I am going to leave mine ungapped (btw I am using ruthenium spark plugs, what ever that is lol). I will post here if it all goes well or I had to end up gapping them to have my car run smoothly.

@TheSundaeDrive

3 жыл бұрын

Glad the video is helping and best of luck with it!

one of the bet and concise

@TheSundaeDrive

4 жыл бұрын

Hope it helps!

Before starting this job, highly recommend you have ignition coil connectors on hand. Connectors are somewhat aggressive and because of exposure to heat, plastic can be brittle. Chances are one or more connectors will break clips. Easy to unpin old connector and install new one. This is important for the rear bank connectors which cannot be accessed with intake installed.

@TheSundaeDrive

6 ай бұрын

Very good point. We got lucky but always better to be prepared

At 6:06....what is that hose facing right toward palm? Has a hose clamp on it but looks open?

Hey just did mine and on the rear ones that big harness when I pulled on it I ripped the 3 wires that go into the camshaft sensor right below it. There's a yellow, red and black wire but not sure what order they go into the clip, do you by chance know

Great video just bought a 2009 ES350 with 140,000 miles on it now I know what I’m up against but first thing I’m doing is removing the oil filter canister and putting a conversion kit on it so I can use a spin on oil filter don’t like the canister type filter no anti drain back valve

@TheSundaeDrive

2 жыл бұрын

awesome! beat of luck with it!

very helpful tnx

@TheSundaeDrive

3 жыл бұрын

No problem!

This is one of the best helpful video I have seen for replacing sparks plugs. I am wondering if this technique is working for 2010 Toyota Highlander

@TheSundaeDrive

3 жыл бұрын

Glad it is helpful! Haven't done it on a highlander so not sure

@ericdg23

3 жыл бұрын

Same engine 2gr-fe so should be.

hey...what is the mileage of your car? when you did the coil and spark plug replacement

Very nice video. Appreciate all the knowledge. Where did you get your GearWrench set and the torque wrench?

@TheSundaeDrive

2 жыл бұрын

No problem! Amazon, links are in the description.

Also, the effort to reach the rear three, using OEM coil packs are worth the extra cost, IMO

Thanks for this...

@TheSundaeDrive

4 жыл бұрын

No problem! Hope it helps

@TheSundaeDrive

3 жыл бұрын

Hope so!

Great video. If those are iridium spark plugs, I think you aren’t supposed to gap them or check the gap because that scratches off some of the iridium. Haynes manual says it’s unnecessary because they are gapped at the factory.

Very good,I had mine changer the cost was very high wish I would of knowledge this then, I have a Toyota Highlander with 401700 miles on it I keep it in good shape. Do hope to get a few 100K out of it. Thanks

@TheSundaeDrive

3 жыл бұрын

Hopefully this helps you for the next change!

Good video!

@TheSundaeDrive

6 ай бұрын

Glad you enjoyed it

Will this method work on a 2010 Lexus RX 350 ?

I have the 2003 Toyota Avalon XLS with a misfire on #1 cylinder. Was able to replace spark plug and coil without removing anything else. The space is very tight, but doable if your hands are small. Will probably have to replace same on #3 and #5 before too long, so I'm thankful for this video!! But for now, I'm firing on all 6 with minimal down time.

@peytonhoward

Жыл бұрын

How long did this job take you? I got an 06 that has low circuit voltage on coil 1 but it's not misfiring yet

@user-mn6ze7rm2p

Жыл бұрын

@@peytonhoward not long on cylinders 1,2,4-6. Just a min or two to replace, but #3 was a bit difficult, prob an hour.

@peytonhoward

Жыл бұрын

@@user-mn6ze7rm2p good to know. Definitely a little trickier than my truck but that's what YT is for. Thank you!

@user-mn6ze7rm2p

Жыл бұрын

@@peytonhoward if you've got the funds to replace them all, I'd go ahead. I did my one every other month or so..... No money.

@peytonhoward

Жыл бұрын

@@user-mn6ze7rm2p yeah they're really expensive, way more than I thought they'd be unfortunately

Just subscribed....find my answer for error code po353. Hope I could copy and paste your video on my 2009 RX350 !!

@TheSundaeDrive

3 жыл бұрын

Should be pretty similar. Let us know how it goes!

Great video! Did you feel the coil packs snap into place with the spark plug or did you just drop them in there and tighten? Thanks in advance

@Gary_in_NoVA

2 жыл бұрын

They don’t actually “click”; as you say, just drop in & tighten. Not mentioned in the video, but I also add a dab of dialectric grease in the coil tube before dropping onto the plug.

Liked and subscribed... will be using this for my 2013 Camry Se V6 Question though... is it SOP to change out the coil packs when doing spark plugs? I’m at just over 93K miles, and have the OEM plugs and coil packs still in there. Also, I see some KZreadrs applying anti-seize around the threads of the new plugs. Also... would it be necessary to do O2 sensors when doing plugs?

@TheSundaeDrive

3 жыл бұрын

Not necessary to do 02 sensors unless they are bad. At 93K I think your coils are probably still good. If you start having misfires I would change them out but they should last awhile. I'm running original coils on all my vehicles with much higher mileage. I am personally not a fan of antisieze. Newer plugs usually recommend against it. I would verify with the dealer or manufacturer of the plug. Most modern plugs have a coating that protects them. If you do use antisieze make sure it is barely barely any.

GREAT video thanks! Fantastic clear video quality. Would you kindly tell me how the cheap coils lasted? Thanks heaps, Paul

@TheSundaeDrive

2 жыл бұрын

They are still going strong. No issues yet. I'll get an updated mileage count from the owner but seem to be pretty good.

@paulmcbryde9373

2 жыл бұрын

Thanks for the speedy reply. Yes--it would be good to know the mileage before I commit. Thanks again!

i did it thanks

2012 Lexus ES350 -the video is helpful to replace 5 of 6 coils and plugs, however the coil and plug on cylinder #5 are impossible due to the fact that the wire harness sits directly on top of the coil and even if you loosen its not loose enough to pull the coil out. I did 5 of 6 and am hoping for the best. I also noticed the video has the hood taken off, this would save a little back pain if you want to go to the trouble. I did not.

What tool did you use for the strut brace to get the 14mm bolts out? Only part I’m struggling on lol

@TheSundaeDrive

6 ай бұрын

geni.us/MLW2861-22_Impact love this tool, use it for so much

Hello good day I have a 2009 Toyota venza V6 and looks like the same engine cover and the same engine will that be the same process

@TheSundaeDrive

4 жыл бұрын

It will probably be similar. Haven't worked on that particular model tho

I did this same job on my 07 es350. It was hard to reach, but I used the same tools, you just have to wiggle it in there.

@TheSundaeDrive

Жыл бұрын

Glad it worked for you

I would check the torque on the head gasket.

Thanks so much for making this video, I had seen a very detailed breakdown with pictures on one of the Toyota forum websites, but they had you taking the manifold off, after seeing you do this I was also able to successfully do it, and surprisingly it wasn’t nearly as hard as I thought (I had heard it would be a nightmare) the only tough thing for me on my 2009 six cylinder Camry was that I had to lay on the engine a few times to get my head back there and see what was actually going on, but thanks so much for making this video you made the job what I can only assume to be much easier. One crazy thing that I discovered was that I also had a leak on that middle cylinder on the back of the side of the engine, there was oil at the bottom of the coil, I guess that’s a common spot for the valve cover to leak on the 2GFRE engine.? Was wondering if there was anyway to tighten it up while I was back there but I didn’t really see much? If anybody knows a way to tighten those valve covers a little sometimes you can get a little more time out of your valve cover gasket?

@gangcai2876

2 жыл бұрын

No way to tighten those valve covers. You have to change gaskets. It is hard to remove back valve cover for DIY. I could not remove cover and I had to ask a mobile mechanic to my home to remove it.

So good video overall but I took off the windshield wipers and, after reattaching, they are not working. I can hear the motor trying to make them go but they won’t move. Any tips?

@pardesi_life

9 ай бұрын

Did you figure it out.

Thought I saw a NJ inspection sticker on that Lexus. Where you guys at?

@TheSundaeDrive

3 жыл бұрын

South Jersey

Just did this, something I didn't see mentioned in the video: torque the spark plugs to 13 ft-lb. Also 11 inches was too big, 10 inch worked better. And you may as well replace the ignition coil boots while you have the coils out.

@TheSundaeDrive

Жыл бұрын

Thanks! Appreciate that feedback. Good to know that the 10" is better

I like to take off the plenum and throttle body so I can give them a good cleaning and replace hoses with new ones. Also, changing the oxygen sensor while your back there wouldn't hurt. Spark plugs are changed every 100,000 miles so you might as well do it right.

@TheSundaeDrive

4 жыл бұрын

Not a bad plan. Depending on how much you drive, the other parts may be still be good tho as they tend to wear from age and not mileage.

Thanks for the video, it definitely helped. I changed my plugs this last weekend. A few notes for anyone else contemplating this: I had to get a "breaker bar" to remove the strut brace bolts, there was no way they were coming out with my regular socket set. Perhaps the last service place over-tightened these, IDK. The back plugs were a lot more difficult as expected, and for the 3rd one toward the middle I could not get the 11 inch spark plug remover tool to go in the hole (at least the tool I bought which was not the same one he showed). I had a different 5/8" plug socket already and two 4" extensions and was able to do it that way for that plug. It took me about 2 hours to do just the back plugs and re-assmble everything, but as mentioned I ran into some difficulty with the strut bar and far plug removal. Still considered it worthwhile doing myself but be prepared for some difficulty with accessing those plugs and coils especially the third one down in back. I also added a small amount of anti-seize compound to the threads of the plug to make removal of the plug in the future easier and also a compound to the boot so that can be removed more easily as well (I have had two coils go out on my Lexus ES350 2007 and I replaced one with OEM and the other with different aftermarket and the aftermarket boot got 'stuck' on the plug, did not come out with the coil, so adding a boot compound will make removal of that in future easier). Again, appreciate the video, really saved me time figuring some of the earlier steps out.

@bobbyscalchi4013

3 жыл бұрын

I have a 2009 Lexus RX 350 I'm going to attempt in the spring with the plug change i picked it up last June with 167,500 k I'm already at 205k. Forgot to have the dealer give me the maintenance records on final signing. Anyway. Have run into that boot separation seized spark plug dilemma on my other vehicles. I always die electric grease the boots, and anti seize compound the threads on plug changes now as practice. I am not definitely not looking forward to those back 3

@cocoavideos

3 жыл бұрын

@@bobbyscalchi4013 Just pace yourself, it wasn't too difficult but definitely took me more than an hour, I think it was around 2 to do all of the plugs. And getting the right tools to access the plugs. I did put the grease and anti seize on the plugs as well, always a good idea.

@TheSundaeDrive

3 жыл бұрын

You want to be careful using antisieze. It can cause you to over torque and snap the plug. I personally don't use it

My code read po534... which could is bad?🤷🏽‍♂️

Can that obd2 reader give the transmission temperature?

@TheSundaeDrive

4 жыл бұрын

It depends what sensors your car has

Hello, is it possible to do this procedure without removing intake on a 07 Avalon also 2grfe ?

@TheSundaeDrive

3 жыл бұрын

possibly - hopefully someone else here can weigh in

Checking in for an update on those coils 3/20/2021

@TheSundaeDrive

3 жыл бұрын

I'll get an update from him and add it to the pinned comment - I know he is over 144K miles now without an issue

Looking for the link for the ones you bought that have held up

@TheSundaeDrive

2 жыл бұрын

They are linked but here it is again for ya : MAS Set of 6 Ignition Coils for Lexus Lotus Toyota 3.5l V6 Compatible with C1601 UF-487 UF487 C1601 amzn.to/33q4UeQ

I try to go with the factory 🏭 coils because they have the rubber boots at the bottom where as the aftermarket ones are silicone and tear apart when you pull coil out of the spark plug hole.Had to use a pick tool to remove leftover boot material out of spark plug hole.

@TheSundaeDrive

2 жыл бұрын

Good catch! Hadn't noticed that. Oem is always better.

As a professional master technician, I strongly advise against replacing good working genuine toyota coils with cheap coils. Replace only the faulty coil and try to determine the cause of the coil failure. A coil may have failed from a worn spark plug and/or a lean condition on that cylinder. Carbon build up in the combustion chamber could also overwork the coil. If you're concerned about the condition of the remaining coils, have a qualified technician perform current ramp testing to determine whether or not they may fail in the near future. Repair any possible lean condition that may be overworking the coils in addition to the worn spark plugs. Misfires on all cylinders could suggest an overall lean engine condition that will need to be repaired to prevent premature failure of the new coils.

@TheSundaeDrive

4 жыл бұрын

I completely agree. I would have replaced the one with an OEM coil and left the rest. My friend is operating on a tight budget and wanted to replace them all. He purchased them before talking with us and we were just helping him out with the installation. I would never use a cheap alternative for coils but in his case it was all he could afford at the time.

@mikepayne5277

4 жыл бұрын

Had a friend have Lexus replace a bad coil... three times, on a 12 year old car. When they go they tend to go one at a time. Mechanics sure like return customers.

@TheSundaeDrive

4 жыл бұрын

@@mikepayne5277 yeah they do lol. I would only replace what is needed because I can do the work myself. If going to a mechanic replace them all together.

@robertjohnson4401

3 жыл бұрын

@@TheSundaeDrive On a 2007 Avalon with same engine, Coil #2 went bad. I replaced it with an OEM Denso. Now Coil #1 just went bad. That is on the back side. As the procedure calls to remove the intake air plenum, I will replace all three coils at once as I only want to perform the lengthy procedure once. I will see if your procedure without removing the intake works on the same year Avalon. The annoying thing is I had replaced the spark plugs at 108,000 miles and removed the plenum for that job. Now at 124,000 miles, I may have to do it again. I would recommend now to replace the back coils when replacing spark plugs. It looks like these coils have a life expectancy of about 100,000 miles.

@TheSundaeDrive

3 жыл бұрын

That's probably a good plan to do while you are in there. Let us know if this method works for your car as well!

Will this work on 09 Toyota Camry v6 basically the same setup

@TheSundaeDrive

3 жыл бұрын

Not positive but it should be similar! Maybe someone else can weigh in here that has done it.

I have a 2011 es350 with 105k. About to change the plugs. You think I should change the coil packs also? How many miles until they should be replaced?

@TheSundaeDrive

Жыл бұрын

Probably a good time to swap them out.

I'm waiting on parts for 15 Sienna. Anyone know if I can change plugs without removing the intake? All the other vids state it needs to come off. I'm changing struts as well so that wiper crowl is coming off anyway.

@markg999

3 жыл бұрын

I've seen a few you dont..when I had Rav4 I did. Not having to remove it seems possible easier.

Which one is ignition coil#2?

@TheSundaeDrive

4 жыл бұрын

Ignition coil 2 is the front left most coil looking at the engine from the front of the car

I'm wondering if these cheap coils are still working fine and if so how many miles or kilometres on them?

@TheSundaeDrive

4 жыл бұрын

See the first pinned comment for current mileage :) still working well!