Dear sir i found your video very informative ....keep it up

In India we mostly use bitumen based roads, and in this we take bitumen density as 1040 kg/m3, please explain difference between density's of asphalt & bitumen...kindly reply sir

Please sir, can you say, how many stone chips, sand, bitumen used in your estimate quantity....????

Great Informative video

tnx my dear it was very useful

sir please give derivation from where you taken asphalt density as 2330 kg/m3 ....reply soon

Asphalt Density commonly used between 2250 kg/m3 (140 lb/ft3) and/ 2350 kg/m3 (147 lb/ft3) if u have availble component mix Density then use that density if not then its standaard value mostly !!

@haroonali.6081

6 жыл бұрын

Sahil Khan yes sir you are right.

@vikrantbirje159

4 жыл бұрын

Sir than standard value is what? What we have to take

@whodareswins5960

3 жыл бұрын

How to calculate unit weight of Asphalt?

One mistake is there..the quantity u find is in conpacted..but in site material is coming in loose..so u have to add loose material also..

@jonathanbelandres6754

10 ай бұрын

the density of asphalt used is from the laboratory compaction molded "Marshall Method" NOT the loose mix asphalt and tested for specific gravity

Super and very helpful

You Neglected Compaction activity. After Compaction 15 cm thickness become 10 cm. You Neglected specing between aggregate.

@kotivadlamudi5798

4 жыл бұрын

How would we get compaction coefficient?

@CADventureCraft

3 жыл бұрын

@@kotivadlamudi5798 Search 'asphalt fluff factor'

Hello great video and great descriptions. Would you mind inserting subtitles as I struggle with the accent, thank you in advance

Good explanation ji...

Dear sir very good job

Great job

thank you sir

Good lesson

Good job

Good practice

Of which layer you're calculating for ?

thanks

I have few questions sir here I am confuse because we can say that cu.m which object have diff3rent dimensions and m3 those object have same dimension so here we have in this object different dimension now I think we will put cu.m unit for this case I need your response

@jollyjoker1468

6 жыл бұрын

cum (cubic meters) and m3 ,both are same, use can use any of them anywhere

greattt vediooooo sir

How about figure out intersections, curves/ bends

Very good explane

Length x width x thickness x 2.4 = tonnage..a simple way to measure tarmac (2000×8×.15×2.4=57.6 t)

@praveenutagi419

2 жыл бұрын

What is 2.4 value sir?

@djdipucreation3222

2 жыл бұрын

@@praveenutagi419 density of Asphalt

Hi, I need to calculate the quantity (in tons) of aggregate needed to construct 1km of road. The width of the road is 12 meters. Kindly help please.

make video how to design cantilever..jogging and sagging..deflection check..slender and slenderness column, buckling of column

Asalamoalikom how many Letters MC-70 Can use for Same Road

Rcc road ni mapani road na center thi thay?

ماشاءاللہ

Great....

sir dbm aur bc ke density same hoti Hai Kya

Sir density vary krti hai ya fir standard rhti h

please show how to watch drawing detail

Sir plz explain IPC Bill preparation in detail

सर कोटेशन मैं रेट कोट करना और सिखा दो किसी रोड का रेट कैसे मटेरियल के हिसाब से रेट कैसे डिफरेंट करें

Shami sir please upload a building materials estimation & cost

Nice 👍

Thanks couldn’t remember

please make a vide on BBS of circular tank.

sir plzz make one video on BBS of Raft footing

plz make videos on steel structure design

Did you really need to use your calculator to divide by 1000? Just saying Thanks by the way

@kenlau8585

4 жыл бұрын

Smart ass

How much area covers 100 feet road

Good brother

Bhai kitne % damar k liye nikale ho vo to batao

is the density stay the same even after compaction? because I see you use the density of the mixture to calculate the weight of the constructed road. Hope I get an answer..

@Emadaldeen100

2 жыл бұрын

Can someone answer my question please??

@jonathanbelandres6754

10 ай бұрын

@@Emadaldeen100 the density of asphalt use in the computation is from the laboratory test results "Laboratory Compaction" molded using Marshall Method. The laboratory compacted samples are tested in the Lab to determine its specific gravity which he is using in the computation.

Please sir define 2330 kg/m³

Good 8

Sir Asalam o alkum sir kindly upload videos prime coat test and tack coat test for bituminous

@CivilEngineerss

7 жыл бұрын

Ok bro

make video how to design cantilever..hogging and sagging

from where you find this density

good mor.... sir very good video for Asphalt Quantity but sir im asking for (concrete road how calculate quantity

@atifriaz4804

6 жыл бұрын

It's to much simple

#densityofasphalt #volumeofroadsurface

What' is ratio of this concrete

Sir explain how you take asphalt density as 2330kg/m3....reply soon

@udaysinghrajput188

7 жыл бұрын

यस सर मुझे भी

@engrfayyazkhan4777

6 жыл бұрын

Also I can multiply by 2.45 the unite will convert into TON

@maheshhiwale2752

5 жыл бұрын

The Denisty is 2.33 Gm/cc, So multiple it by 1000 you we'll get the density in KG/M3

This video is not for Road , in wearing course bitumen is used with coarse aggregates ...

Super elevation provide in the road ... please tell briefly

How can we get the density it's not explained in video

How density of asphalt 2330

I'm missing something small at the end, why is it divided by 1,000lbs when a ton is 2,000lbs? Thank you for the video!!!

@ruelitostvreloaded

5 жыл бұрын

1 ton is equal to 1000kg

@cctvwelland626

4 жыл бұрын

1 metric tonne is 1000kg (2200lbs (1kg = 2.2lbs)) a short ton or 'American ton' as us Canadians know it is 2000lbs.

@DCclan1

3 жыл бұрын

@@ruelitostvreloaded A metric tonne, has two nn's and an e. A ton is not a metric unit.

Give one example which explains clearly what is running feet???

Dear engineer I need some help from you in civil 3d if you are agree

Well for 2400 sq.m area for 150 mm it requires 839 tonns.

Can you please show us how to compute TACK COAT!

@jonathanbelandres6754

10 ай бұрын

Find the Area to be applied by Tack Coat then multiply by the rate of application (Specs)

How can find the tar and aggregate quanity.

@cctvwelland626

4 жыл бұрын

you can request a mix design from your asphalt provider which will break down the amount or percentages of aggregate and bituminous materials

You compute hot mix quantity only not asphalt, because hot mix contains 2.36,6.25,12.5,20 mm and bitumen. So it's not quantity of bitumen

how to calculate asphalt quantity with different elevation ????

how to get density of asphalt 2330

Any coefficient for dry , wet and materials compaction.

how to calculate labour productivity in construction

How to get the density of asphalt?

please parts of road T.S.T Quaninty

please make a video in rupees calculation estimate

@CivilEngineerss

7 жыл бұрын

Hahaha ok bro

@rhueldemegillo2888

5 жыл бұрын

Density of Asphalt normally is 2.40 ton/cu. m. If you want to determine how much tonne of asphalt. Use 5% by weight.

asphalt mix design

If the measurement in FPS system then

#harbourexpansion

lenght * breadth* height is called volume.

Simple formula (Area * Thickness * Density) Area(8*2000m=1600m) Thickness (0.015cm) Dencity(2330) so 1600*0.015*2330=55.92Ton of Asphalt

@apnat.vpanjab6705

2 жыл бұрын

👍🏼

@Emadaldeen100

2 жыл бұрын

The density is not the same before and after compaction right? Why did he use the density of loose asphalt when he multiplied it by the volume of compacted asphalt??

1qm 2.40 tons

thickness 0.150?

@williamnicoll5719

2 жыл бұрын

6

Please speak hindi.....

And feet my?

S falt = Asphalt. Your welcome.

Cant understand buddy.

its wrong ,didect aggrigate volume

Call it Asphaltic Concrete not Asphalt

Bhai Hindi bolo pata hai aapko English bahut Aati Hai apni Matra bhasha mat bhuliye

@hazratessa2569

5 жыл бұрын

matra basha is pashto you know pashto

Do not trust these KZreadrs ls lab tested dencity changes with the sample of different area. Calculator yes in divide for 1000

make video how to design cantilever..jogging and sagging..deflection check..slender and slenderness column, buckling of column

thanks