How to build a tracked robot | Ardurover Build part 1
Sharing my build on an amateur version of tracked autonomous robots. This is part 1 which is the tracked platform build.
Жүктеу.....
Пікірлер: 39
@Cosmojourney10 ай бұрын
Great project. Thanks for sharing!
@LyndonsWorkshop
10 ай бұрын
Thank you Andrii. And thank you for watching.
@SvenPHX5 ай бұрын
Good stuff, learned a lot. Thank you.
@Erosgenuino17 күн бұрын
Gran trabajo.
@punachaaАй бұрын
thank you. this is exactly my thought also and I already stepped into making similar one. but using Wheelchair motors. and metal welded frame instead.
@PhG19618 ай бұрын
Great ingenuity!
@LyndonsWorkshop
8 ай бұрын
Thank you Sir
@notquitepinoy7 ай бұрын
Awesome design, I like the design of your track tensioner I am going to steal it for the redesign of my first tracked vehicle.
@LyndonsWorkshop
7 ай бұрын
Thank you notquitepinoy. And thank you for watching.
@GutusNirwanto8 күн бұрын
Amazing
@zoeyzhang9866 Жыл бұрын
Nice build!
@LyndonsWorkshop
Жыл бұрын
Thank you sir
@AlanGrubb7 ай бұрын
Great job!
@LyndonsWorkshop
7 ай бұрын
Thank you.
@brucehanson41479 ай бұрын
You have some good ideas there
@LyndonsWorkshop
9 ай бұрын
Thank you Bruce.
@cubix78855 ай бұрын
Pls provide link for motor driver used
@dwightm35946 ай бұрын
Really great build, thank you for sharing. I can't say for sure but it looks like your wheel hubs have a 1/2" bore but the motor shaft is 3/8"? Did you print an adapter sleeve to fill the gap or did you use a bushing adapter of some sort? I am planning on printing an adapter out of PLA and am just curious if you took the same approach and if it worked for you. Thanks again, looks like a really great project.
@LyndonsWorkshop
6 ай бұрын
Hi. Thank you. Yes, I used a steel spacer bought at the local hardware store (Lowes) and used it as an adapter sleeve. If you look closely at the hub you will see that spacer. Your approach of 3d printing it would also work.
@nevillecreativitymentor8 күн бұрын
NOICE 💪❤
@lawrencehuang69348 ай бұрын
😂thanks for more ideas 💡 Now I’m learning everyone ideas of how to build robotics I too just built a prototype But wanted to get better at it 🤣 I hope 🤞 mine will go crazy 😜😈 insane
@LyndonsWorkshop
8 ай бұрын
Your welcome. And welcome to the community of robotics.
@AkwaRevTech27 күн бұрын
Nice work, very impressive. Please can you share the 3d printed files?
@sed18192 ай бұрын
Which motor driver boards are you using?
@kramerdou41312 ай бұрын
How much did it cost to build the robot? Roughly?
@lawrencehuang69348 ай бұрын
Question 🙋♂️ how many LBS is that robot weighing at ?? Trying to choose plywood or steel framing with aluminum covering.
@LyndonsWorkshop
8 ай бұрын
18lbs.
@lawrencehuang6934
8 ай бұрын
Ty
@brandonwinstead88679 ай бұрын
Will you share the print files?
@LyndonsWorkshop
9 ай бұрын
Sure. Provide me an email to send it to.
@hitmanevo73899 ай бұрын
wht type of esc did u use
@prathamdeepsingh8210
8 ай бұрын
Those are motor drivers not esc
@sed1819
2 ай бұрын
What model of motor driver? @@prathamdeepsingh8210
@prathamdeepsingh8210
2 ай бұрын
@@sed1819 probably about 10-15a brushed motor drivers
@truonggiangnguyen29699 ай бұрын
can you please share the names of those components? thanks very much!
@LyndonsWorkshop
9 ай бұрын
Hi, are you referring to the electronics?
@amosto7862
7 ай бұрын
Hi @@LyndonsWorkshop, I'm also curious about the electronics. Could you share the name of the motor drivers you use? Thanks!
@LyndonsWorkshop
7 ай бұрын
@@amosto7862 Hi, its SyRen 10A motor controller. You could go for higher Amperage. You could also go for sabertooth motor controllers.
Пікірлер: 39
Great project. Thanks for sharing!
@LyndonsWorkshop
10 ай бұрын
Thank you Andrii. And thank you for watching.
Good stuff, learned a lot. Thank you.
Gran trabajo.
thank you. this is exactly my thought also and I already stepped into making similar one. but using Wheelchair motors. and metal welded frame instead.
Great ingenuity!
@LyndonsWorkshop
8 ай бұрын
Thank you Sir
Awesome design, I like the design of your track tensioner I am going to steal it for the redesign of my first tracked vehicle.
@LyndonsWorkshop
7 ай бұрын
Thank you notquitepinoy. And thank you for watching.
Amazing
Nice build!
@LyndonsWorkshop
Жыл бұрын
Thank you sir
Great job!
@LyndonsWorkshop
7 ай бұрын
Thank you.
You have some good ideas there
@LyndonsWorkshop
9 ай бұрын
Thank you Bruce.
Pls provide link for motor driver used
Really great build, thank you for sharing. I can't say for sure but it looks like your wheel hubs have a 1/2" bore but the motor shaft is 3/8"? Did you print an adapter sleeve to fill the gap or did you use a bushing adapter of some sort? I am planning on printing an adapter out of PLA and am just curious if you took the same approach and if it worked for you. Thanks again, looks like a really great project.
@LyndonsWorkshop
6 ай бұрын
Hi. Thank you. Yes, I used a steel spacer bought at the local hardware store (Lowes) and used it as an adapter sleeve. If you look closely at the hub you will see that spacer. Your approach of 3d printing it would also work.
NOICE 💪❤
😂thanks for more ideas 💡 Now I’m learning everyone ideas of how to build robotics I too just built a prototype But wanted to get better at it 🤣 I hope 🤞 mine will go crazy 😜😈 insane
@LyndonsWorkshop
8 ай бұрын
Your welcome. And welcome to the community of robotics.
Nice work, very impressive. Please can you share the 3d printed files?
Which motor driver boards are you using?
How much did it cost to build the robot? Roughly?
Question 🙋♂️ how many LBS is that robot weighing at ?? Trying to choose plywood or steel framing with aluminum covering.
@LyndonsWorkshop
8 ай бұрын
18lbs.
@lawrencehuang6934
8 ай бұрын
Ty
Will you share the print files?
@LyndonsWorkshop
9 ай бұрын
Sure. Provide me an email to send it to.
wht type of esc did u use
@prathamdeepsingh8210
8 ай бұрын
Those are motor drivers not esc
@sed1819
2 ай бұрын
What model of motor driver? @@prathamdeepsingh8210
@prathamdeepsingh8210
2 ай бұрын
@@sed1819 probably about 10-15a brushed motor drivers
can you please share the names of those components? thanks very much!
@LyndonsWorkshop
9 ай бұрын
Hi, are you referring to the electronics?
@amosto7862
7 ай бұрын
Hi @@LyndonsWorkshop, I'm also curious about the electronics. Could you share the name of the motor drivers you use? Thanks!
@LyndonsWorkshop
7 ай бұрын
@@amosto7862 Hi, its SyRen 10A motor controller. You could go for higher Amperage. You could also go for sabertooth motor controllers.
@amosto7862
6 ай бұрын
@@LyndonsWorkshop Thanks! I'll look into those