If your car has negative switched headlights, (Most Japanese cars from early 2000's) follow this guide guys! He does a really good job of explaining everything clearly and explains every part of the way. This is cheaper and better than any of the adapter harness's, which are really hard to find/determine which specific one you need for your car. I did this for a 2010 honda fit and most other Hondas from early 2000's would be the same. There's a comment in here about reducing the output slightly because of the diodes, I can say that I did notice it too but because the lights are so much better and brighter than the stock halogens it didn't matter to me. (Edit) Honda fits are positive switched headlights and this process will work fine you will just have to switch the orientation of the diodes.

@bulgarianicedtea7897

2 ай бұрын

Another tip guys, keep your soldering iron hot and be as quick as you can with the diodes, these seem to bee extremely sturdy/ heavy duty but I have heard from other enthusiasts that they have ruined a couple of diodes by overheating them when soldering.

@kesipi4465

Ай бұрын

what led you use? i have h1 sized projector, and i wanna do my fit to

Thanks, this is thw video that I needed. I thought about using diodes but didn't know which ones to use.

ive been messing around with my 2nd gen crv for 2 weeks now. this was the fix i needed. thanks so much 🖤🖤

I like to instead add a relay kit to change from switched ground to switched positive. Use the wires from your original plugs high and low to activate the relay and give you full power straight from your battery. Plus it takes all the load off your factory switch

Great info, ordered from your Amazon link. For HIDs you could probably run those diodes if you're powering ballasts with a relay harness, just wire them to the relay coil circuit

@NextLevelNeo

5 ай бұрын

Theoretically yes. HIDs are usually only 35watt, maybe 50. The biggest concern i would have with HID is that initial surge of power to ignite the bulbs. You can try, worst case youll fry some components, maybe the diodes, but they are beefy diodes so they should be able to take it.

@ed4647

5 ай бұрын

@@NextLevelNeo oh I wouldn't wire the diodes to ballast power. I'm talking about connecting diodes to the OEM low and high + leads like what's done with the LED projectors, but they'll be connected to the "trigger" circuit of the relay. Very low current is needed to power those circuits.

@NextLevelNeo

5 ай бұрын

@ed4647 oh, so still using a relay, yea that would be totally fine

Hi there, very good video. I have a situation. I bought Sanvi biled laser projectors 3". The projector has 5 wires, 2+ and 2-, for the low and high beams. I guess the fifth wire (yellow) is for the laser, but, when I join that one with the high beams, the projector turns off and restart. I am testing the projectors with a 14v laptop adapter, could it be the reason of not getting the laser beam? Or does the wire need diode? The projectors uses canbus because of my car (Hyundai Elantra i35 2013). But, another situation is, when a I connect the canbus, nothing work even the projector, and when I connect laptop adapter directly I can see the low beam and the hight beam, less the laser because of the fifth wire. Any guidance or information will be welcome, thank in advance.

I tryed that on a car that has projector low beam and a reflector high beam. When i installed bi led projector high beam works only if low beam is on so i used 10A10 diode so the high beam can work when low beam is off but diode is getting VERY hot.

@NextLevelNeo

19 күн бұрын

On most cars like that the low beam stays on when the high beam is on and you won't need to use this style harness. What car is it?

Ill hire you to help walk me through wiring my led projectors.

so are the diodes so you don't ground both hi and low? could you omit the diodes if you want to run both hi/low at the same time all the time? i mean wouldn't the shutter do its job as far as not blinding people when in low beam? also i hear a 3d printer in the back

@NextLevelNeo

5 ай бұрын

The diodes are a one way circuit. they prevent the signal from back feeding. If you want both hi and low all the time then you could just connect both high and low ground together. Without the diodes its just a basic power ground circuit, but this would open the shutter anytime the low beam is on, so you would be blinding people with the high beam anytime the projectors are on. You also need to consider each car varies. Some use ground switches some power. You will have to adjust the diode orientation and wire layout accordingly.

Make a video like this for the 9007. I have an Srt-4 so that would be very useful for me. Thanks

@NextLevelNeo

7 ай бұрын

The process is the same you just need to find a pinout for the 9007 to determine which pins do what. Even with a 9007 not all cars are the same.

@NextLevelNeo

7 ай бұрын

kzread.info/dash/bejne/apqM2JiuipXcYZM.html&si=5Q7kLI6nyQ2uTiFS

@jasonhughes9720

7 ай бұрын

That was the first video of yours I watched. Very informative. Thank you for making the video on it bc all others were videos after the Install was already done. How can I get in touch with you?

@NextLevelNeo

7 ай бұрын

@jasonhughes9720 best way to contact us is through socials. There are links on our website www.nextlevelneo.com

How different of a hookup is it if the system has power switches?

@NextLevelNeo

Ай бұрын

You just flip the diodes 180 degrees

do you happen to make a harness for an 04 Honda Element using Gzminjie 3" ? It has a red, Black along with smaller white and yellow wires.... HELP!

@NextLevelNeo

3 ай бұрын

We don't make harnesses but you can follow this guide to make your own.

@danmccarthy5247

2 ай бұрын

great video although still unclear which wires go where on the 3 prong plug?? TY Dan@@NextLevelNeo

@NextLevelNeo

2 ай бұрын

@@danmccarthy5247 that's because there are many different variations. You have to figure out what layout your car has. This is why we don't just make a harness and sell it. There are too many variations.

@danmccarthy5247

2 ай бұрын

I understand thanks for the interesting video!!@@NextLevelNeo

Using diodes is a simple and economical solution to power the low beam when the high beam is turned on, but I don't recommend it since it decays the power of the projector slightly, or in my case of using a biled low beam 70w the decay of intensity is too noticeable, I had to repeat all the wiring again and add a relay that positively feeds the low light with 70w. Generally positive battery

@luisangelmancilla4601

8 күн бұрын

where did you add the relay?

@madoasful

6 күн бұрын

@@luisangelmancilla4601 If your vehicle or motorcycle uses normal polarity (two positives and one negative), 85 and 86 would be negative and signal high light, 30 is low light projector and 87a is signal low beam, thus the relay comes (NC) permanently bonded 30 with 87A without the relay being active and thus gives you low beam, to pin 87 you connect high beam signal (85 or 86) making a bridge, high beam of the projector and that's it, when the relay is activated, it will activate high beam and through pin 30 it will power the low light of the projector, so you will not have to use diodes that cause voltage drop.

No load resistors needed? I have an 03 ram and was told load resistors are needed to power the high beam.

@NextLevelNeo

6 ай бұрын

On some cars you may need a canbus resistor. That will stimulate the load of a halogen bulb, if the car looks for that load and doesn't see it it may trigger a dash light or in some cases the lights won't work without it. I don't belive the 03 ram has that though, but i could be wrong. Either way that is separate from this harness.

@patron1839

6 ай бұрын

Thank you. Yes my Ram requires it

Does this circuit harm the projector or any kind of an other issue?

@NextLevelNeo

2 ай бұрын

If done properly, no, it will not harm the projector or the car.

@thehornstore2755

2 ай бұрын

Do we need to put a relay or something for safety or this works fine without relay too ?

@NextLevelNeo

2 ай бұрын

Generally no relay is necessary. But it would depend on the factory wiring gauge and wattage load of the projectors.

@thehornstore2755

2 ай бұрын

@@NextLevelNeo okkk thanks

Can i used a 6A diode

@NextLevelNeo

3 ай бұрын

I use 30a diodes, using smaller ones may be result in a failure. here is a link to the parts i have been using for years with good results. amzn.to/3D2UGFc

@arnoldrapthap7306

3 ай бұрын

Can i use r5000f.. as for my location the link you send is noy available to purchase it.

The number or amp of schotty diode

@NextLevelNeo

3 ай бұрын

You can find a link to all the parts needed in the video description. Here is the link amzn.to/3D2UGFc