I'm trying to figure out how to lift my car and now my parents think I'm watching a 80s porn video

@JohnWRathwell

5 жыл бұрын

😂

@rkgsd

4 жыл бұрын

Evidently your parents watched 80's porn. Why else would they think that's what you were watching?

@cjakabigbank2932

4 жыл бұрын

Lol

@summerwinter2864

4 жыл бұрын

boosted kid productions 😂😂😂😃😃

@jstasze

4 жыл бұрын

@@rkgsd who HASN'T watch 80's porn?

Wow! I've been searching for 2 weeks on how to do a quick fix in lifting the passenger side of my car. My tires on that side keeps getting shredded by the hull. You are my hero!

I used these on my 98 park avenue...when the air shocks went out. Keeps the rear end of the car from sagging...but the ride is stiff. Also you wanna be careful on train tracks and pot holes, because they tend to shift if not secured at the bottom. They also work in reverse to lower the car.

@simsatvrepair1255

2 ай бұрын

It’s stiff cause the shocks aren’t doing anything that’s your second support system airshocks don’t cost that much

use hose clamps on each side of the spring next up to touching the expander so it doesn't shift around.

I got a 1997 Mercury Grand Marquis & I want to raise my front end by 2 inches. Nice informative video.

Thanks,and the music was a nice touch!

My son asked me just what the hell I was looking at, when it dawned on me on just how much it does sound like a porno.

@gladiator_games

5 жыл бұрын

LOL

@Hifromthechi

3 жыл бұрын

Lmfao I'm on the porch in front of my house and had to put down volume quick lol neighbors were giving me the eye 👀🤣

@MonkeyBizness420

3 жыл бұрын

Pinche jalisco

@shannondoyle4845

3 жыл бұрын

😅

Welding the seats to the spring is the safest. Great idea, thank you

I've had my Corolla professional for a decade its a good vehicle the problem comes when i drive in the gravel road and on dirt road and also over speed humps it is too low and it damages the belly of the car. Luckily I heard of these spacers and installed them. The car now has a good ground clearance although it looks a little abnormal but since i stay in an undeveloped place and its for my daily use to and from work, i must say i can go over anything with ease they saved me a ton of stress

I have '94 Buick Park Ave with self leveling which crapped out and my rear end went south so I resorted to this to raise it

Good video ,i was replacing a shock and i think i compressed the spring too much ( i used some clamps ) i guess to add the height it had back on is just like you have in the vieo?

I had these on all four corners of my07 Malibu to increase ride height. They worked wonders. Did actually change the ride quality for the better. I put new quick struts all the way around ( sorry the 07 sedan has shocks on the rear ) first then did this. I'm about ready to do this with my 08 Buick Lacrosse due to how bad it squats with my boat hooked up. They will only be on during the fishing season. I'll be upgrading the sway bar bushings and end links plus throwing a new set of struts on the back end. No thank you to the roads here in Michigan. Best placement is in the middle to upper coils of the spring.

@davidwagner956

5 жыл бұрын

dude your ass roll around on a 87 Huffy with a 16" rim on the back and a 10" rim in front with a fucken banana seat!

@TheInternalwisdom

4 жыл бұрын

Bobg Gallagher thank u! I too have a boat that makes the back of my SUV sag alot even with a weight distribution system that im using.. so plan on putting in some spacers and these as well.. also nice to have a lift on the back due to lowered clearance by the towing hitch sticking out and down2-3 inches..

@bobg69

4 жыл бұрын

@@TheInternalwisdom your welcome. Had to get another vehicle due to a uninsured kid on learner's permit. Totaled out the Buick. My town rig is a Trailblazer. Minimal squat with the boat. Looking into getting it leveled out/lifted. 2 inch in front and only 3/4 in the rear. It will take a 31 inch tire without wheel spacers due to upper ball joint clearance. GM's forward rake is good for fuel economy but hurts the ground clearance. I'm going to slap some on the front for now so I can get back to deer camp without scrubbing the front bumper cover.

how did these work and do the wheels track straight?

I found out it will wear out front struts within a year , I did install spacers on rear coil springs . But these were perfect on my 1972 Monte Carlo .

I've got a set of shocks and springs. It's a 2 inch lift for a Nav. I'm gonna try to use them. Maybe put the Caddy tophat on the nav shocks. It should work. If not I'll use the springs

If they can come with the idea of having a way of putting a supported to raise the hight evenly in the center springs. . it just might be better and will support like a strong spring. .and ride smoothly. ..

might do this for my 02 corolla

Dude that is a great idea ! adjustable too. Might need to use 2 or 3 and weld to the spring for longevity but great idea.

@kikispeed4

2 жыл бұрын

Weld? U won’t pass inspection

@0.pgamng

2 жыл бұрын

@@kikispeed4 they wont see it unless u go to a serious shop that’s serious all the time😂

These are the best way to compress your springs to get the rubber ones off...so you can use it as a tool or a spring lifter...simple but smart engineering

I've raised sedans like 1978 monte carlo and 1988 classic caprice front about 2 1/2 and rear I've done 4" by changing the bolts, got the bumper from my knee up to half of thigh... freaking thing looked like a car/pick up truck, one thing you need to try remediate is the issue that they rotate, so you always want to go on the bottom of the coil not the middle...

You can also use these as spring compressors by flipping the metal pieces.

This is the same as putting a wood wedge between the coils. IT ESSENTIALLY SHORTENS THE SPRING LENGTH, FORCING THE SUSPENSION TO BOTTOM OUT SOONER. IT STOPS THE COILS FROM COMPRESSING TOTALLY.

Great Lift kit alternative if you do the gambler 🤘🤘

@kstew9034

3 жыл бұрын

ABG!! 🍻

Great quick diy vid. Straight to the point. Wondering how they ended up performing for you, and if you had any problems?

@JohnWRathwell

2 жыл бұрын

These aren't meant to be permanent. To prevent them from sliding around the coil, plastic ties should hold them in place.

Ive done all my chevys like this. About to lift my 2000 park ave right now

@jdudsentertainmenttv6595

2 жыл бұрын

So you didn’t have to bend your shock plate ? I have an alero Oldsmobile two door coupe tryin to fit 22’s it’s meeting my shock plate so my rims won’t go all the way on I have lifters I’m just not sure if they will work it’s my first time putting rims on a car

Funky track man!

Nice job 👏👏👏👏👏👍👍👍👌👌👌

So what are those called and where did you get them? Thanks

About to do this on a 1999 Mercedes Benz clk 320 my wheels rub against the body of the car so I’m giving it a little boost

I would not recommend this. I did it on my Jeep, loved the level same as the rear. But it did take a while to get these on, so I started wondering if it's worth it. I could have bought new springs and installed them. But, what's done is done. So, the next day I got as far as the end of my driveway. One spring snapped. I just ordered new springs.

I used these once in late 90s, a mechanic told me to be careful, they could break them springs.

@goreobsessed2308

3 жыл бұрын

You really want two on both springs set to nearly the same height if you rock just one it puts more stress on the other side and can cause problems

@bobbrown2312

Жыл бұрын

These are old school now ,as far as I know you can't buy these anywhere anymore.

@JohnWRathwell

Жыл бұрын

Amazon sells them.

@bobbrown2312

Жыл бұрын

@@JohnWRathwell Amazon advertises them but the company that made them has discontinued them a couple of years ago.

@el8233

Жыл бұрын

@@bobbrown2312 they sell them at auto zone

I'd like to speak to you more about this product, I'm very interested.

I'm looking to doing this to my 2010 lincoln town car just to keep the original height of my vehicle when I have a heavy load with out my rear dropping down.

@TownCar512

8 ай бұрын

how did it turn out? did you ever do it?

@frankieguevara9807

8 ай бұрын

@@TownCar512 I didn't get a chance to

I may just try this.

70's porn music

@TheLatinlover9574

6 жыл бұрын

DEMONlCO 😂😂😂😂

@alejandrob-c2277

3 жыл бұрын

🙂

@DeeWadeSoundz

3 жыл бұрын

Right

Is this the way to install if mounting 22s to keep from rubbing plate?

Love the music 👍🏾

Just one pack witch is 2 for one spring can get you 1 to 1 and a half inches. But they require maintenance cause they tend to move around and end up next to each other over time. But they do work.

@Bubbasawyer1974

7 жыл бұрын

they wont move if you tack weld them in place

@codynelson2384

7 жыл бұрын

Bubba Sawyer tack weld them to the spring?

@Bubbasawyer1974

7 жыл бұрын

Cody Nelson that's what I'd do

@BodyWeakDotNet

5 жыл бұрын

Just use small hose clamps, tighten a clamp down on each side of the spring to stop them from sliding...Trust me they will not move at all..

@TheInternalwisdom

4 жыл бұрын

#BodyWeakDotNet great idea! Thank you!

Use locktight and zip ties so they will not move or become loose

@zcruddie1

3 жыл бұрын

Please provide pics or video of how zip ties are used. Thanks

@JohnWRathwell

3 жыл бұрын

You just tie the spring boosters down to the bottom and top to the coil spring.

Getting rubber versions is better these slip round the spring to the same side and bend the spring or shear it in half in certain situations.

This works if rims are hitting the struts

is that good useing the spaces

Underground rim Kings

can these go in the front or back of a vehicle

I was hoping for a video on resetting so I don't have to buy new springs after they sag rather than this. This not really a solution. The question is really, can springs be stretched back to original tension in a safe sensible way?

Great keep exploring

Love the music who s it ?

All right I have a dodge grand caravan 2010 and the back end is low and my muffler is hiting on the piece of metal that is in between that and the gas tank will it raise it up enough so that it doesn't hit against it and make a banging sound

@JohnWRathwell

5 жыл бұрын

It usually lifts 1" to 1 1/2".

So would these (raising the springs) also raise the control arm bolt to prevent from touching the tires on bigger rims (looking to install 26 inch rims)?

@JohnWRathwell

Жыл бұрын

The lifters only lift 1" to 2". The main thing they do is stiffen the ride so you don't get bottoming out of the coils. If you measured the fender clearance for 16" wheels, you should have at least 2" clearance at the top of tire. The control arms won't move more that 1/2" to 1".

These got rid of my saggy ass syndrome on my Subaru, I use them to stiffen up the rear on my other outbacks for more weight better towing too.

how many inches of lift you get? Do they get lose and make noise or rattle? You ever need to adjust them?

@dontadrea7557

3 жыл бұрын

How high u got yours?

@JohnWRathwell

3 жыл бұрын

It lift 1 to 2 inches.

Does this lift the car up and inch?

If you are going to do it do it right

@zackstedelin3096

Жыл бұрын

Nah this looks cheaper 😅

my package told me to set those up a diff way and to set one up on the bottom set of the spring and another one 2 counts up on the opposite side but you can put more than 2 on 1 spring

@JohnWRathwell

6 жыл бұрын

I've heard of people putting 6 lifters in a coil spring. The instructions on my package said to put them half way around in the same coil space.

@black7966

4 жыл бұрын

How long did it last?

I'm asking but if you bought new springs that was bigger wouldn't that do it too cause I got same problem just don't know what route too take

compressing the spring to remove it in order to put the rubber boosters on is a pain for the average Joe so they go with these instead cause it's quick and easy

@dequantelumpkin5746

4 жыл бұрын

Where do I buy this device

@JohnWRathwell

4 жыл бұрын

Any auto parts store should have them.

@jaydee8285

4 жыл бұрын

In addition to that this the best way to compress your springs to get the rubber ones off...so you can use it as a tool or a spring lifter...simple but smart engineering

see on KZread sometimes they just show the easy part they don't show the s*** they go through to get stuff done that's the problem

Thanks for video

did you disconnect the shocks entirely or just the bottom portion of the shocks? I'm trying to do this to my 07 impala but it has struts on them

@JohnWRathwell

2 жыл бұрын

Just the bottom shock mount should do.

@JohnWRathwell

2 жыл бұрын

Disconnect the bottom shock mount.

Amazing asf

Nice working

Hey I have those lifters but before I put the lifters on I tried putting my rims on and it was meeting the shock plate so you think these lifter will help me out ? Or will I need to bend my shock plate and then use the lifters?

@JohnWRathwell

2 жыл бұрын

I would have to see it.You'll figure it out.

@jdudsentertainmenttv6595

2 жыл бұрын

@@JohnWRathwell ok cool thanks

I've used those on the most heavy sedans like classic caprice and Monte carlo I've used longer stronger bolts and I've rsise them 3 to 4 inches without any problems....and then I've loaded the trunk with tools, you've to try secure them somehow because they rotate on the coil

@JohnWRathwell

3 жыл бұрын

I heard plastic ties will keep them from rotating. I haven't tried it myself.

yea its great if your springs are open enough to get them in

@JohnWRathwell

2 жыл бұрын

I had to jack the car up and disconnect the shocks to open the coils enough to get the boosters in.

@automachinehead

Жыл бұрын

@@JohnWRathwell hey, did it sort of make clunking noise? you know the metal on metal contact kind of noise?

@JohnWRathwell

Жыл бұрын

No

@automachinehead

Жыл бұрын

@@JohnWRathwell thanks

@JohnWRathwell

Жыл бұрын

No clunking.

Hi john, thanks for the video. I'm only looking for half an inch, these are height adjustable right ? These boosters are also to large for my springs, any ideas what I can do to extend so I can install?

@JohnWRathwell

4 жыл бұрын

Disconnecting the shocks will open the spring more.

@dreezyfranklin

4 жыл бұрын

@@JohnWRathwell easier said than done I'm sure:( thank u

@rhbb228

4 жыл бұрын

@@dreezyfranklin try jacking up your car so the spring would extend. Then maybe the gap would be enough so that the adjuster would fit.

@dreezyfranklin

4 жыл бұрын

@@rhbb228 thank ya!

What distance u measure between spring coil before placing spacers and aftwerwards, do u know..?

@JohnWRathwell

3 жыл бұрын

You don't have to measure anything on the coils. The spring boosters go opposite to each other. If you measure the height of the fender before you put the lifters in, after you're done both coils, you can measure how much the fender went up.

Yo se las puse a mi Nissan kicks y me subió 2 pulgadas de alfrente.

Just put some on my car today.. Seems like it's not working.. Seems like it's staying the same height no matter how many times I turn the nut.. What am I doing wrong?

@JohnWRathwell

3 жыл бұрын

If your coils are very weak, the boosters will just spread the coil in one spot. The boosters should keep the car from bottoming out and going too low. They should give a stiffer ride. I measure the height of the wheelwell before and after the boosters are installed. I've usually got a lift from 1 inch to 1 1/2 inch.

@jayrockcooksgot64

10 ай бұрын

Everything

I had coil spring clambs but my Mahidra scorpoin swing on the road heavy from 100 km I did do the whealballance and stuff can somebody advice me on the clambs please

we,re you taking them off? and can you put 4 on each spring? to lift it higher? and to be extra careful

@christinabrown5314

6 жыл бұрын

markell robinson my name is Benz. BWA I have 6 of these lifters. On each spring on a 02 Cadillac DeVille

@royalcustom960

6 жыл бұрын

markell robinson

@dontadrea7557

3 жыл бұрын

@@christinabrown5314 Whats up bro can u tell me how to put 6 on each spring n how high each 1. How your been over the yrs?

Say you have to use to I need side and do the after be honoured 80ﾟ from From each other in Do eventually tighten up the bottom bolt you didn't tighten And I guess just measure the side did make him event and then do the Exact same thing on the other side

Are those Superior Brand Coil spring helpers? I see some that look the same on Wal- Marts web site just want to be sure. added lowered springs and 2 1/2 drop spindles to my old truck but now its too low one is slightly off...I can turn the spring in the pocket with my hand. I did not know I did not have to do both the drop spindles and the lowered springs...DOH!

@JohnWRathwell

5 жыл бұрын

I don't remember the brand name, but any auto parts store has the coil spring expanders.

What is the name of this wonderful game changer

@JohnWRathwell

2 жыл бұрын

Coil spring boosters. They can also lower a car. Amazon has them.

I have a 2011 Malibu an I have heavy subs in the car can I use these to lift th3 back up

@BodyWeakDotNet

5 жыл бұрын

Yes...

Might be worthy of a patent except this places more stress on the springs which could lead to metal fatigue. UPDATE: Nevermind. You can buy these from certain retailers. I thought it was something he made.

@JamesBrown-en3zj

Жыл бұрын

You was trying to be a smart ASS LOL

I have 20" on my '92 Camry, and I used the same type metal spacers. I noticed you installed your spacers in the middle of the coil. I have mine on the bottom, the last row of the coil. From the ground to the middle of the fender is about 28" to make it look leveled. I Now, everytime I hit a bump, I feel a lol roll, and it make me nervous like I could lose control of the car. I had the car aligned, and that still didn't resolve the issue. Should I move the spacers more to the middle of the coil to give it more flexibility, when I'm driving, and stop the "roll" effect, or does it really matter where I place them?

@carltonbrown2622

6 жыл бұрын

John W Rathwell thanks my man. I was starting to get worried that I might have messed up my suspension, and wasted my money on tires, and rims. Sure couldn't have my wife driving g anything that wasn't safe, or stable. I'm jump on it early am, and I'll let you know how it turns out.

@speedfreek7778

6 жыл бұрын

Carlton Brown Ik this is old, but how did it turn out? Curious about my 94 Altima

@kevinmontoya7318

5 ай бұрын

Only 20s? Lol. Camry can fit 22s and even 23s. I had 20s on my corolla, about to throw 22s

@dontarucker114

5 ай бұрын

​@@kevinmontoya7318i have sum 20s im trying to fit on. 02 galant..but when i put them on the car drove like it was on 4 flats..and it was sum banging on the back tire..help

@kevinmontoya7318

5 ай бұрын

@dontarucker114 it should fit 20s pretty easily with the smallest tire size being 225 30 20 and a couple of series higher. Maybe 235 30 20 or 225 35 20. Inspect the tires to make sure they have a decent tred. Inspect the dot code and check the age. Old tires may look fine, but they harden like hockey pucks and throw balance off and handling. Inspect and make sure your wheels balance, too. Make sure there are no bends or dents in the wheel. Now, if all that is fine. Check your lugs. Some lugs are different depending on wheels. The cone size and pitch may differ, look at a chart online, and see if your lug nuts and wheels are correct. Hub centric rings will definitely help with vibration at higher speeds at 60-80. If you're rubbing, you can either go with stiffer springs or coil spring boosters to give you a bit of a lift and help with clearing fenders. I've used strut lift blocks and rubber coil boosters. You can find these two at any parts store. That would be the most standard issue with aftermarket wheels.

Hi John, Does it matter which coil spring? Just trying to make it sturdy so no rubbing. A little lift about half inch

@JohnWRathwell

3 жыл бұрын

Any automotive coil spring is basically the same.

What do you call the stuff you used. Thanks.

@JohnWRathwell

5 жыл бұрын

Coil spring lifters.

Where did you buy that part

@JohnWRathwell

2 жыл бұрын

any car parts supplier should have them. Amazon should have them. Go to Amazon and type coil spring boosters. There's all kinds there.

@hardmechanic1624

2 жыл бұрын

@@JohnWRathwell Can you do me a favor and send me the link for it

@JohnWRathwell

2 жыл бұрын

There's no part number on the one's I bought. Just made in China. They are universal. Go to Amazonand type coil spring boosters. I bought mine at Canadian Tire in Canada.

I used those on my cadillac bout 12yrs ago. First of all when you hit a bump the the coil spring stretches the adapters will move. They a problem! I stayed having to readjust them do too sliding and moving or coming out. SMH (This is actual fact) I was on the hwy oneday and one in the front flew off from up under the car. I heard a big clunk looked in the mirror and it was the lifter coming out bouncing across the hwy.(SMH) The ones in the back held 3 out of the 4 and one of them came off after awhile. But eventually they rusted out and broke off. It's best to use ties at the bottom to make sure they don't move or fall out To secure them. But It's to much new stuff out now to be using them cheap azz adapters in 2019-2020. Lol

@JohnWRathwell

4 жыл бұрын

There are rubber lifters also, but the best lift improvement is new over length coils or shock springs. The video is meant for a temporary fix when one can't afford new springs or shock springs.

@J68browneyez

4 жыл бұрын

O Yea no dout... Ppl got to get what they can afford. It's definitely a good quick solution.. I just spoke on my experience with using them not knocking nobody but they did serve it's purpose for me but it was just a few bad experiences. But they did last for some yrs on the before eventually rusting and falling apart. I need some now on one of my cars... Lol I thought about it.... It's been some yrs since having to mess with any of that

@GatorG588

3 жыл бұрын

U can wield them that will stop the sliding you welcome

@J68browneyez

3 жыл бұрын

@@GatorG588 That would be the best thing to do or use the ties. Personally I wouldn't weld those, cause there not worth doing all that to the spring. The ties would be better cause eventually there going to rust out anyway.. Your welcome!!! But they definitely serve its purpose.. to lift and balance out the car to the level you want it.

@Cars4theLo48

Жыл бұрын

What is out now that’s cheap and better then these ? The rubber ones?

Esistono i GOPREN sono di gomma non arruginiscono e fanno lo stesso lavoro.

How did you even stretch the spring out enough ? That’s my problem I have bc ion have the tool to spread the spring

@JohnWRathwell

Жыл бұрын

I disconnected the shock at the bottom. The spring will go full length this way.

@aintloudmilton5901

Жыл бұрын

@@JohnWRathwell ohhh I tell ya I jus tried to do it without the correct tools that very hard . Ima have to get some help and do it that way you done it

@JohnWRathwell

Жыл бұрын

I disconnected the shocks to expand the coils

Hi may i ask what size of wrench did you used for the nut?

@JohnWRathwell

4 жыл бұрын

9/16

@nhlanhlambuyazi7536

Жыл бұрын

14mm nut

Bad idea, unless it's for a 5min drive across a river or something. Still, gave a thumbs up for the 80s pr0no music.

@JohnWRathwell

4 жыл бұрын

👌🤠

Hey John what is the part called?

@JohnWRathwell

3 жыл бұрын

Coil spring boosters

Where did u buy that kinda of kit?

@JohnWRathwell

4 жыл бұрын

Amazon has them. They're under coil spring boosters.

👏👏👏👍🤩

How are these holding up now.? Thanks

@JohnWRathwell

2 жыл бұрын

I only had the lifters on for a few months. I bought new cargo coils. The lifters give the car a stiff ride. They aren't meant to be permanent. The new cargo coils give more lift and a smoother ride.

Where do I find these? What is the correct name for this item?

@JohnWRathwell

3 жыл бұрын

Amazon has them, or most auto parts stores. They're called coil spring boosters.

Do u put the spacers on the same spring or one below it?

@JohnWRathwell

Жыл бұрын

They both go in the same coil opening

@Cars4theLo48

Жыл бұрын

@@JohnWRathwell are these better then the knuckle busters rubber spacers?

@JohnWRathwell

Жыл бұрын

These usually lift higher than the rubber lifters. If the rubber rings that go around the coil are tight to get in, you'll get a smoother ride. These metal ones will lift the car, but the ride is a little stiffer.

@JohnWRathwell

Жыл бұрын

They go in the same coil space, opposite of esch other.

where can i buy them i need for my car

@JohnWRathwell

2 жыл бұрын

Most auto parts stores have them. Amazon should have them.

If I do the oposite it will work to lower the car

@user-gu4mj6pk1

6 жыл бұрын

It means yes??

@JohnWRathwell

6 жыл бұрын

Yes. You can use them as a spring lowering kit too.

@user-gu4mj6pk1

6 жыл бұрын

John W Rathwell οκ thank you

@user-gu4mj6pk1

6 жыл бұрын

It lower the car but when I load it this system is turn around the spring???

@JohnWRathwell

6 жыл бұрын

I've never tried using them as a lowering kit. Maybe someone else here can let you know how they worked for lowering springs.

where did you get em?

@wallymoyer5482

3 ай бұрын

exactly! what the hell good is the video if it doesnt tell you where to buy it?

@wallymoyer5482

3 ай бұрын

what do you even call these things?

what are they called ?

@JohnWRathwell

3 жыл бұрын

Coil spring boosters.

How and were can I find this

@JohnWRathwell

3 жыл бұрын

Amazon has them

What's the bottom 2 nuts for?

@JohnWRathwell

3 жыл бұрын

The bottom nuts lock the other nuts to prevent them from turning.

Are those sturdy? For long term use??

@JohnWRathwell

4 жыл бұрын

This is a cheap way to lift a car but, not the best way. If you can afford it, buy new heavy duty coils.

@MeeseeksNDestr0y

3 жыл бұрын

Yeah I can’t find any coils made for my car and they have been discontinued. May have to do this. Or maybe someone here can find me some ! It’s a 2007 Suzuki aerio fwd sedan

@automachinehead

Жыл бұрын

@@MeeseeksNDestr0y this is a good fix. just check it once in a while and replace it if gets rusty

man I am so pissed off I have 24s on my Crown Vic now but once I have him put on I tried to put these in my Springs where the tire shop who put my rims on try to put them in they wouldn't go long enough to fit in between the Springs so now I have my 24s on my car and everytime I hit a bump I scrub I'm not scrubbing regularly but every time I hit a small bump I feel it scrub what do I do man these supposed to fit in the springs but they won't go in my Crown Vic spring

@p63blessed49

7 жыл бұрын

+John W Rathwell what do you mean what I'm saying is the lift didn't fit into the springs it's like my screens are too low when you take the type and jacked the car they don't open enough what's the problem

@88floyd

7 жыл бұрын

you can get some knuckle bro. They are made to fit in between the crown vic springs. All you do is strew it in with a socket wrench. those strew up from this video wont work for you or you can just order cups from eBay and you will be good bro.

@kristophermcgruder5927

6 жыл бұрын

By the twist in and stack them

@dwaynejohnson9486

4 жыл бұрын

buy longer screws

@JohnWRathwell

4 жыл бұрын

Sometimes the shocks have to be disconnected so the spring will open more to install the lifters.

Im looking for these what are they called and where can i buy them Please comment back fast my tires are getting damaged

@paidoffboss2784

3 жыл бұрын

I ordered mine on Amazon