I like to use a small wood peg when I can to help with binding on small receivers, works well sometimes and not so well others hahaha. Also, the reason why on the rudder mix that you don't need any offset is that it's moving in both directions, but with the elevator you only want it to move in one direction. so the offset makes sure that it only travels the desired weight in one way. So, a weight of +50 and an offset of +50 means the lowest value is 0 and the highest is 50 (assuming it's using the raw input from the stick or a linear curve). This also means you can do things like +50 weight and -50 offset. in the case of +50 weight and -50 offset, you would get -100 at 0% stick and 0 at 100% stick. I hope that somewhat makes sense and helps give some understanding to that kind of mixing

Also make yourself up an automobile toggle switch with a full set of input and output plugs/sockets for all yor types of batteries. Trying to hold down bind buttons and plug batteries in is a mug's game. Makes finding a suitable battery easier as well.

@blowy48flyrc

2 жыл бұрын

That's a good idea mate thanks

Very informative video. Nice work.

@blowy48flyrc

2 жыл бұрын

Thanks hope I can help

Thank you sir.

RE using the FRSky receiver (which required the throttle reversed) - If you do your channel reversing on the "Outputs" page as normally recommended you will have no trouble with using the Timer on "Ths"! There are a couple of other "Gotchas" with using reversing on the "Inputs" also.

@blowy48flyrc

2 жыл бұрын

I'll have to try that

I loved your video! I always wanted to see how to link a 2-hand control in an rc car (is it possible to connect this transmitter and its receiver with any helicopter from amainhobbies, horizon hobby, rc mart? (or any helicopter that is not from aliexpress or banggood) ?) great contribution is a genius

for the press on Propeller, you can use a but of fishing line 🎣 and secure the prop, so it won't fly away but still clips of when crashing, without breaking !

Got my plane and tested a little. Seems you do not need a micro receiver to control the plane. The multiprotocol module can be used to control the plane directly. Use the V911s protocol and E119 as subprotocol. Posted a short video on my channel to show the config. Using a Jumper T-Lite transmitter.

@blowy48flyrc

2 жыл бұрын

Nice I updated my radio and the gyro switch doesn't work same as my XK f22 it doesn't work . Good luck on your maiden flight

@oscarescales9689

2 жыл бұрын

@@blowy48flyrc I have the same result with the AK 260. I'll try with a Spektrum satellite

@oscarescales9689

2 жыл бұрын

I'd just updated my Radiomaster 16tx and there is specific Luas (Multi channel namer) to solve this issue (v911s/e119 protocol) ...and now you can bind directly to the existing receiver of the plane (in others words, not necessary additional receiver)

@hussien2681

2 жыл бұрын

@@oscarescales9689 glad to hear that.. I will try this weekend.. Thanks.. 👍

@TanLyeSiong

Жыл бұрын

Hi ​@@oscarescales9689! I just manage to bind tx16s to A210 but I'm struggling to find how to turn on/off the gyro. Right now the gyro is on by default

Interesting that you got it to work from the PPM output from the A8S Blowy. So the S-bus socket will accept either S-bus or PPM and auto select from them. Some flight controls will do this and some won't. (The KingKong/LDARC Tiny Wing 450X has different inputs for the S-bus and PPM signal and the RadioLink Byme-A/D stabs will accept either) If you read all that manual there should be a section on how to swap the i-bus/S-bus output between the 2 types of signal. The A8S comes set for i-bus by default and that WILL NOT work to drive the S-bus socket! ;-)

@blowy48flyrc

2 жыл бұрын

Interesting thanks you think the XK board is top quality then

@theoztreecrasher2647

2 жыл бұрын

@@blowy48flyrc Not sure i'd say that. The V761 board and drive system is better. Also we'll have to wait and see how long the XK electrics last. Even the satellite sockets are not that important now that the full stock protocol is being tested for the Multis. It will help those with just stock Spektrum/Futaba/FRSky/Flysky etc transmitters. I wouldn't knock back 1 of those bright yellow jobbies though. Much easier for us Old Farts to find in the scrub! :D

Hello and thank you for your video. But I was wondering do you know if the transmitter that comes with the Rare Bear can be changed from Mode 2 to Mode 1? I was originally taught to fly Mode 1 and I have since tried flying on Mode 2 but I can't get my head around the elevator being on the right hand side. I have tried this many times in the RealFlight Simulator but alas I cannot fly like I can when I use Mode 1. So I have gone back to Mode 1 but the Rare Bear I have comes with a Mode 2 transmitter so that is why I am asking if you know how to convert it to Mode 1? Any help will be greatly appreciated and thank you :).

would be nice if there was an XK protocol you could connect to directly to open tx/ edge tx

I am using a Fly Sky a8s on my xk a220 but as soon as I connect the power supply to the plane the receiver will not turn on. Before putting it inside the plane I connected it to a receiver tester and tied it to my radiomaster tx16s radio and it worked

I thoroughly enjoy your videos. Very helpful. Were you able to fly the Rare Bear with an XK radio after the initial was a dud?

@blowy48flyrc

2 жыл бұрын

Thanks and yes it flys with another XK radio. It's a great plane think we need to film it again

@me262mike2

2 жыл бұрын

@@blowy48flyrc Thank you, sir. I'm new to RC flying and need a very simple RTF experience. My interest in the Rare Bear is that I love warbirds and I'd like to morph it into an FW190.

Awesome video! Do you know if you can drop in a dsmx satellite dsmp receiver? Is there a port for that for then using dsmx spektrum controller?

@blowy48flyrc

2 жыл бұрын

I don't know manual only saying dsm 3.3v its a different port to the 5v

Something that intrigues me Blowy? You have your 6G/3D switch on channel 5 via the Flysky receiver but Pascal's Multi Module Firmware (recent version) shows it on channel 7 with "Rates" on channel 6 for the V911S/E119 sub used to control the stock board. EDIT...I've just noticed that with the OMP protocol the 6G/3D switching is also shown on ch 7 and I know that when using the S-FHSS satellite for the Eachine E119 heli driven by the XK X6 Tx from the XK K110 heli, the Omphobby S/T720 planes change modes with the Gear Switch on the Tx. Generally that is on channel 5!?? Looks like some unknown position shifts are taking place somewhere? Maybe a case of "Suck it and see?" with the channel order when using satellites!

@blowy48flyrc

2 жыл бұрын

Must of changed it rates was ch5 and gyro ch6. But with my XK f22 MT99xx I did try ch5 6 7 and 8 . I'll have check it out again

Is the wltoy xk X6 transmitter compatible with this aircraft because I know someone who sells me the plane without the transmitter and I would like to know if I could link it with my XK X6 transmitter

Can you give me some instructions on how to get an XK 6 transmitter to bind with my new p-51. There’s no explain how to link(what do I do) it’s supposed to come already set up? Any help would be greatly appreciated.

Any way to reverse sticks on default transmitter mechanically mate ? Only cuz I fly mode 1

Thanks for the video! What is the spacing on the micro JST connector you used in this setup? 1mm -1.25mm spacing?

25 күн бұрын

Anyone? I ordered 2 connectors and both to big.

Hey Blowy... Could you comment on which of the WLtoys/XK warbirds fly the best, and which might better to avoid? And same question for the Eachine/Volantex warbirds? And if you think the Eachine generally fly better than the WLtoys? I have an XK T-28 that flies AWESOME...I totally love it. So then my dad bought the XK P40 thinking we'd get the same experience for him. But instead his is quite a bit slower, and FAR less stable (both with stabilization off AND with stabilization on...either way my T28 is much more stable, predictable, and controllable than my dad's P40). Thoughts?

@MrDLRu

Жыл бұрын

Have all the Volantex warbirds except the Corsair. T28, P51 and Zero don't need any weight added. Those fly pretty good out of the box in expert on TX16S. The P40 needs 3 US penny's under the motor access cover. The Spitfire needs 2 US penny's under motor cover. Stay away from the ME109, as it requires a US quarter and nickel to fly level and also the motor/gearbox mount on this plane is weak because of how they designed it.

Hello, tell me please, is it possible to bind a flysky Fs-I6x with a wiltoys f949s receiver ?

for Flysky FS-A8S , if u hold the bind button 2 second, it will switch between sbua and ibus. so after switching, it work for me... except the throttle. i also try PPM and same result, everything work except throttle. think i may have a fauty unit

@blowy48flyrc

2 жыл бұрын

Thank you for this info

@ooiak3387

2 жыл бұрын

I am also learning by baby step 😀

@ooiak3387

2 жыл бұрын

You got me started, to work on my mustang 750mm

@blowy48flyrc

2 жыл бұрын

@@ooiak3387 it's a great hobby it can be addictive

Thanks but... I tried to check where is Ground etc. on the plane plug and now it is compeltly not turning on.. Such a shame, it was verry nice plane...

Bonjour, avez vous les fichiers des modèles pour les modèles A220 et A260 sur radiomaster Tx16s ?. Merci

if you had to buy one which would you buy

Please tell me a little, Can the XK A180 F-22 fly even if I replace the transmitter with the XK A260?

@blowy48flyrc

2 жыл бұрын

No The XK f22 is a different protocol

@-aoiwaraiotoko1441

2 жыл бұрын

@@blowy48flyrc Thank you

Can i use my xks a100 (flanker) transmitter with my xks a290 plane? Thank you for your vids and help.

@blowy48flyrc

2 жыл бұрын

No these are a different protocol

@jareddakid2

2 жыл бұрын

@@blowy48flyrc thank you

@jareddakid2

2 жыл бұрын

@@blowy48flyrc but i can use the a210 with the a290 righy?

Can you switch Tx mode (mode1 and mode2) on the original XK Tx?

@blowy48flyrc

2 жыл бұрын

I just opened it up and no I definitely couldn't change the sticks there soldered on the board

Hi, can u do a video about binding a8s reciver to an cheap transmiter like standar i6 for the a220 pls, my plane will delivery in 1 week later but i don't know how to bind and setup on i6 trasmiter. Thanks u 😀

3 ай бұрын

Would be good! Or did you figure it already?

Hi is the wltoys xk a180 rc jet can bind with xk x6 transmitter?

@blowy48flyrc

2 жыл бұрын

I didn't know sorry

@suji99hettiarachchi

2 жыл бұрын

@@blowy48flyrc is the wltoys xk a180 can bind to a S fhss protocol transmitter??

@blowy48flyrc

2 жыл бұрын

I've been using MT99XX - dragon and that's stuck on 6g mode good enough for me

Is it afhds?

Will it work also in flysky fsi6?

@blowy48flyrc

2 жыл бұрын

Yep AFHD2A same protocol as your flysky fsi6 radio. I did have that radio

Can flysky i6x blind? If i don't have that controller.

3 ай бұрын

Asking same

@yourself5745

3 ай бұрын

Yas

Hello. I love your videos. Please can you explain or confirm if I'm wrong as I could be. Yes,,, I can bind these planes to anything as I'm an expert drone builder and a 3D plane pilot but I also like cheap and cheerful si I can have fun with my less experienced friends. I purchased the xk a260 and the xk 220 The throttle elevator mix is so annoying for trying to teach my friends as it's too outrages having elevator mix on a simple 4 channel plane. ( I can't switch it off for the newbi ) Thy fly pretty rubbish and the prop saver and gearbox is a joke as even in mild crashes the balance of the prop is all over the place. The gearbox is brittle and breaks. The transmitter is no good. The trims for the motor torque is quiet extreme. Generally this batch of planes are a bad copy of the voltantex and sonik range. Voltantex and sonik are simply fantastic. Is this just me or are xk becoming bad at what they do at this time in there evolution. Rewire...

@blowy48flyrc

2 жыл бұрын

Yes we probably like the volantex/ eachine planes better and hopefully last longer but planes don't like crashing these mini ones can get away with it only because they're light