This video is about Jeff's How-to Balance Dirt Bike Tires
Жүктеу.....
Пікірлер: 65
@zw810Ай бұрын
Thanks Jeff! I’ve got fresh tires and Tubliss set up landing sometime this week from y’all. I had a old Pitbull stand that doesn’t fit any of my current bikes, I was going to order a tire balancer but I’ll just stop by the hardware store and spend 7 bucks on a steel tube to put in between the arms! Thanks for all you do.
@slaverace1
26 күн бұрын
You are welcome.
@dannuthals70454 жыл бұрын
Thanks Jeff! After watching this video I went into the garage and built a simple inverted T-frame out of scrap 2x4, found an old rod for the "axle" and built a rig. Nothing fancy, but it will work. Will order the weights from you and look forward to balancing my Tubliss wheels for my 500 EXC-F. Knew I should do this - thanks for the solution.
@philstewart24732 жыл бұрын
Thanks Jeff for this balancing video, and all the other vids you post. Simple and precise, what could be better. Keep up the great service you provide to us wrenchers!
@slaverace1
2 жыл бұрын
You're welcome.
@Johnr37us3 жыл бұрын
I actually purchased a machine like this last week ( before I seen this video) because after doing my research this was a very good way to balance a dirt bike tire.
@oneeyedrone42932 жыл бұрын
working on balancing a sprocket on an older mini bike now, its a real pain but not as dangerous as a dirt bike. Great video for the balancing steps, once sprocket gets sorted out on mine / replaced
@markbuckholz3184 Жыл бұрын
Hahah, Mr Slavens, I have the same truing stand from probably 40 years ago, gawd we are getting old. Thank you for your reviews on IRC rears and the Bridgestone X31. I live in Flagstaff, and have used up my stash of Kenda pro deal tires. Picked up a new 300TBI, am working thru all the dumb things KTM did for this new bike, and started looking at the new generation of tires, going to try a VE33s/x31 combo, should be good for the variety of stuff I am training and racing on here in the southwest. Hope to cross paths with you again up in the Taylor Park/Salida area again sometime this coming summer. Thank you for the AXP skidplate for my 300TBI, it is holding up great so far in the nasty boulder fields we like to ride on in Arizona. Cheers!
@patrickmatthews12724 жыл бұрын
Thanks Jeff for the vid funny how we forget the old school ways , something I need to do now 👍👍
@sashapave94004 жыл бұрын
@Jeff thanks for this, I hope it helps more people change & balance their own tires. Couple questions: - I've seen some people stack their spoke weights on top of each other. I tend to spread out across multiple spokes. Is one way correct? - Any opinion on MotionPro LiteLock rim locks vs. the regular variety?
@fje86873 жыл бұрын
Thanks Jeff! Worked perfect
@slaverace1
3 жыл бұрын
You're welcome!
@adventuresoftheindian52033 жыл бұрын
Best balance video, hands down.
@slaverace1
3 жыл бұрын
Thank you.
@jasonl4954 жыл бұрын
Thanks Jeff!
@mattkeno24053 жыл бұрын
I just use two rimlocks, drill another rimlock hole directly opposite the existing one and run two of the same rimlocks, pretty balanced and you have two points locking the bead instead of one.
@KrinklingPlasticBits
Жыл бұрын
Rear yes, front no way
@Matt-rn6ve3 жыл бұрын
Great video! Where do you get those weights?
@jimcline8694 Жыл бұрын
Thanks Jeff
@craighoffman81604 жыл бұрын
Jeff, Glad to hear you are out riding and apparently feeling better after your car accident. Those spoke weights are cool! Much better than screwing around with stick on deals that always fall off or the crimp on lead fishing weights and other Mickey Mouse stuff I have used with varying levels of success and failure. Been static balancing like this forever as well. Will order some of those weights from ya.
@slaverace1
4 жыл бұрын
It was a motorcycle vs Sprinter van head-on.
@sashapave9400
4 жыл бұрын
@@slaverace1 Damn! Glad you're still with us!
@craighoffman8160
4 жыл бұрын
@@slaverace1 Knew it was bad, but did not know the details. Holy crap. Glad to still have ya with us.
@jameswilson2423Ай бұрын
That is awesome 😎
@slaverace1
Ай бұрын
Thank you.
@mototrailz4 жыл бұрын
Thanks jeff. The only negative about those weight is you have to take them off when tightening the spokes
@slaverace1
4 жыл бұрын
Takes 2 seconds. Less time than to pop the top off a beer.
@FatherFulmer Жыл бұрын
Do you have to balance both tires, front and back?
@timmoore66563 жыл бұрын
Thanks
@jbtek12 жыл бұрын
Great video! I'm not sure I would trust the allen head set screw to stay tight. I've had good luck with the crimp on lead weights.
@slaverace1
2 жыл бұрын
It takes very little force to keep them intact. The screws work very well.
@MRKTM690smc4 жыл бұрын
I’m surprised it isn’t off more with not having the wheel centered on the shaft. I used some machined cones with some high precision bearings on shaft and it works great.
@slaverace1
4 жыл бұрын
The offset has no effect.
@johncorbishley1548
3 жыл бұрын
Jeffs way has less friction
@jmotoid36614 жыл бұрын
Jeff what’s your opinions on stick on rim weights? Good as spoke weights? I was considering those over spoke types.
@slaverace1
3 жыл бұрын
You have to use a lot of the stick-on type and they get knocked off.
@johnroethel55274 жыл бұрын
Funny how the old school ways are at least as accurate, often more. LOL
@WorldCommander10 ай бұрын
I like simple! But, how come the offset doesn't make any difference in accuracy?
@uloveit6664 жыл бұрын
I often ride to work on my 2002 ktm 300 and when my shadow is next to me I laugh at how much my rear wheel bounces up and down at 70mph. I should really try this out!
@sashapave9400
4 жыл бұрын
You're very lucky to live in a state that allows 2-strokes on the road, then again maybe your commute is all dirt :)
@uloveit666
4 жыл бұрын
@@sashapave9400 I live in the UK dude so it's not problem for us 👌
@BudderCraft526
3 жыл бұрын
@@sashapave9400 www.dirtlegal.com/services/dirt-bike-conversion maybe give this a shot😉
@waspmeat3 жыл бұрын
anyone know the this brand specifically of weights he’s using or where to source them?
Bought your weights for my FE501 after installing mousse and the large end does not fit over the nipples on my OEM wheels
@slaverace1
5 ай бұрын
Hello Erik: The spoke weights do not just slide on, you must loosen the screw then tap the weight with a hammer.
@crfisaiah39632 жыл бұрын
So the rim lock is at balanced is at the bottom?
@slaverace1
2 жыл бұрын
Sorry, I don't understand your question.
@crfisaiah3963
2 жыл бұрын
@@slaverace1 so when the wheel is balanced is the rim lock at the bottom
@slaverace1
2 жыл бұрын
@@crfisaiah3963 No. When it is balanced, the rim lock should not stop in the same place every time.
@crfisaiah3963
2 жыл бұрын
@@slaverace1 right thank you
@bryanha794 жыл бұрын
2.5 ounces on the opposite side of the rim lock works almost every time.
@slaverace1
4 жыл бұрын
Should get you close but some rim locks are heavier than others and may need more or less weight.
@ToyotaKTM
4 жыл бұрын
Some knoby TIRES are out of balance, by up to 1/4 the weight of the rimlock. Tublis throws in a second valve stem to consider.
@GaryRolls24 жыл бұрын
i bet this will make a huge difference for the first 30 seconds of riding, after that mud will will get it out of whack.. pointless🥵
@slaverace1
4 жыл бұрын
Wrong.
@moto5914
3 жыл бұрын
@ Joe Rohloff. If you are going to apply that logic... you don’t tune your suspension for your ride weight either since it pointless once mud starts sticking? Don’t tune your carb since you ride in hills and different temps anyway?
Пікірлер: 65
Thanks Jeff! I’ve got fresh tires and Tubliss set up landing sometime this week from y’all. I had a old Pitbull stand that doesn’t fit any of my current bikes, I was going to order a tire balancer but I’ll just stop by the hardware store and spend 7 bucks on a steel tube to put in between the arms! Thanks for all you do.
@slaverace1
26 күн бұрын
You are welcome.
Thanks Jeff! After watching this video I went into the garage and built a simple inverted T-frame out of scrap 2x4, found an old rod for the "axle" and built a rig. Nothing fancy, but it will work. Will order the weights from you and look forward to balancing my Tubliss wheels for my 500 EXC-F. Knew I should do this - thanks for the solution.
Thanks Jeff for this balancing video, and all the other vids you post. Simple and precise, what could be better. Keep up the great service you provide to us wrenchers!
@slaverace1
2 жыл бұрын
You're welcome.
I actually purchased a machine like this last week ( before I seen this video) because after doing my research this was a very good way to balance a dirt bike tire.
working on balancing a sprocket on an older mini bike now, its a real pain but not as dangerous as a dirt bike. Great video for the balancing steps, once sprocket gets sorted out on mine / replaced
Hahah, Mr Slavens, I have the same truing stand from probably 40 years ago, gawd we are getting old. Thank you for your reviews on IRC rears and the Bridgestone X31. I live in Flagstaff, and have used up my stash of Kenda pro deal tires. Picked up a new 300TBI, am working thru all the dumb things KTM did for this new bike, and started looking at the new generation of tires, going to try a VE33s/x31 combo, should be good for the variety of stuff I am training and racing on here in the southwest. Hope to cross paths with you again up in the Taylor Park/Salida area again sometime this coming summer. Thank you for the AXP skidplate for my 300TBI, it is holding up great so far in the nasty boulder fields we like to ride on in Arizona. Cheers!
Thanks Jeff for the vid funny how we forget the old school ways , something I need to do now 👍👍
@Jeff thanks for this, I hope it helps more people change & balance their own tires. Couple questions: - I've seen some people stack their spoke weights on top of each other. I tend to spread out across multiple spokes. Is one way correct? - Any opinion on MotionPro LiteLock rim locks vs. the regular variety?
Thanks Jeff! Worked perfect
@slaverace1
3 жыл бұрын
You're welcome!
Best balance video, hands down.
@slaverace1
3 жыл бұрын
Thank you.
Thanks Jeff!
I just use two rimlocks, drill another rimlock hole directly opposite the existing one and run two of the same rimlocks, pretty balanced and you have two points locking the bead instead of one.
@KrinklingPlasticBits
Жыл бұрын
Rear yes, front no way
Great video! Where do you get those weights?
Thanks Jeff
Jeff, Glad to hear you are out riding and apparently feeling better after your car accident. Those spoke weights are cool! Much better than screwing around with stick on deals that always fall off or the crimp on lead fishing weights and other Mickey Mouse stuff I have used with varying levels of success and failure. Been static balancing like this forever as well. Will order some of those weights from ya.
@slaverace1
4 жыл бұрын
It was a motorcycle vs Sprinter van head-on.
@sashapave9400
4 жыл бұрын
@@slaverace1 Damn! Glad you're still with us!
@craighoffman8160
4 жыл бұрын
@@slaverace1 Knew it was bad, but did not know the details. Holy crap. Glad to still have ya with us.
That is awesome 😎
@slaverace1
Ай бұрын
Thank you.
Thanks jeff. The only negative about those weight is you have to take them off when tightening the spokes
@slaverace1
4 жыл бұрын
Takes 2 seconds. Less time than to pop the top off a beer.
Do you have to balance both tires, front and back?
Thanks
Great video! I'm not sure I would trust the allen head set screw to stay tight. I've had good luck with the crimp on lead weights.
@slaverace1
2 жыл бұрын
It takes very little force to keep them intact. The screws work very well.
I’m surprised it isn’t off more with not having the wheel centered on the shaft. I used some machined cones with some high precision bearings on shaft and it works great.
@slaverace1
4 жыл бұрын
The offset has no effect.
@johncorbishley1548
3 жыл бұрын
Jeffs way has less friction
Jeff what’s your opinions on stick on rim weights? Good as spoke weights? I was considering those over spoke types.
@slaverace1
3 жыл бұрын
You have to use a lot of the stick-on type and they get knocked off.
Funny how the old school ways are at least as accurate, often more. LOL
I like simple! But, how come the offset doesn't make any difference in accuracy?
I often ride to work on my 2002 ktm 300 and when my shadow is next to me I laugh at how much my rear wheel bounces up and down at 70mph. I should really try this out!
@sashapave9400
4 жыл бұрын
You're very lucky to live in a state that allows 2-strokes on the road, then again maybe your commute is all dirt :)
@uloveit666
4 жыл бұрын
@@sashapave9400 I live in the UK dude so it's not problem for us 👌
@BudderCraft526
3 жыл бұрын
@@sashapave9400 www.dirtlegal.com/services/dirt-bike-conversion maybe give this a shot😉
anyone know the this brand specifically of weights he’s using or where to source them?
@slaverace1
3 жыл бұрын
slavensracing.com/shop/reusable-spoke-weights-by-no-mar/
@qb7384
Жыл бұрын
Can you run two rim locks or is that a bad idea?
Couldn't you do this with the rim left on the bike by disconnecting the caliper and the bike jacked up?
@slaverace1
3 жыл бұрын
Yes, but the bearing and seal drag makes it more difficult to get an accurate setting.
Where did you get the weights?
@slaverace1
2 жыл бұрын
slavensracing.com/shop/reusable-spoke-weights-by-no-mar/
Bought your weights for my FE501 after installing mousse and the large end does not fit over the nipples on my OEM wheels
@slaverace1
5 ай бұрын
Hello Erik: The spoke weights do not just slide on, you must loosen the screw then tap the weight with a hammer.
So the rim lock is at balanced is at the bottom?
@slaverace1
2 жыл бұрын
Sorry, I don't understand your question.
@crfisaiah3963
2 жыл бұрын
@@slaverace1 so when the wheel is balanced is the rim lock at the bottom
@slaverace1
2 жыл бұрын
@@crfisaiah3963 No. When it is balanced, the rim lock should not stop in the same place every time.
@crfisaiah3963
2 жыл бұрын
@@slaverace1 right thank you
2.5 ounces on the opposite side of the rim lock works almost every time.
@slaverace1
4 жыл бұрын
Should get you close but some rim locks are heavier than others and may need more or less weight.
@ToyotaKTM
4 жыл бұрын
Some knoby TIRES are out of balance, by up to 1/4 the weight of the rimlock. Tublis throws in a second valve stem to consider.
i bet this will make a huge difference for the first 30 seconds of riding, after that mud will will get it out of whack.. pointless🥵
@slaverace1
4 жыл бұрын
Wrong.
@moto5914
3 жыл бұрын
@ Joe Rohloff. If you are going to apply that logic... you don’t tune your suspension for your ride weight either since it pointless once mud starts sticking? Don’t tune your carb since you ride in hills and different temps anyway?
@GaryRolls2
3 жыл бұрын
@@moto5914TPI is tuned to perfection 🥴