At 67 I really really needed this instruction! Bravo! Just had my deck installed yesterday. I will replay it all tomorrow 0500hrs as its 108 outside

@pioneerelectronics

Жыл бұрын

I hope you enjoy your new receiver. Thank you for your business. You can find a full playlist of How To videos from Pioneer about audio receivers here: kzread.info/dash/bejne/pqNmx7qFgKXUeqw.html You can find more videos on Pioneer's KZread Channel here: kzread.info

I’m a HUGE fan of Network Mode and it’s kind of a Pioneer exclusive.

@pioneerelectronics

3 жыл бұрын

You can find more information about Network Mode and the crossover and slope settings in this Pioneer video: kzread.info/dash/bejne/iap-uruhZtnRj5M.html You can find more videos on Pioneer's KZread Channel here: kzread.info

I was fn wondering why the hell I can't find the SLA setting,,,, duh I'm on radio lol... ur video saved me thanx

@pioneerelectronics

Жыл бұрын

You can find a full playlist of How To videos about Pioneer in-dash receivers here: kzread.info/dash/bejne/ZmZ5rsGDd7vJetY.html You can find more videos on Pioneer's KZread Channel here: www.youtube.com/@pioneerelectronics

Hi, just bought a mvh-s720bhs...it doesn't have the band pass settings (one of the main reasons I bought it) just rear and sub. No low pass for the mid...what can I do? Thanx

@pioneerelectronics

2 жыл бұрын

You have the receiver set up in Standard Mode. That's a mistake. You want the receiver setup in NETWORK MODE. The Pioneer MVH-S720BHS must be set up in NETWORK MODE in order to have the band pass output. The Pioneer MVH-S720BHS certainly has band pass output, when used in NETWORK MODE. Don't worry, it's not difficult to set up your MVH-S720BHS in NETWORK MODE and have the band pass output. Just follow these simple instruction it only take a few minutes: Step 1. With the vehicle safely parked, and the engine running and the receiver powered up, Press and hold the receiver's SRC button for a few seconds. This will turn the receiver off. Step 2. Press in on the Volume control. This will show the Initial and System Menu. Turn the volume control to see INITIAL. Press in on the volume to select INITIAL. Step 3. Once you've selected the INITIAL menu, turn the volume control to SYSTEM RESET. Press in on the volume control to select SYSTEM RESET. Step 4. Press in on the volume control to Reset the receiver, and press in on the volume control again to confirm YES and Reset the receiver. Step 5. The receiver will display RESETTING for several seconds. DO NOT TURN OFF THE VEHICLE'S ENGINE. After the reset is complete, the receiver will automatically restart and display the Language Setting. Step 6. Select the Language you want. Press in on the volume control to confirm. The receiver will display the Clock Set Screen. Step 7. Set the clock by using the volume control and pressing in to confirm. Step 8. Don't Miss this step. This is the important one. The receiver will display > SPEAKER MODE Step 9. In SPEAKER MODE, you have 2 options. Turn the volume control to NETWORK MODE. Don't choose Standard Mode. You want NETWORK MODE. Press in on the volume control to confirm NETWORK MODE. Step 10. Confirm YES, you want NETWORK MODE. Press in on the volume control to confirm NETWORK MODE. Step 11. The receiver will ask if you want to quit the setup menu. Confirm Yes. Now you're system is setup in Network Mode and you have an HFP on the Front RCA's, and you have an LPF and an HPF on the Rear RCA's, and you have an LPF on the Sub-out RCA's. You can lean more about NETWORK Mode in this How To video from Pioneer: kzread.info/dash/bejne/nWelkrymZc3ceMo.html Please watch this with the sound on. You can learn more about using Crossover's and Slope setting in this How To video from Pioneer: kzread.info/dash/bejne/iap-uruhZtnRj5M.html Please watch this with the sound on. You can download the owner's manual for the Pioneer MVH-S720BHS here: www.pioneerelectronics.com/StaticFiles/Manuals/Car/MVH-S720BHS_OperationManual102620.pdf You may find page 27 of some interest. Please be sure to install the latest firmware for your Pioneer MVH-S720BHS. You can find it here: www.pioneerelectronics.com/PUSA/Car/Digital+Media+Receivers/MVH-S720BHS#downloads You can find more videos on Pioneer's KZread Channel here: kzread.info

Does it have a volume control for the sub only on normal mode?

@pioneerelectronics

2 жыл бұрын

Please clarify your question. Do you mean Normal / Network mode? Or do you mean Normal or Reverse Phase for the subwoofer output? What is the model number of your Pioneer in-dash receiver? Be sure to have the subwoofer output switched on. Depending upon your receiver model number, the Subwoofer Level control may be in the subwoofer settings, or it may be in the Speaker Level settings. You can learn more about is in this How To video from Pioneer: kzread.info/dash/bejne/eoh-kpmfm5etotY.html I recommend to watch the video with the sound on. You can find more videos on Pioneer's KZread Channel here: kzread.info

Any idea why the subwoofer control settings also adjusts my rear door speakers and if i turn subwoofer off on the head unit it also turns off both rear speakers??Please any help would be greatly appreciated

@pioneerelectronics

3 жыл бұрын

What is the model number of your Pioneer in-dash receiver?

@TrollRaper69

3 жыл бұрын

@@pioneerelectronics its an mvh S622BS and i figured it out lol.I had the receiver in SW mode for the initial range of output instead of FULL so i reset the unit and set it to FULL range and now i have an adjustable fader and the subwoofer setting is isolated to,get this,the subwoofer haha whoohoo..Thanks for the response anyhow..have a great weekend

Why do I get a lot of distortion I have a MVH-320bt and have orion speakers like at 35 of volume ??

@pioneerelectronics

2 жыл бұрын

This is a long answer. Please take a few minutes and read the complete answer. If you are using a hammer and you hit your thumb, don't blame the hammer. The goal is to create an audio system with little or no distortion. If the in-dash receiver's RCA outputs clip they create a distorted audio signal. That distorted audio signal is then in turn amplified by the subwoofer amp or other amplifiers in the system. In a well designed and set up audio system, you should be able to turn up the master volume to, or near it's maximum, and not hear any distortion from the speakers in the system. If you have all of these settings (for example: EQ, speaker levels, crossover levels, bass boost etc...) set to zero or lower you should be able to turn the volume up to it's max, and the RCA outputs of the in-dash receiver should not clip and create distortion that will in turn be amplified by your system. If you add in a boosted signal on the in-dash receiver from any of the audio controls (for example: EQ, speaker levels, crossover levels, bass boost etc...) this may cause the in-dash receiver's RCA outputs to clip and create distortion at high output levels. So... Here is an example: This is hypothetical, please don't take the numbers literally and try to translate them to any given in-dash receiver. In this best case scenario I have excellent amplifiers and well matched speakers. My in-dash receiver master volume control has a maximum volume level number of 50. I have all of the audio settings set to zero, and I can turn up the master volume to 50 and the RCA outputs do not clip. I set the gains on the amplifiers so that there is no distortion. That's what I want. Now, I add in a subwoofer level control adjustment of +5. When I turn up the master volume I can get to only volume level 45 before I begin to hear distortion coming from my speakers. If I add in an EQ adjustment on the 80Hz frequency band of +4, my master volume begins to distort now at volume level 41. Remember I started at volume level 50 with no distortion. Please note this is just a hypothetical example. In this example, the in-dash receiver is causing the distortion and sending that distorted signal to the amplifiers. The amps and speakers are simply doing the job they were designed to do. What's the solution? Use the audio controls to your best advantage. If you set them to zero or lower, your in-dash receiver shouldn't be creating noise. Set the gain controls on your amplifiers so you don't hear any distortion at high volume levels. If you want to add in a +1 or +2, that's OK as long as you realize you may be getting distortion at the highest volume levels. You need to find the settings that works best for you. If you are trying to balance your system so all of the speakers are at or near the same volume level, consider lowering the volume level of some speakers rather than raising the volume level of one individual speaker. If you are using Bluetooth Audio as your main music source, consider lowering the volume level on the Phone. It's possible, the phone is overloading the input through Bluetooth Audio, and the distortion is beginning right there. If you set the volume level on the phone lower, you may be able to turn up the master volume level on the in-dash receiver with less distortion. If you want more volume, you might want to consider a more powerful amplifier and speakers. You can find more videos about Pioneer NEX in-dash receiver's here: kzread.info/dash/bejne/gpl8wcpxhavgcto.html and you can find more videos on Pioneer's You tube Channel here: kzread.info

What about sound quality or fidelity? It says RCA's are 4v output? Does this improve better sound quality than older version of pioneer receiver? I think on buy one but I'm not sure about sound quality... I'm audioholic!

@pioneerelectronics

Жыл бұрын

The Pioneer FH-S722BS is an excellent sound quality CD receiver. It has 3 sets of RCA outputs for operating external amplifiers. You can see an unboxing video from Pioneer here: kzread.info/dash/bejne/nYWuls2ucpXLnpc.html The RCA outputs can be setup as Front, Rear, and Subwoofer output, or for more control and better sound quality, as High, Mid, and Low output. You can learn more about Pioneer's Standard Mode and Network Mode setup here: kzread.info/dash/bejne/nWelkrymZc3ceMo.html You can learn more about using Pioneer's receiver's built-in crossovers and slopes in this How To video from Pioneer: kzread.info/dash/bejne/iap-uruhZtnRj5M.html For higher sound quality and Hi Res Audio certified products please consider the Pioneer DMH-WT8600NEX seen here: kzread.info/dash/bejne/g6aqsM2Al7XVZ6g.html You can find more videos on Pioneer's KZread Channel here: www.youtube.com/@pioneerelectronics

@greatmind3823

Жыл бұрын

Yes ... if u have aftermarket amplifiers in ur car ... then they will shake ur hand for feeding them voltages ... the amplifiers will produce better , cleaner signal ... and u can most likely max out ur volume on the headunit

My screen is not bright enough.. When I am driving I can barely see it ..How do I fix this?

@pioneerelectronics

2 жыл бұрын

Please be sure the in-dash receiver's Dimmer function is switched off in the daylight hours. Also be sure the receiver's brightness is set to 10 in the daylight hours. The Pioneer FH-S52BT has a dimmer switch on the front of the receiver. It's the Band-Dimmer button or the arrow back button. Press and hold for a few seconds and this will switch the dimmer function on and off. You can learn more details about the dimmer and brightness function in this How To video from Pioneer: kzread.info/dash/bejne/ooF_t7Kcd6iYZsY.html You can find more How To videos about Pioneer FH-S52BT here: kzread.info/dash/bejne/pqNmx7qFgKXUeqw.html and you can find more videos on Pioneer's KZread Channel here: kzread.info

How do you reset radio stations on model# deh54010bt

@deckerdotto6035

3 жыл бұрын

Here is a video about tuner operation for a Pioneer receiver in 2020: kzread.info/dash/bejne/oHyntraFnqfKf9I.html You don't need to erase the old radio station presets. Just create new ones. I don't know what a Pioneer DEH54010BT is. Please check the model number again. If you want reset the in-dash receiver back to it's factory settings, I recommend to do a system reset. You can see it here: kzread.info/dash/bejne/Zqyaj9Scaayrn84.html You can find a full playlist of How To videos from Pioneer about DEH-S4200BT here: kzread.info/dash/bejne/pqNmx7qFgKXUeqw.html and you can find more videos on Pioneer's KZread Channel here: kzread.info

Im getting the fh-s722bs on 1st set up if i only have 1 amp n subs and don't know that much of sound set up what is best setup for the hu i do want to use the time aliment

@pioneerelectronics

Жыл бұрын

Please be more specific with your question. If you have one amp for full range speakers, and a separate amp for your subwoofer you may want to use the Standard Mode setup. You can learn more the difference between Network Mode and Standard mode in this How To video from Pioneer: kzread.info/dash/bejne/nWelkrymZc3ceMo.html Please watch the video with the sound on. To understand more about using crossovers and slopes, please take a look at this How To video from Pioneer: kzread.info/dash/bejne/iap-uruhZtnRj5M.html Please watch the video with the sound on. You can find more videos on Pioneer's KZread Channel here: www.youtube.com/@pioneerelectronics

@almann5798

Жыл бұрын

@@pioneerelectronics sorry i will be using the headunit for mids and highs and an amp for my subs i do not know alot bout set ups so was wonder what would be best for this set up

@pioneerelectronics

Жыл бұрын

@@almann5798 Please be more specific. Mids and highs. OK. Do you mean separate tweeters, and separate mid bass drivers? Or do you mean for example 6x9 inch speakers in the doors for your mids and highs? Each of the speakers playing mids and highs together? It makes a big difference on the setup.

@almann5798

Жыл бұрын

Sorry see i do not know the terms well ill be using coaxial speakers to run off of my head unit

@almann5798

Жыл бұрын

So there will be 5.25 coaxial speaker in front door and coaxial 6x9 in rear back deck

Does the S622bs have network mode?

@pioneerelectronics

2 жыл бұрын

Yes, the Pioneer MVH-S622BS has Network Mode and Standard Mode setup. You can learn more about MVH-S622BS in this Pioneer unboxing video: kzread.info/dash/bejne/l4iOpauYfJufeaw.html You can find a full playlist of How To videos from Pioneer about MVH-S622BS here: kzread.info/dash/bejne/lGl4z9eMfcaWZKg.html You can find more videos on Pioneer's KZread Channel here: kzread.info

I can't get signal to my amp new RCA jacks new amps

@pioneerelectronics

3 жыл бұрын

What is the model number of your Pioneer in-dash receiver? Are you certain the amplifier is switched on? RCA cables can occasionally be the problem. Please check with a different cable. I recommend to press the receiver's microprocessor reset button. You can see it in this Pioneer how to video: kzread.info/dash/bejne/oWqdw9mJYpqfgpc.html or for a 2 DIN receiver here: kzread.info/dash/bejne/iYVs0pqbaNnAe8Y.html If you are the subwoofer output please be sure the Subwoofer Output is switched on. You can see it in this Pioneer How To video: kzread.info/dash/bejne/loGnro9updrVl9o.html You can find more videos on Pioneer's KZread Channel here: kzread.info

@Waynerebelrider

3 жыл бұрын

@@pioneerelectronics fns52bt, I had to turn the sub level way up,

@pioneerelectronics

3 жыл бұрын

Please consider experimenting with the amplifiers gain control. I recommend to set the receiver's subwoofer output to zero, and adjust the amplifiers gain control to a more compatible setting. The amplifiers gain control is a way to balance the output from the receiver with the input to the amplifier.

@Waynerebelrider

3 жыл бұрын

@@pioneerelectronics thanks