#howto#assembly#aircompressorpressureswitch ⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️ please like share and subscribe for more tutorial videos thanks
Жүктеу.....
Пікірлер: 96
@CaseyE-bn3vk2 ай бұрын
Thank you so much for this video , I would have been screwed without it.
@user-wl6od3to7h Жыл бұрын
so, where does the black plastic piece go that seemed to disappear around 3:40...
@jamesdaul8540
Жыл бұрын
I think that should have been the first thing to go in!!!
@jameslandry9544
10 ай бұрын
Amen slight of hand but no help smh
@smittyschmid5457
4 ай бұрын
I came here to say the same thing. 😳
@jerryayers7337
3 ай бұрын
@@jamesdaul8540It slides in vertically and part of it stick out the top of the housing (reset button). Only goes in one way.
@tv-xp7tw3 ай бұрын
رااااااائعة رااااااائعة بزاااف يا اخي عزيز دائما تواصل معك يا احلى واجمل قناة 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@stoker2024 күн бұрын
You have extra long screws to hold the switch to the plate. There's no room for the thickness of twist ties with the shorty screws on what I have. If you're watching the video it's obvious the plastic piece has to go in first and he had to take it apart to put it in. After multiple attempts using various methods, it was a thin wire that worked for holding things together and still being able to remove it. I also drilled a hole and wired the back end of the pressure plate. That's the critical part that always wants to pop out when you're trying to put it together. What a PITA I finally got it working like new. The problem was the gasket leaking air and now it doesn't.
@jameslandry954410 ай бұрын
I like how you cut the film and then put the plastic piece in that you forgot to put in in the beginning lil shady I didn't watch anymore🤨👎
@ethelbertjrtan7566
9 ай бұрын
😅😅😅
@aaahandy
5 ай бұрын
Did you catch him with his pants down?
@smittyschmid5457
4 ай бұрын
I came here for this same comment. 🤷🏼♂️
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@LetswalkaroundGothenburg32 ай бұрын
Amazing video Have a Good time
@tletechcherАй бұрын
L431 idol. maraming salamat sa pagbahagi ng iyong kaalaman at kakayahan, kabisado mo talaga lods
@nicholasbenton7698 Жыл бұрын
I could not get this switch back together without this video. Thank you for posting this!
@CaseyE-bn3vk
2 ай бұрын
I took mine apart and damn it went everywhere… couldn’t figure it out.. maybe this video will help.
@dianacarlos52102 ай бұрын
Galing naman idol.thanks for sharing.God bless
@Lovy20115 ай бұрын
L350 you are so very skilled hand ,sir. Good job❤
@popisvlogs82863 ай бұрын
Great knowledge
@tanveernaeem1157 Жыл бұрын
Great video! Thanks os sharing. I have a very similar ressue switch that I need to put back together and this video should really help. One question though. There was a small plastic piece sitting next to the switch cover at 02:40, but not sure where did it go. I did not see you putting that piece in the assembly.
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@tanveernaeem1157
3 ай бұрын
Thank you so very much. Much appreciated.
@gracelentv351719 күн бұрын
Thank you for sharing po.
@probinsyanonghardinero4 ай бұрын
Nice sharing lods watching full
@dhen-lyntvsvlog22822 ай бұрын
Good morning thanks idol for sharing this video stay connected
@lourdeswasin5715 Жыл бұрын
Nice sharing host , really you're expert in this mechanical electronics
@lilhemy100811 ай бұрын
Great tutorial, thank you for the knowledge you shared..👍 full watched... Have a wonderful day my friend
@merliebobis30016 ай бұрын
Great vedios
@AMIGOS-AMIGAS3 ай бұрын
Magandang pagbabagi ng iyong video 🎉magandang panoorin hanggang sa wakas at para itoy suporta din nilang kaibigan
@user-jc1ny6fv8t Жыл бұрын
kailangan talaga marunong angg kabit ng ganyan buti nkita ko vedio mo maramong salamat
@barciabrotherstv48134 ай бұрын
Again watching your video friend.nice sharing.❤❤❤
@technoyvlogs36144 ай бұрын
Watchiing kabayan..salamat sa pah share ng video
@dhiemazarya52965 ай бұрын
Assembly air compressor pressure switch , good
@relbvlog1985 Жыл бұрын
Hello sir watching replay here . Thank you for sharing this tutorial video. Thank you for sharing and visiting my house. Stay connected. God bless.
@renzboycaspe4 ай бұрын
galing mo lods
@ZilongLongzi11 ай бұрын
thanks for sharibg lods
@bigbadhag Жыл бұрын
Thanks for your help! If it would have flew apart slower, maybe I'd seen where everything went!
@robertbarton26882 жыл бұрын
Thank you so much for this video. I am fixing up a Craftsman air compressor and it has a very similar switch. Using the Vise Grips was genius!!
@simplydenzvlog Жыл бұрын
WOW so nice... Good job.... Thank you for sharing...
@fulmo2n10 ай бұрын
Lots of Thanks 🎉🎉🎉 I solved da problem 4m yo video. Thanks 👍👍👍
@soctechtv
10 ай бұрын
Welcome 👍
@lengallannetwork Жыл бұрын
Informative, great tutorial! Job well done, keep on sharing your knowledge , ha e a great time, enjoy!
@pagtukaw96572 жыл бұрын
Thanks for sharing your ideas
@endicktvvlogs9297 Жыл бұрын
Watching fullpack po
@RoadToMythical4 ай бұрын
Galing lods thanks for sharing napaka husay ng pag kakagawa at napaka pulido ❤❤❤
@jjooms511 ай бұрын
2:58 you have the black plastic peice with the odd shape l. Where did you put that..
@nenengalma5 ай бұрын
Good work assembled host ang galing
@nalztv8179 Жыл бұрын
Nice lods galing....
@queenlec7845 Жыл бұрын
Great help po. Thank you for sharing.
@sillingsonrmarakmixtv8897 Жыл бұрын
Wow nice sir
@claudiomahinayvlog3 ай бұрын
Salamat sa pagbahagi idol malaking tulong ito.. God bless mabuhay ka..
@corgsponscabin57798 ай бұрын
Eto yung nakatulong sakin ngayon. Maraming salamat po
@Jayzee420 Жыл бұрын
Ayos Lodi nice content keep vlogging po god bless
@narolmya Жыл бұрын
Thank you for always sharing videos that give the audience a new perspective and true image of you and the place you want to convey. I am sure, you already have a loyal audience, including me, who love the authenticity of each video. Keep moving forward and work hard every day, I will always watch full videos with ads to support you
@shisholy7828 Жыл бұрын
Thank you, I spent a lot of time trying to get this contraption together. Nearly drove myself nuts. Your technique solved the mystery for me. After taking this thing apart and ordering a new switch I realized it was just a simple reset button on the motor. I put it all back together following your technique and all works great. As one of your viewers noted the black plastic piece goes in Pryor to the spring attachment. Plastic ties and vise grips were the secret 👍 Have a backup pressure switch and thorough knowledge of what to do now. 🤬🤬🤬now🥰🥰🥰 Thanks again.
@keepersteam7339 Жыл бұрын
Thanks for this video. I learned.
@sirjohnl.langcuyan3505 Жыл бұрын
Ngayun may idea na ko lods. Salamat
@iskoteronggalaph69842 жыл бұрын
This video is very helpul and informative good content bro
@tabingtv8786 Жыл бұрын
Thank you❤️❤️❤️ for sharing and try to fix also
@marklicano19782 жыл бұрын
So smart to use plastic ties!
@emmanuelaleria11492 жыл бұрын
nice
@jongsbackyard Жыл бұрын
thanks for sharing kung paano mag assemble..
@dc.josebarbosa8412 Жыл бұрын
BOM TRABALHO. DEUS TE ABENÇOE GRANDEMENTE
@sitiosaocristovao265510 ай бұрын
Desejo muito sucesso pra você 🤝🙏
@sokehjayamerdeka7420Ай бұрын
Intinya dari pemasangan ada pada tang jepit dan tali tis kalo gak pake itu auto susah si Per dan pelat nya mental
@bossjtripmotv.52902 жыл бұрын
Galing mo nman sir
@joymadarcos1071 Жыл бұрын
Good job
@soctechtv
Жыл бұрын
Thanks
@terrycummings91958 ай бұрын
Thanks but you didn't install the black plastic piece before you put zip ties on, did you forget and have to start over?
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@joseguzman99042 ай бұрын
Brother cortaste el vídeo en el minuto 3:42 para mi es muy importante saber dónde y cómo va la pieza de plástico
@johnnyriches4276Ай бұрын
I am assembling the pressure switch but stumped with the black piece of plastic..you have it on the table and than it disappears
@johnnyriches4276
Ай бұрын
Not sure where it goes in the switch please help
@MarkJhunSumalinog Жыл бұрын
sir the small black plastic.where did you put it...
@bigbadhag
Жыл бұрын
It goes iside,its the little button on top you push down, that's the part that had me stumped
@JERKSTA213HOMES
Жыл бұрын
He edited because he fucked up he had to do it all over again
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@federicocabero97982 жыл бұрын
Sir may nabibili Po bang automatic adjuster Yung plastic Po Yun en nabasag kc Po Yung plastic adjuster
@soctechtv
2 жыл бұрын
Wala sir kuha ka na lng sa mga sirang unit o bile ka n lng ng bago
@carlnikolov Жыл бұрын
Damn music
@bhonbelmonte2695 Жыл бұрын
Where did put that black plastic???
@chrisjohnson6947
Жыл бұрын
Where did the black plastic piece go it just disappeared
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@AcesnEights698 Жыл бұрын
Yeah... that's something I hope to never do again. Many new curse words were invented.
@KaraokeTime-ec5rg13 күн бұрын
nakalimutan mo po ang itim una ilagay
@gerardosoria54097 ай бұрын
There is a little black part with 2 little sticks, u dont show up where go!!
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@jessemoore4061
3 ай бұрын
@@jerryayers7337thank you
@leroywallis25849 ай бұрын
where did the plastic peace go. most important part of the assemble
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@KaraokeTime-ec5rg13 күн бұрын
tanggal ka ulit kasi yung itim na nilalagay sa loob di mo inlagay
@nitsudgnilreps967010 ай бұрын
You forgot reset
@ginomanalo8155 Жыл бұрын
your still hiding u forgot to insert the plastic switch , such a crap assembling
Пікірлер: 96
Thank you so much for this video , I would have been screwed without it.
so, where does the black plastic piece go that seemed to disappear around 3:40...
@jamesdaul8540
Жыл бұрын
I think that should have been the first thing to go in!!!
@jameslandry9544
10 ай бұрын
Amen slight of hand but no help smh
@smittyschmid5457
4 ай бұрын
I came here to say the same thing. 😳
@jerryayers7337
3 ай бұрын
@@jamesdaul8540It slides in vertically and part of it stick out the top of the housing (reset button). Only goes in one way.
رااااااائعة رااااااائعة بزاااف يا اخي عزيز دائما تواصل معك يا احلى واجمل قناة 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
You have extra long screws to hold the switch to the plate. There's no room for the thickness of twist ties with the shorty screws on what I have. If you're watching the video it's obvious the plastic piece has to go in first and he had to take it apart to put it in. After multiple attempts using various methods, it was a thin wire that worked for holding things together and still being able to remove it. I also drilled a hole and wired the back end of the pressure plate. That's the critical part that always wants to pop out when you're trying to put it together. What a PITA I finally got it working like new. The problem was the gasket leaking air and now it doesn't.
I like how you cut the film and then put the plastic piece in that you forgot to put in in the beginning lil shady I didn't watch anymore🤨👎
@ethelbertjrtan7566
9 ай бұрын
😅😅😅
@aaahandy
5 ай бұрын
Did you catch him with his pants down?
@smittyschmid5457
4 ай бұрын
I came here for this same comment. 🤷🏼♂️
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Amazing video Have a Good time
L431 idol. maraming salamat sa pagbahagi ng iyong kaalaman at kakayahan, kabisado mo talaga lods
I could not get this switch back together without this video. Thank you for posting this!
@CaseyE-bn3vk
2 ай бұрын
I took mine apart and damn it went everywhere… couldn’t figure it out.. maybe this video will help.
Galing naman idol.thanks for sharing.God bless
L350 you are so very skilled hand ,sir. Good job❤
Great knowledge
Great video! Thanks os sharing. I have a very similar ressue switch that I need to put back together and this video should really help. One question though. There was a small plastic piece sitting next to the switch cover at 02:40, but not sure where did it go. I did not see you putting that piece in the assembly.
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@tanveernaeem1157
3 ай бұрын
Thank you so very much. Much appreciated.
Thank you for sharing po.
Nice sharing lods watching full
Good morning thanks idol for sharing this video stay connected
Nice sharing host , really you're expert in this mechanical electronics
Great tutorial, thank you for the knowledge you shared..👍 full watched... Have a wonderful day my friend
Great vedios
Magandang pagbabagi ng iyong video 🎉magandang panoorin hanggang sa wakas at para itoy suporta din nilang kaibigan
kailangan talaga marunong angg kabit ng ganyan buti nkita ko vedio mo maramong salamat
Again watching your video friend.nice sharing.❤❤❤
Watchiing kabayan..salamat sa pah share ng video
Assembly air compressor pressure switch , good
Hello sir watching replay here . Thank you for sharing this tutorial video. Thank you for sharing and visiting my house. Stay connected. God bless.
galing mo lods
thanks for sharibg lods
Thanks for your help! If it would have flew apart slower, maybe I'd seen where everything went!
Thank you so much for this video. I am fixing up a Craftsman air compressor and it has a very similar switch. Using the Vise Grips was genius!!
WOW so nice... Good job.... Thank you for sharing...
Lots of Thanks 🎉🎉🎉 I solved da problem 4m yo video. Thanks 👍👍👍
@soctechtv
10 ай бұрын
Welcome 👍
Informative, great tutorial! Job well done, keep on sharing your knowledge , ha e a great time, enjoy!
Thanks for sharing your ideas
Watching fullpack po
Galing lods thanks for sharing napaka husay ng pag kakagawa at napaka pulido ❤❤❤
2:58 you have the black plastic peice with the odd shape l. Where did you put that..
Good work assembled host ang galing
Nice lods galing....
Great help po. Thank you for sharing.
Wow nice sir
Salamat sa pagbahagi idol malaking tulong ito.. God bless mabuhay ka..
Eto yung nakatulong sakin ngayon. Maraming salamat po
Ayos Lodi nice content keep vlogging po god bless
Thank you for always sharing videos that give the audience a new perspective and true image of you and the place you want to convey. I am sure, you already have a loyal audience, including me, who love the authenticity of each video. Keep moving forward and work hard every day, I will always watch full videos with ads to support you
Thank you, I spent a lot of time trying to get this contraption together. Nearly drove myself nuts. Your technique solved the mystery for me. After taking this thing apart and ordering a new switch I realized it was just a simple reset button on the motor. I put it all back together following your technique and all works great. As one of your viewers noted the black plastic piece goes in Pryor to the spring attachment. Plastic ties and vise grips were the secret 👍 Have a backup pressure switch and thorough knowledge of what to do now. 🤬🤬🤬now🥰🥰🥰 Thanks again.
Thanks for this video. I learned.
Ngayun may idea na ko lods. Salamat
This video is very helpul and informative good content bro
Thank you❤️❤️❤️ for sharing and try to fix also
So smart to use plastic ties!
nice
thanks for sharing kung paano mag assemble..
BOM TRABALHO. DEUS TE ABENÇOE GRANDEMENTE
Desejo muito sucesso pra você 🤝🙏
Intinya dari pemasangan ada pada tang jepit dan tali tis kalo gak pake itu auto susah si Per dan pelat nya mental
Galing mo nman sir
Good job
@soctechtv
Жыл бұрын
Thanks
Thanks but you didn't install the black plastic piece before you put zip ties on, did you forget and have to start over?
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Brother cortaste el vídeo en el minuto 3:42 para mi es muy importante saber dónde y cómo va la pieza de plástico
I am assembling the pressure switch but stumped with the black piece of plastic..you have it on the table and than it disappears
@johnnyriches4276
Ай бұрын
Not sure where it goes in the switch please help
sir the small black plastic.where did you put it...
@bigbadhag
Жыл бұрын
It goes iside,its the little button on top you push down, that's the part that had me stumped
@JERKSTA213HOMES
Жыл бұрын
He edited because he fucked up he had to do it all over again
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Sir may nabibili Po bang automatic adjuster Yung plastic Po Yun en nabasag kc Po Yung plastic adjuster
@soctechtv
2 жыл бұрын
Wala sir kuha ka na lng sa mga sirang unit o bile ka n lng ng bago
Damn music
Where did put that black plastic???
@chrisjohnson6947
Жыл бұрын
Where did the black plastic piece go it just disappeared
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Yeah... that's something I hope to never do again. Many new curse words were invented.
nakalimutan mo po ang itim una ilagay
There is a little black part with 2 little sticks, u dont show up where go!!
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@jessemoore4061
3 ай бұрын
@@jerryayers7337thank you
where did the plastic peace go. most important part of the assemble
@jerryayers7337
3 ай бұрын
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
tanggal ka ulit kasi yung itim na nilalagay sa loob di mo inlagay
You forgot reset
your still hiding u forgot to insert the plastic switch , such a crap assembling
Neumíš to