How to Apply Tile Adhesive and Set Tiles Properly [Make Your Tiles More Durable]

Тәжірибелік нұсқаулар және стиль

How to install tiles the right way?
In this video, you will learn the NTCA-approved troweling techniques to apply tile adhesive and set tiles. This technique creates a stronger bond between the tile and the substrate. Prevent crack transmission, lippage, tile breakage, bulging or tenting, and other costly tile installation repairs.
Tiles are very durable materials that can last a lifetime - when the right tile adhesive and methodology was used. When tiles break, it is usually due to low-quality tile adhesive and faulty installation method.
The way you trowel mortar for setting tile makes a big difference. Tiles can withstand extra heavy service conditions. It takes a lot of impact or load to cause bond loss when installed correctly over a sound substrate.
On the other hand, unsupported spaces under the tiles create weak spots. Tiles with voids or air pockets underneath are easily damaged by heavy impacts, heavy loads, and other causes.
Spot bonding with mortar is also not recommended. It may be easier to set tiles this way, but it’s only a matter of time before the slightest force causes failure.
Today, many people are still using the wrong method in tile adhesive application and setting of tiles. They may get the job done more quickly, but they can’t get the proper mortar coverage and air gets trapped underneath the tiles, which ultimately leads to tile debonding.
Swirling the mortar causes voids where the tile is not bonded to the substrate. These voids can result in cracked tile and bond failure under normal use but especially under point load or impact.
Aside from impact and heavy loads, tiles with voids and poor mortar coverage are more likely to debond over a short period of time. According to the American National Standards Institute and the TCNA Handbook, a minimum of 80% mortar coverage is required for interior applications, and 95% for exteriors and wet environments.
The straight troweling method is the ANSI recommended technique in applying tile adhesive. In the latest episode of Magtanong Para Sigurado vlog, you will learn why it's the right way of applying tile adhesive.
If you have more questions, please leave a comment or message us through official Facebook page ( BuildritePhils)
You may also visit our website to learn more about our products and services (www.magnaprime.com.ph/)
Correction: 3:33 Notched Trowel Size recommendations have been updated. For 60x60 Tiles (12mm notched trowel). For 30x30 Tiles (6mm notched trowel).
#MagtanongParaSigurado #TileAdhesive #Tilesetting #TilesettersPhilippines #Tileinstallation #Tileadhesiveproduct #Tiles #Tilingsolutions #TilesPhilippines #Ceramictiles #Granitetiles #Tilingproject #Largetiles

Пікірлер: 296

  • @BUILDRITECONSTRUCTIONCHEMICALS
    @BUILDRITECONSTRUCTIONCHEMICALS Жыл бұрын

    UPDATE: 3:33 Notched Trowel Size recommendations have been updated. For 60x60 Tiles (12mm notched trowel). For 30x30 Tiles (6mm notched trowel).

  • @skr3163

    @skr3163

    Жыл бұрын

    Need pa po ba ng bonding agents or redflix bago gamitin to?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. For bare concrete applications, you just have to add water for Smartbond Flex. For tile over tile applications, we recommend to add cement grip. You can see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2275577692578014/

  • @darryramos9636

    @darryramos9636

    11 ай бұрын

    How about 40x40 tiles?

  • @leon_sanity

    @leon_sanity

    7 ай бұрын

    How bout naman pag 40×40 yung tiles sir. Ilan ho ang thickness dapat?

  • @jackiesoliveres3511

    @jackiesoliveres3511

    5 ай бұрын

    For tile over tile installation - Aside from the thin mortar, do we need to do back buttering for 60x60 tiles? Yung thin mortar, using the notched trowel 12 mm spaces, back buttering flat lang?

  • @davideliah7427
    @davideliah74272 жыл бұрын

    This is ABSOLUTELY legit information! Thank you very much! You are a big help specially sa mga first timer na kagaya ko! Mabuhay!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Thank you. Your comment is highly appreciated.

  • @Tingtvph9226
    @Tingtvph9226Ай бұрын

    Maraming Salamat sir. SA napaka-informative video method para SA tamang pag lagay Ng tiles.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Ай бұрын

    We appreciate your comment. Thank you for supporting Buildrite!

  • @trishamaniego4688
    @trishamaniego4688 Жыл бұрын

    Thank you for this. I will install tiles in our home soon. And I'll keep on watching your videos (i have subscribed too)

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    We appreciate your comment. Thank you for supporting Buildrite!

  • @jafire777
    @jafire7773 жыл бұрын

    Napaka informative talaga sir

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 жыл бұрын

    Hi Sir Jan ,thank you

  • @bogartlingayo7391
    @bogartlingayo7391 Жыл бұрын

    thank you for the info

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Youre welcome po sir.

  • @ViviNaval
    @ViviNaval Жыл бұрын

    Very informative video

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you so much for your support and your great feedback. Your kind words are greatly appreciated, and we hope you won't hesitate to let us know if we can serve you in the future.

  • @felixbalan5131
    @felixbalan51312 жыл бұрын

    Salamat sir sa kaalaman

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    You're welcome.

  • @thesjotile4752
    @thesjotile47522 жыл бұрын

    Base sa matalagal konang experience sa paggamit ng tile adhesive, ito ay isang malaking TAMA.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    We appreciate your comment. Thank you for supporting Buildrite!

  • @renatodanseco6246
    @renatodanseco62462 жыл бұрын

    Nice 👍

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    We appreciate your comment! Thank you for supporting Buildrite!

  • @arthuralcabaza1979
    @arthuralcabaza19793 жыл бұрын

    💯thank you very much!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 жыл бұрын

    You're welcome!

  • @Tan_Noah
    @Tan_Noah Жыл бұрын

    Nice

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Thank you for sharing your review with us. We are grateful for your kind words.

  • @melchorcabaluna1225
    @melchorcabaluna1225 Жыл бұрын

    Yan din gamit namin ditu sa japan

  • @spaceinvaders6189
    @spaceinvaders61893 жыл бұрын

    Do you conduct classes like tile setting, plastering, or how to apply floor epoxy for DIYers? Thank you :)

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 жыл бұрын

    Hi! You can message us through our official Facebook page facebook.com/BuildritePhils for us to assist you further regarding your query. Thank you

  • @kicksdown6995
    @kicksdown69953 жыл бұрын

    👍👍

  • @rafsdiychannel4875
    @rafsdiychannel48752 жыл бұрын

    salamat sir.. very informative. one question.. ano po pinaka recommended niyong tile spacing.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. The ideal tile spacing is 3mm to 5mm.

  • @marilougutierrez5227
    @marilougutierrez52272 жыл бұрын

    Mostly i heard that ABC tile adhesive is commonly used can you recommend also sir that brand thanks

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Good day! We do not have any idea which standard they used on their tile adhesive. We suggest to seek advice on its rightful manufacturer/distributor.

  • @raditodizon375
    @raditodizon37510 ай бұрын

    thanks for sharing. may video b kyo patungkol paginstall ng tile using dry pack?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    10 ай бұрын

    Hi, thank you for your inquiry. We do not recommend using a dry-pack method on tile installation.

  • @luckystrike656
    @luckystrike6563 жыл бұрын

    Hi Are you speaking one or two languages in this video? I hear English mixed with something I don't understand. Btw, great tips

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 жыл бұрын

    Hi! You can message us through our official Facebook page facebook.com/BuildritePhils for us to assist you further regarding your query. Thank you

  • @danilotingson5283
    @danilotingson52832 жыл бұрын

    sir gud day,sana po my vlog kau sa tile over tile at anong dapat gawen at gagamitin

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    We're currently making a video for this..Stay tuned in our page for the latest updates.

  • @zainfadhil2588
    @zainfadhil25883 ай бұрын

    Any recommendation for an indoor porcelain tile adhesive to be used on concrete slab with that has a tendency to bounce?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 ай бұрын

    Hi, thank you for your inquiry. What do you mean to "has a tendency to bounce"? Anong size din po ng tiles. Please message us on Facebook so we can discuss your inquiry: facebook.com/BuildritePhils

  • @zainfadhil2588

    @zainfadhil2588

    3 ай бұрын

    @BUILDRITECONSTRUCTIONCHEMICALS the location has a post tension slab, if for example you jumb on it the whole slab vibrates and shake!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 ай бұрын

    You can use Smartbond Flex Diamond C2TS2. It has an improved adhesion and flexibility.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 ай бұрын

    You can use Smartbond Flex Diamond C2TS2. It has an improved adhesion and flexibility.

  • @b2939161
    @b29391612 жыл бұрын

    Hi, do you recommended using tile levelers with this method po?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Yes you can use tile leveler to make your tile leveled.

  • @zenithsabando5416
    @zenithsabando541611 ай бұрын

    Area coverage/bag? Tnx!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    11 ай бұрын

    Hi, thank you for your inquiry. Smartbond flex tile adhesive can approximately covers 5m² at 3mm thickness.

  • @reynaldoagustin9181
    @reynaldoagustin9181 Жыл бұрын

    is 80% coverage of mortar same as wall tiles for interiors, samples on the video area on floor?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, Thank you for your inquiry! Yes, as long as same thickness.

  • @jeneferdutertedarcera7374

    @jeneferdutertedarcera7374

    Жыл бұрын

    Good morning Sir. Pwd po ba mag lagay ng floor tiles ng Cement lang ? Walang adhesive cement

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, we recommend using Buildrite Smartbond in tile installation. You can watch this video for your reference: kzread.info/dash/bejne/moOWpKOGZa7MeM4.html

  • @anitabenavides5548
    @anitabenavides5548 Жыл бұрын

    Hello, first time to see your video. Ganyan din po ba process pag marble ang flooring? Available na ba ang ganyang process nung 1996. Our house was constructed 1996 pa then years pass may mga nag crack na. Salamat innadvanced for your reply Sir!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thanks for sharing. For marble-type tiles, we recommend SmartBond Flex Gold for 60x60 cm and below, SmartBond Flex Diamond for 60x60 cm and large format tiles. Tile problems such as hollow sounds, popping, and cracks can be avoided by choosing the right tile adhesive and a proper tile application method. To help you more with your problem, please let us know your details through our Facebook messenger for us to set up an on-site visit in your area. We are more than glad to help you assess the actual condition of your tile problems so we can accurately recommend products and procedures for you. facebook.com/BuildritePhils

  • @rezanami7726
    @rezanami772615 күн бұрын

    Can directly tiles in cement flooring with only adhesive?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    15 күн бұрын

    Hi, thank you for your inquiry. Yes, pwede po. as long as walang existing sealer yung floor nyo.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    15 күн бұрын

    Hi. Thank you for your inquiry. Yes sir. Make sure lang malinis yung area.

  • @karamayuga3834
    @karamayuga38349 ай бұрын

    Ano dapat thickness ng adhesive sa concrete and sa tile? Ano dapat total thickness ng adhesive/mortar for interior tiles? Thank you for the informative vid

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    9 ай бұрын

    Hi, thank you for your inquiry. The thin-bed method in tiling installation can be achieved using the right size of notched trowel. You acn see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2245973822205068/

  • @fritzrespecia6353
    @fritzrespecia63532 жыл бұрын

    May ibat ibang klase kasi na tile's

  • @jesiebacnaon9835
    @jesiebacnaon98353 ай бұрын

    Sir vlog po kau ng 2 kind of mixing smartbond

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 ай бұрын

    Hi, thank you for your suggestion! We will surely consider this.

  • @xtiangelalnucap97
    @xtiangelalnucap972 жыл бұрын

    Hi. Pag 60x60cm homogeneous tiles po, same lang po ba ng pag install gaya sa porcelain tiles? Thanks

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. Yes, same as you seen on this video.

  • @ulysseslayuganjr6054
    @ulysseslayuganjr60542 жыл бұрын

    Sa dry pack method po sir, need pa po ba gamitan ng trowel ang adhessive tulad po dyan sa demo nio? Thanks.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. Thick bed method is a traditional way of installing tiles, which is already outdated. It's the process of applying drypack or tile adhesive with a thickness of 15mm to 25mm to install the tiles. This method has many disadvantages: - It is time-consuming because of the preparation - It cannot meet the required mortar coverage under the tiles - It is costly because it requires more material consumption - It requires very skilled workers to avoid installation failure We recommend applying a topping first using Cement grip and Hardcrete 310 prior to installing tiles to correct the floor level, then use the same technique as seen on this video. Here is the link for Cement grip and Hardcrete 310: kzread.info/dash/bejne/ZIKYuqqfhMa0gMY.html

  • @kingsantos7270
    @kingsantos72702 жыл бұрын

    good day sir, ask ko lang po na need po ba na sinsilin ang makinis na floor bago itiles? pwede po ba haluan ng fined sand ang adhesive kahit na ang taas ay 3.5 cm. po ang lalagyan? salamat po sa inyong video it helps a lot.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. There is no need to chip the surface prior to the installation of tiles. You can use Buildrite's Cement grip as tile adhesive enhancer. You can see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2366935676775548/ We also do not advice mixing sand and cement on tile adhesive because it will affect the quality of the adhesive. You can use Buildrite's Cement grip and Hardcrete 310 as concrete topping then use the thin bed method on installling your tiles. You can watch this video for your reference: kzread.info/dash/bejne/ZIKYuqqfhMa0gMY.html

  • @arielestrada7077
    @arielestrada707719 күн бұрын

    Boss pde po bang gamitin yang pang plastering sa crack cement na slab

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    19 күн бұрын

    Hi, thank you for your inquiry. Hindi po, sir. pa-send po ng actual photo ng area sa official facebook page namin na facebook.com/BuildritePhils

  • @histalyterrayo425
    @histalyterrayo425 Жыл бұрын

    Sir thank you sa reply mo tanong uli sir ang adhesive ba hahaluan parin ng buhangin

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. Katulad ng sagot sa una ninyong katanungan, Hindi, dahil makakabawas sa performance ng adhesion promoters nito per volume of mortar na nilalagay sa tiles. Just add water lang po.

  • @deannarentegrado7169
    @deannarentegrado71693 жыл бұрын

    Hello po. Pano po direction ng troweling pag 40x40 or square tiles po?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    3 жыл бұрын

    Hi Maam /Sir regarding your query, straight application po

  • @jasperbutin1984
    @jasperbutin1984 Жыл бұрын

    sir, may video po ba kayo ng agkabit ng tiles sa makinis na sahig? sabi daw kase ng naggagawa samen di na daw pwede lagyan ng tiles ang makinis na sahig.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for your inquiry. We do not have video for that yet. However, you can still install tiles on a smooth finish flooring using the same method on this video. We recommend Buildrite's Smartbond C2S1 as your tile adhesive. You can watch this video for your reference: kzread.info/dash/bejne/eZuTxcuTYanFd5c.html

  • @loujeancerial4669
    @loujeancerial46692 жыл бұрын

    nice sir. ask lang po? pwede ba na tile adjesive lang ang gamitin? para sa tiles at sa flor? 1,5mm lang kasi ang allowance ng door namin sa flor. salamat po. from dumaguete po.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. Yes, tile adhesive is applied directly on your substrate when installing tiles.

  • @roncesquejano1173
    @roncesquejano11732 жыл бұрын

    Hello poh sir ,Oki lang poh bah patungan ng granite tiles ang lumang pangkaraniwang tiles ja naka install dati pa?thanks poh

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. Yes, you can install new tiles on existing tiles. You just have to use Buildrite's Cement grip as your tile adhesive enhancer. You can see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2275577692578014/

  • @adrianvalencia2119
    @adrianvalencia21192 жыл бұрын

    sir pwede po ba ang pure cement sa pag nag tiles sa walling,60 X 60 po ang tiles

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. It's better to use pure Smartbond Lightweight Tile Adhesive in installing tiles because it has a high bonding strength than sand and cement mix for tile installation.

  • @Annikev14
    @Annikev142 жыл бұрын

    Hello Sir. Thank you sir. Very informative. Ask ko lang rin po.. Nagpapagawa kami ng bathroom using 60x120cm porcelain tiles (wall to wall), kaso sa application ng foreman namin, may halo po na tile adhesive and cement ang ginawa niya and wala po siyang gamit na trowel tool nor may ridges sa tile adhesive application niya, as in he lays the adhesive flat on the wall then tska po ilalagay ang malaking tiles. Acceptable application po ba iyon? Hindi po ba malalaglag ang tiles over the years? Thank you.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. In this case, 1) we do not recommend mixing tile adhesive and cement, 2) the right trowel should be used when installing tiles, 3) the right tile adhesive rating should be used.

  • @Annikev14

    @Annikev14

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS Thanks for the advise sir. I’ll rely this to our foreman. More power to your channel and business. Thank you.🤩

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Thank you.

  • @darwinfajardo4702

    @darwinfajardo4702

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS Hi! May I know po kung bakit di pwede paghaluin ang tile adhesive and cement? Yun kasi ang ina-advise ng isang tile setter ko. Anong cons po nun? Thank you in advance.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Good day! Ang paghalo ng semento sa tile adhesive ay makakabawas sa performance ng adhesion promoters nito per volume of mortar na nilalagay sa tiles. Kapag nangyari ito, hihina ang kapit ng tile adhesive na magreresulta sa tile debonding o KAPAK.

  • @histalyterrayo425
    @histalyterrayo425 Жыл бұрын

    Kailangan bang haluan ng portland cement ang adhesive

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. HINDI. Ang paghalo ng semento sa tile adhesive ay makakabawas sa performance ng adhesion promoters nito per volume of mortar na nilalagay sa tiles. Kapag nangyari ito, hihina ang kapit ng tile adhesive na magreresulta sa tile debonding o KAPAK. Watch this video to learn more: kzread.info/dash/bejne/eZuTxcuTYanFd5c.html

  • @onaddosama
    @onaddosama Жыл бұрын

    Hi. What can you say about the dry pack method of installing tiles? Ito kasi ang majority na method na ginagawa hanggang ngayon. Ano po ang advantage at mga disadvantages nito? TIA sa sagot.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, Thank you for your inquiry. In this video you will know the full details regarding your question, kindly watch this video for your reference: kzread.info/dash/bejne/eZuTxcuTYanFd5c.html

  • @ruthgarcartagena8993
    @ruthgarcartagena89932 жыл бұрын

    Hi po. If gagamit po ng sand and cement mixture sa tiles ng hagdan po ano po ba ang correct mixture?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    If you're still using the dry pack method, we recommend at least using a high-strength tile adhesive additive/adhesion promoter to improve the adhesion strength of your mortar mix. Here's how you can do it: 1. Mix 1 bag Portland cement and 90kg of sieved sand. 2. Add 250 grams of Buildrite TILE GRIP to the mixture before adding water. Mix it with a mechanical until a homogenous and lump-free paste is obtained. 3. Allow the mixture to sit for 5 minutes before stirring again. The mixture will yield 5.2 (25kg) bags of high-strength tile adhesive. TILE GRIP is a powder tile adhesive additive specially formulated to be mixed with cement and sieved sand to produce a high-strength tile adhesive for ceramic tiles. Click on the link below to see details. web.facebook.com/BuildritePhils/photos/a.256515081150962/2417525031716612/?__cft__[0]=AZWZ2eCFmoELeHCErg92lM5f400O8rYAAtlHQZH0L-eTnI0Im9sKZnQir_0GJQ0JZ0gJNA_TFliDIDn36ZLUn6_PAGRZMLPrq32tCZQGFiR15NDSJ3ngeN3cRT3FpVgVpv0&__tn__=EH-R

  • @dennismendoza4208
    @dennismendoza42082 жыл бұрын

    Sir napansin ko na hindi dumidikit ang ashesive sa synthetic granite tiles pero sa ceramics dumidikit ng ayus may ibang product adhesive ba for synthetiic and porcelain tiles.? Tanx

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. For synthetic granite tiles, we recommend to use Buildrite Granite Polymer C2 for flooring and Buildrite Smartbond Lightweight tile adhesive C2S1 for walls. For Porcelain tiles, you can use Buildrite Smartbond Lightweight tile adhesive C2 for flooring and Buildrite Smartbond Lightweight tile adhesive C2S1 for walls. You can watch this video for your reference on how to choose the correct tile adhesive: kzread.info/dash/bejne/d2iMlMNuXdivnrg.html

  • @joyrennmustajotan3388
    @joyrennmustajotan3388 Жыл бұрын

    👏🏾👏🏾👏🏾💯💯💯👆🏽👆🏽👆🏽

  • @ArtRob22
    @ArtRob22 Жыл бұрын

    thank you po sa tips. ask ko lang po if I have an existing tiles same lang po ba ang technique if we choose na ipapatong nalang po yung bagong tiles or granite?? what type of adhesive ang ma-recommend nyo sa gamitin namin if papatong lang po sa existing tiles?? thanks po!!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. Proper assessment and surface preparation are needed for this method. You can use Buildrite Cement grip as a tile adhesive enhancer for tile over tile applications. You can see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2275577692578014/

  • @ArtRob22

    @ArtRob22

    Жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS thank you po sa reply and for the instructions. more power to your brand po!!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Youre welcome po.

  • @jenxu2718
    @jenxu2718 Жыл бұрын

    Sir pede po ba na pang finishing din ang adhesive sa pader kase sayang po ung natira na adhesive,slmat po sa sasagot

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. No, tile adhesive requires a thinner application while plasters requires a minimum of 10mm thickness. We recommend Plasterlite for plastering. You can see this post for your reference: facebook.com/BuildritePhils/photos/pb.100076193444241.-2207520000./2537411649727949/?type=3

  • @ronilogulpan7715
    @ronilogulpan7715 Жыл бұрын

    good afternoon sir,kailangan oo ba ibabad sa tubig ang ceramic tile bago ikabit?slmt po.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. Choose a tile adhesive that has excellent water-retention capability to hold its water content during the curing process. With this, you can eliminate the need to soak tiles in water, which saves time and prevents tile debonding. The pores on tiles can absorb the water from the tile adhesive, resulting in early dehydration and poor adhesion. You can see this post for your reference: facebook.com/BuildritePhils/photos/a.256515081150962/2249120405223743/

  • @arlenroquino5057
    @arlenroquino50572 жыл бұрын

    Good pm po sir..pwede po ba magtiles na purong adhessive lng na walang sand and cement na halo..thank u po

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    For using Smartbond Lightweight Tile Adhesive, we only recommend to mix it with water no need to add sand and cement.

  • @richardsabino9190
    @richardsabino91902 жыл бұрын

    Pede po ba ang pure adhesive Kay sa mix ng dry pack?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    It's better to use pure Smartbond Lightweight Tile Adhesive in installing tiles because it has a high bonding strength than sand and cement mix for tile installation.

  • @mzkariah11
    @mzkariah112 жыл бұрын

    Thank you very informative, tanong lang po sana ako mas standard po ba gamitin ang pure adhesive kesa sa tinatawag nilang dry pack?thank you po yan kasi sabi ng sitter sa akin magpa tiles po kase ako

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    For tile installation it is recommended to use pure tile adhesive. Once you add any additional cement it may affect the adhesion of your tile adhesive. Please click on the link below to see video. studio.kzread.infoGg_ciZ1F_G4/edit?c=UCOW4xyTyGGxrMfbPgrpzfhg

  • @amboymanzano6964

    @amboymanzano6964

    2 жыл бұрын

    sir pano if 2 to 3 inches ung dapat kapal Ng lalagyan Ng tiles? at costly pra sa pure adhesive, ano ma rerecomentd nyo?

  • @amboymanzano6964

    @amboymanzano6964

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS sir pano if 2 to 3 inches ung lalagyan Ng tiles and costly naman pra sa pure adhesive. ano recommend nyo?

  • @sgtpepperking

    @sgtpepperking

    2 жыл бұрын

    @@amboymanzano6964 buhosan niyo muna ng mortar tapos ibara niyo dapat leveled tapos hintayin niyo 1week or more then layout tiles using pure adhesive with correct size notch trowel.

  • @victoryap7044
    @victoryap7044Ай бұрын

    Pwede po magpatong ng new tiles sa old existing tiles ano po pwede gamitin at procedure using buildrite product sa open deck terrace po lalagyan,salmt sa pagreply

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Ай бұрын

    Hi, thank you for your inquiry. Yes, it can be done. However, you have to consider checking if the existing tiles are still intact. You can use Smartbond flex tile adhesive depending on the types and size of your tiles and Buildrite Cement grip. You can see this post for your reference: facebook.com/photo/?fbid=413010887915356&set=a.184760590740388

  • @victoryap7044

    @victoryap7044

    Ай бұрын

    Direct ko pong iaapply Ang cement grip sa old tiles Bago patungan ng buildrite tiles adhesive

  • @victoryap7044

    @victoryap7044

    Ай бұрын

    Iyong side po wall n lalagyan ng tiles ano pwede ilagy n water proofing

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Ай бұрын

    In order to fully answer your question. Please message us on our Facebook page so we can discuss your inquiry: facebook.com/BuildritePhils

  • @roncesquejano1173
    @roncesquejano11732 жыл бұрын

    ask ko lng poh pede poh bang haluan ng semento ang adhesive?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi.Thank you for your inquiry. No need to add cement. You just need to add water on tile adhesive.

  • @andrewfields5607
    @andrewfields5607 Жыл бұрын

    Matapos pong malagyan ng hinalong cement at sand ang flooring, Ang tile adhesive po ba ay iniaaply/ipinapahid ng puro sa tiles at yon ang lialagay sa mixed cement & sands sa flooring o imimix din sa cement, sands?? Tanx po

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi.Thank you for your inquiry.Yes po sir mas maganda puro po yung tile adhesive na i apply sa tiles at flooring.You can watch this video for your reference. kzread.info/dash/bejne/kYt9qKOsgpOambA.html

  • @chibinco5765
    @chibinco576510 ай бұрын

    Hi Sir Derrick, paano ung 95percent mortar coverage? Thank you very much.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    10 ай бұрын

    Hi, thank you for your inquiry. Sundin nyo po yung process sa video using notched trowel pang apply ng tile adhesive using thin bed method.

  • @robertanthonyflores6293
    @robertanthonyflores62938 ай бұрын

    Need ba basain ang porcelain tiles, salamat sa sasagot

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    8 ай бұрын

    Good day! Hindi na po kailangang basa-basain ang tiles, sir.

  • @robertanthonyflores6293

    @robertanthonyflores6293

    8 ай бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS hi thanks for the response sir, kht ceramic tiles? Ksi mas porous?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    8 ай бұрын

    Traditionally, tiles are soaked in water to prevent it from absorbing water from the tile adhesive. The pores on tiles can absorb the water from the tile adhesive, resulting in early dehydration and poor adhesion. Therefore, you have to choose a tile adhesive that has excellent water-retention capability to hold its water content during the curing process. With this, you can eliminate the need to soak tiles on water, which saves time and prevents tile debonding. For this, we recommend SmartBond Tile Adhesive, a ready-to-use, cement-based tile adhesive created to properly bond most types of tiles for indoor and outdoor installation. It has excellent water retention to prevent the absorption of water into the dry tiles or substrate. facebook.com/BuildritePhils/photos/a.256515081150962/2249120405223743/

  • @nervinpanganiban2075
    @nervinpanganiban20752 жыл бұрын

    Sir ano po bang adhesive pwd sa tyles at plywood.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi .Thank you for your inquiry .We recommend handy fix to tiles and plywood . Apply to one surface and press together the substrates. Hold until it sets before releasing.

  • @nstchannel9525
    @nstchannel95252 жыл бұрын

    pwede po ba pure adhesive n lang ang gamitin,,hindi na gamitan ng buhangin at cement ang flooring

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    We recommend not to add sand and cement for Smartbond Tile Adhesive. It may affect the adhesion and flexibility of your tile adhesive and may result to delamination.

  • @jonassharma1
    @jonassharma16 ай бұрын

    Hello po. We have ceramic tiles na 30x 30 at 40x 40. Kindly advise what best smartbond or tile adhesive type to use please. Thank you po.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    6 ай бұрын

    Hi.Thank you for your inquiry.For 30X30 tiles pwede po kayo gumamit ng Smartbond Flex Silver.

  • @jonassharma1

    @jonassharma1

    6 ай бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS Maraming salamat po!

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    6 ай бұрын

    You're welcome po.

  • @kahilom7283
    @kahilom7283Ай бұрын

    Sir pire tilde adhesive lang po ba gamitin wla na cement na ihahalo

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Ай бұрын

    Hi.Thank you for your inquiry. Yes sir pure adhesive po.Not advisable haluan ng cement.Just add 7 liters of water.

  • @maberikinstink9407
    @maberikinstink94072 жыл бұрын

    Hello po, ok lang po ba ang tile adhesive na 2 inches thick ang pagkalatag para hindi na gagamit ng dry pack mortar?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    To get the right elevation of your floor for tile installation you can use Hardcrete 310. Hardcrete 310 has a compressive strength of 3000psi @ 10mm Thickness. Please click on the link below to see video. Thank you. facebook.com/BuildritePhils/videos/104616120924

  • @johnerrolalfonso2312
    @johnerrolalfonso23122 жыл бұрын

    Kailan po ginagamit ang back buttering?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. Back buttering usually used on bigger size of tiles to achieve good mortar coverage and good adhesion specially if there is warpage present.

  • @adrianvalencia2119
    @adrianvalencia21192 жыл бұрын

    pwede kya paghaluin ang purong cement at adhessive

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. No sir because its better to use pure adhesive to use for good adhesion

  • @rodrigobayan8542
    @rodrigobayan85422 жыл бұрын

    Sir ask ko lng po kng San pwedengag inquir about sa tile adhesive at buy ndin ako

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Good day! You can order online via our Magna Prime Shop (bit.ly/3D8vqLx) or our Lazada and Shopee shop or buy from our partner depots near you (bit.ly/3mo43WZ)

  • @davideliah7427
    @davideliah74272 жыл бұрын

    Tanong ko lang sir, kapag ceramic tiles kailangan po bang ibabad sa tubig ng ilang hrs? Or pahiran nlng ng basahan bago ikabet?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    No need to soak your tiles since it has a Good Water Retention properties. It gives you more time to set your tiles properly.

  • @warlitomalamnao2682
    @warlitomalamnao26822 жыл бұрын

    Pwede Po bang haluan ng buhangin Ang adhesive Sir?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    We do not recommend to add cement the tile adhesive. It may affect the adhesion of your tile adhesive.

  • @junieflorruaza919
    @junieflorruaza9192 жыл бұрын

    Asking paano at ano ang gagamitin pag mag repair na ng tiles na hindi na kumapit at paano ang paraan

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    for delaminated tiles you need to remove and replace and use the proper tile adhesive. Selection of tile adhesive depends on the type of your tiles and the area of application. Click on the link below to see details. Thank you. studio.kzread.infoGg_ciZ1F_G4/comments?c=UCOW4xyTyGGxrMfbPgrpzfhg

  • @jaygarcia9368
    @jaygarcia93682 жыл бұрын

    good day po my tanong po ako pag adesive c1s1 po ggmitin sa tiles no need na po ba cemento . pwde na po ba i directa yung adesive sa tile at i install?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    No need to mix with cement. Mix only with 6.5-7L of water per bag. Mixing with additional cement may affect the performance of Smartbond Lightweight Tile Adhesive.

  • @janpat2466
    @janpat2466 Жыл бұрын

    Ask ko lang sir d na ba yan hahaluan pa ng cement yang adhsive? O purong adhsive kahit sa wall

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi.Thank you for your inqury.Yes po sir clean water lang po ihahalo.

  • @tomorai8056
    @tomorai805610 ай бұрын

    Pwde ko ba direct gamitin tile adhesive sa newly painted roofdeck/floor cementious waterproof painted, applying tile adhesive on floor then back of the tiles ano po ba needed maliban sa tile adhesive.... Mas like ko gawin tile adhesive compared sa dry pack na old tradition Any advice for cementious painted floor paano mag tile setting

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    10 ай бұрын

    Hi, thank you for your inquiry. Please message us on our Facebook page so we can discuss your inquiry: facebook.com/BuildritePhils

  • @rodrigobayan8542
    @rodrigobayan85422 жыл бұрын

    Good pm po San po kyo may branch dto sa cabanatuan

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Good day! You can order online via our Magna Prime Shop (bit.ly/3D8vqLx) or our Lazada and Shopee shop or buy from our partner depots near you (bit.ly/3mo43WZ)

  • @kahilom7283
    @kahilom7283Ай бұрын

    Sir pure tile adhesive lang po ba gagamitin pag istall ng tiles oh hahaluan pa ng cement

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Ай бұрын

    Hi.Thank you for your inquiry. Yes sir pure adhesive po.Not advisable haluan ng cement.Just add 7 liters of water.

  • @jeffreypalero9647
    @jeffreypalero9647 Жыл бұрын

    Sir ano po masasabi nyo about Sa dry packing method Ng tiles

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. We recommend to use screed to level your flooring first before using the thin bed method application of tile adhesive. We do not recommend using the dry pack method.

  • @carllesterremorin6744
    @carllesterremorin67442 жыл бұрын

    panu naman po sa repairing ng mga umangat/na basag na tiles?my video den po ba?pwede bang adhesive na lang?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. For repairing debonded tiles, you can use Max Bond All Purpose Epoxy or Non-Sag Epoxy. You can see this post for your reference: facebook.com/maxbondadhesivesolutions/posts/2894288690606721

  • @carllesterremorin6744

    @carllesterremorin6744

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS morethan 10 tiles po yung umangat eh..okay lang po ba yan?

  • @doceric4271
    @doceric4271 Жыл бұрын

    Review den Redifix ano yan?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Good day! Unfortunately, we do not have idea on other brands. We suggest to seek advice to the rightfull manufacturer/distributor.

  • @Cris-kx5dc
    @Cris-kx5dc11 ай бұрын

    good day! question po. 4 po nag popup na tiles namin sa first floor. since buo p naman po, pede po bang idikit n lang ulit ung dating tiles (60x60)?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    11 ай бұрын

    Hi.Thank you for your inquiry.Kapag ganyan po sir kapak na po yan.Remove and replace na po ng tiles.

  • @rubymagdaug2441
    @rubymagdaug24412 жыл бұрын

    Ask ko lang can i use only tile adhesive sa pag lagay ng pieces ng broken terrracota sa cemented wall?of not what's the mixture? THANKS

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    For wall decorative stones you can use Smartbond C2S1. It is suitable for wall applications because it has an improved adhesion and flexibility. Please click on the link below for details. Thank you. studio.kzread.infoGg_ciZ1F_G4/edit?c=UCOW4xyTyGGxrMfbPgrpzfhg

  • @rubymagdaug2441

    @rubymagdaug2441

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS nagpagawa ako ng mga plant boxes around sa fruit bearing trees sa back yard namin today.Planning to make use of our broken paso (clay pots )at yung mga retaso ng mga ceramic outdoor tiles sa terrace.Ipapalagay ko sana sa palibot ng plant boxes scattered hindi dikit dikit ang pagdikit ng mga ito.Can I use the Smartbond C2S1 na sinasabi mo.Do I have to use it purely or with cement mixture?(Refer to manufacturers guide?) Had watched the link you shared t but wants still to be sure.Many thanks .God bless.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Yes, for outdoor applications we recommend Smartbond C2S1. We do not recommend mixing it with cement.

  • @rubymagdaug2441

    @rubymagdaug2441

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS Sa Handyman /Ace Hardware lang ba nakakabili ng Smartbond C2S1?Tried sa nearby hardwares here in our place pero not available?Any idea how it looks like per gallon ba ito o powder in consistency?Is this expensive any idea of the price?Thank you again

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Good day! You can order online via our Magna Prime Shop (bit.ly/3D8vqLx) or our Lazada and Shopee shop or buy from our partner depots near you (bit.ly/3mo43WZ)

  • @yanghael
    @yanghael2 жыл бұрын

    Hello po, ask ko lng po sa pagtitiles po ba isisisi pag may tumatgas na tubig, lalo na pag sinilsil?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi Maam /Sir Marami po possible reason,Possible na damage yung waterproofing habang nagtatiles

  • @yanghael

    @yanghael

    2 жыл бұрын

    Sir panu yun, eh isang buwan na tpos ang pagtitiles ska sinisil, tas binaklas tas sinabing d natuyo yung simento,

  • @fritzrespecia6353
    @fritzrespecia63532 жыл бұрын

    Ano Po ba dapat quality ng tile's sa floor,

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    There are tiles that are intended for floor application and wall application. Most of floor tiles is thicker than the usual and has a darker bottom part. Use the appropriate tiles depending on the manufacturers specification and chose the right tile adhesive depending on the area of application and the type of tiles. Please click on the link below to know more. Thank you. studio.kzread.infoGg_ciZ1F_G4/edit?c=UCOW4xyTyGGxrMfbPgrpzfhg

  • @prody2060
    @prody2060 Жыл бұрын

    Sir almost 1 yr na yung flooring nagayun ko lagyan ng tiles. Kailangan ko paba mag lagay ng wiremesh para pampatibay or hindi na kailangan?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. No need to use wiremesh for concrete flooring tile installation. We recommend using na correct tile adhesive depends on the size of your tiles and use the same method of application as seen on this video. You can watch this video to now more on how to choose the correct tile adhesive: kzread.info/dash/bejne/moOWpKOGZa7MeM4.html

  • @DanDan-li4hr
    @DanDan-li4hr Жыл бұрын

    ok din ba gumamit ng electric tile vibration tool. Sa wall tile same technique din ba? legit din ba yung buildright product sa shopee

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi, thank you for your inquiry. Yes, you can do the same technique using that method. Here is our official Shopee shop link: shopee.ph/buildrite_official

  • @jhonnydiamse4020
    @jhonnydiamse4020 Жыл бұрын

    Ano po maganda gamitin ceramic tile na adhesive nagakaroon kc ng kapak ung mga tiles ko sa sala, tinanggal ko na, para di ko na tiktikin ung cemento o kaya grind kc maalikabok ung magandang pandikit na lng sana ung madalian lng.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for inquiry. Kapag ganyang case na po mas maganda po remove and replace na. Kasi unti unti narin po yan mag aangatan lalo pa't kapak na po.Thank you.

  • @simpledonut7484
    @simpledonut748410 ай бұрын

    Hi. Paano ba tamang pag keep ng used tile adhesive? Madalas kask nasasayang lang, namumuo gaya ng sa semento.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    10 ай бұрын

    Hi.Thank you for your inquiry.I sealed lang po mabuti sir.

  • @chinoakim8191
    @chinoakim8191 Жыл бұрын

    Sir paano ho if ang flooring para latagan ng tiles ay smooth finished cya? Ay ano ang tamang method sa pag tiling?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for your inquiry. 7 TIPS ON HOW TO USE THE TILE ADHESIVE PROPERLY. 1. DO NOT USE EXCESSIVE AMOUNT OF WATER IN MIXING THE TILE ADHESIVE. Excessive amount of water when mixing the tile adhesive is one of the cause of tile debonding. The level of water added onto tile adhesive will significantly affect its adhesion strength. Tile installer must be carefully read the mixing ratio and methodology to prevent tile debonding. 2. CLEAN THE SURFACE BEFORE INSTALLATION OF TILES TO PREVENT TILE DEBONDING. Unprepared and improper cleaning of the surface before tile installation will not let the tile adhesive bond to the substrate, and it will cause tile debonding in the future. Surface must be clean from any dirt and dust before the installation of tiles to prevent tile debonding. 3. USE SUITABLE EQUIPMENT AND MATERIALS IN APPLYING TILE ADHESIVE TO ACHIEVE BEST RESULTS. Unskilled tile setter, unsuitable equipment and materials, and lack of project management are just a few things that can lead to poor workmanship. Quality work begins with the conscious efforts of tile setter to execute the specifications of the contract, he is responsible for meeting standards of quality, care, and expertise. 4. NO NEED TO SOAK TILES ON WATER. Tiles have pores will absorb the water out of the mortar without allowing it to set properly, leaving weak bonds between mortar and tile. But using a tile adhesive that conforms to European standard like Buildrite Smartbond tile adhesive, there is no need to soak the tiles on water because of its water retention capability, it also prevents hollowing, shedding, or even cracks on your tile adhesive. 5. USE THE RIGHT SIZE OF NOTCHED TROWEL. No matter how much mortar piled onto the trowel, the notches apply it in nice, even lines of identical thickness. It creates spaces between the lines of mortar. These allow air to escape when the tile is pressed into the mortar. Without the spaces, you could get air pockets that prevent the tile from lying flat or adhering properly and will lead to tile debonding. Three commonly used trowel sizes are: 3mm x 3mm Square notch trowel for 30cm x 30cm and below size of tiles. 6mm x 6mm Square notch trowel for 60cm x 60cm and below size of tiles. 10mm x 10mm Square notch trowel for 60cm x 60cm and above size of tiles. For large format tiles, back buttering is recommended to apply enough supporting adhesive under them. 6. DON'T RUSH THE CURING TIME. Even though all the tiles are down on the floor and set, don't start putting the grout down. Allow the thin-set the proper amount of time to dry, otherwise you will damage the tiling job.Once tiling is complete, do not disturb for at least 4 hours. Wait 24 hours after grouting before opening the area to dry service and 7 days for wet service. 7. KNOW THE RIGHT TILE ADHESIVE TO USE. On the Philippine market today, there is no standard on what tile adhesive to use on a specific tile application resulting to tiling failure.According to the European standard BS EN 12004; C1 and C2 ratings are the requirements for cementitious tile adhesive while S1 and S2 ratings are the requirements for deformable tile adhesive. This classification will determine the correct and suitable tile adhesive for each type of tiles and application. The size and type of tiles will decide what level of C rated tile adhesive to use while the floor elevation, indoor and outdoor area of application and floor and wall application decides the level of S rated tile adhesive to use on the tiling.

  • @rupertodavidjr.9025
    @rupertodavidjr.90252 жыл бұрын

    Pno po pg aaply kung dry pack ang gamit.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Good day! Sorry, but we do not recommend using dry pack on installation of tiles.

  • @NeilSalumbides09
    @NeilSalumbides09 Жыл бұрын

    hindi napo ba kailangan yung dry pack pag sa floor? rekta tile adhesive napo kaagad? thanks po sa advice. 🙏

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for your inquiry.Yes po maam, no need na po drypack.

  • @NeilSalumbides09

    @NeilSalumbides09

    Жыл бұрын

    sa lazada lang po ba available yung product?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Good day! You can order online via our Magna Prime Shop (bit.ly/3D8vqLx) or our official Lazada and Shopee shop (s.lazada.com.ph/s.fFwNe) or buy from our partner depots near you (bit.ly/3PKbnZW)

  • @adrianvalencia2119
    @adrianvalencia21192 жыл бұрын

    sir,im beginer for installing tiles,alin po ba ang dapat unahin na na lagyan ng tiles Walling or flooring sa ,CR po at Banyo thanks po

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi sir, much better po if mauna ang wall tiles bago po ang floor tiles, sa ganoong paraan naiiwasan po ang pagtapon ng mga tira tirang adhesive sa floor tiles

  • @adrianvalencia2119

    @adrianvalencia2119

    2 жыл бұрын

    thank you po

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    You're welcome.

  • @arnelmercado465
    @arnelmercado465 Жыл бұрын

    Sir tanong ko LNG po kung ilang semento any mggamit s 30 PCs n 60x60 ntiles s dry pack method slam at po

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for your inquiry. We do not recommend using dry pack when installing tiles.We recommend to apply a concrete topping first prior to the installation of tiles to avoid using the thick bed method For 60x60 porcelain tiles, we recommend Buildrite's Smartbond C2S1. You can watch this video for your reference: kzread.info/dash/bejne/n6Fp0Y-TgpSdZZc.html

  • @ligerzero6518
    @ligerzero65182 жыл бұрын

    Sir pwede bang tile adhesive lng wala ng dry pack ? Naka rough po yung flooring.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    No need for dry pack if you already have a leveled floor. To get the right elevation of your floor you can use Hardcrete 310. Please click on the link below on how to apply Hardcrete 310. kzread.info/dash/bejne/X2qbl7aHoMbehdY.html

  • @silvinotorres5765
    @silvinotorres57652 ай бұрын

    Sir. Tanong kolang kung anong magandang gamitin na materyales sa pag repair ng floor tiles umaangat na po kc. Pero hindi pa naman totaly na nabakbak. Nag aangatn

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 ай бұрын

    Hi, thank you for your inquiry. You can use Handy fix. However, you have to remove the tiles then reapply using Handy fix. You can see this post for your reference: facebook.com/photo/?fbid=371708838712228&set=a.184760584073722

  • @aaronfernandopabuayon7687
    @aaronfernandopabuayon76872 жыл бұрын

    Ayus lang po ba na purong adhesive ang gagamitin kahit wala ng dry pack.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Yes, we recommend applying only tile adhesive using the thin bed method as seen on this video.

  • @robinmacaraeg5755
    @robinmacaraeg57555 ай бұрын

    Anu size ng notched trowel sa 30/60 na tiles po..slamt

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    5 ай бұрын

    Hi. Thank you for your inquiry. 10 mm po sir.

  • @jamaluddinlakibul4200
    @jamaluddinlakibul42002 жыл бұрын

    Boss ano ang Mas matibay Para sa 60x60 porcelain tiles, gumamit NG dry pack or pure mixture? Kung mixture naman saan mas matibay adhesive or cement?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. We do not receommend using dry pack when installing tiles. For 60x60 porcelain tiles, we recommend Buildrite's Smartbond C2S1. You can watch this video for your reference: kzread.info/dash/bejne/n6Fp0Y-TgpSdZZc.html

  • @jamaluddinlakibul4200

    @jamaluddinlakibul4200

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS boss walang available sa amin smart bond C2S1, at paano Malaman kung ang isang adsehive ay C2S1? Itong mariwasa at holcim premium adhesive pwede ba ito gamit in porcelain 60x60?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Sorry, but we do not have an idea on other brands. Kindly seek advice to its rightful manufacturer or distributor. Thank you.

  • @jamaluddinlakibul4200

    @jamaluddinlakibul4200

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS Salamat boss.

  • @joshmamaril3730
    @joshmamaril37302 жыл бұрын

    Sir tanong ko kng po..totoo po ba na natutuklap ang mga 60x60 na tiles after ilang years of installation..?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. May tendency na matuklap ang tiles dahil sa ibat ibang factors katulad nang movement nang flooring na minsan hindi kaya nang tile adhesive, kaya nirerecommend namin sa buildrite na gumamit nang smartbond.

  • @guitareasy9274
    @guitareasy92742 жыл бұрын

    Hinahaluan pa po ba ng cemento ang tile adhesive?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. No, you cannot add cement to your tile adhesive because this can reduce the effectiveness of its adhesion promoters, decreasing its adhesion and tensile strength, which results in KAPAK or tile debonding.

  • @guitareasy9274

    @guitareasy9274

    2 жыл бұрын

    @@BUILDRITECONSTRUCTIONCHEMICALS thank you

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    You're welcome

  • @jungonz9833
    @jungonz9833 Жыл бұрын

    Ani po ba Ang ihahalo sa adhesive, tiles

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi.Thank you for your inquiry.Water lang po sir ihahalo.

  • @Thefarmboy19
    @Thefarmboy196 ай бұрын

    Back to back ba mag lagay ng adhesive sir?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    6 ай бұрын

    Hi. Thank you for your inquiry.Yes pwede rin po sir para po mas makapit,Please message us on our Facebook page: facebook.com/BuildritePhils

  • @samsaxor8611
    @samsaxor86112 жыл бұрын

    paano po kapag mag iinstall ng tiles sa roofdeck after ko i waterproof ng flexicrete ohk lang ba na tile adhesive lang ang toppings kahit need pa ng slope to drain? oh need parin ang drypack para sa thickness ng toppings?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    2 жыл бұрын

    Hi. Thank you for your inquiry. We do not recommend using drypack on installing tiles. We recommend to use Buildrite's Cement grip and Hardcrete 310 to achieve a slope to drain flooring prior to the installation of tiles. You can watch this video for your reference: kzread.info/dash/bejne/ZIKYuqqfhMa0gMY.html

  • @jefreycanete6843
    @jefreycanete6843 Жыл бұрын

    Ano ang name nang powder ang adhesive gamitin para sa tile?

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    Жыл бұрын

    Hi. Thank you for your inquiry. We recommend Buildrite's Smartbond lightweight tile adhesive. You can watch this video for your reference: kzread.info/dash/bejne/eZuTxcuTYanFd5c.html

  • @jonassharma1
    @jonassharma15 ай бұрын

    Hello po. Sabi ng workers ko, magastos daw ang pag gamit ng smartbond. They started suggesting things that are not part of your recommendations. Kindly direct me to the thin bed method of tile adhesive application. Thank you po.

  • @BUILDRITECONSTRUCTIONCHEMICALS

    @BUILDRITECONSTRUCTIONCHEMICALS

    5 ай бұрын

    Hi, thank you for your inquiry. We need more information about this, please message us directly through our official facebook page: facebook.com/BuildritePhils

Келесі