How to adjust 03-06 GM truck gauge cluster needles
This is trial and error you will have to keep adjusting it until it falls on zero.
Жүктеу.....
Пікірлер: 17
@chadscheller60513 жыл бұрын
After replacing the bulbs in my instrument panel,I have been watching video after video, trying to get the needles to sit properly. I've had no luck, until I happened to come across your video. What you showed finally worked. Thank you for taking the time to post it.
@loudiemonz
3 жыл бұрын
How did you get the other needles set? All mines are a little off now after repair?
@alexzuniga29333 жыл бұрын
Ok video I been researching this for when I have to change my bulbs and adjust the needles so far there’s not many good videos explaining this well. Will try your method when I do my cluster repair.
@owa25333 жыл бұрын
Where did you get that overlay?
@Noah-nc5ey Жыл бұрын
0:47
@alexxdoesit5.314 Жыл бұрын
Hello video is great! How did you get the corvette emblem in the middle of the steering wheel??
@olegyak3539
Жыл бұрын
The airbag cover is from a trailblazer or envoy and I had the emblem made to fit in place of the Chevy emblem
@elstaticduran15574 жыл бұрын
How can you fix the others gas,oil,temp,rpms ??
@ainstaink8312
3 жыл бұрын
Same way! When power is applied to the cluster they should recalibrate at 0! All of them! Remember NO ignition!
@ainstaink83123 жыл бұрын
You are technically correct, but I would not force to move that needle the way you did. I remove them using fork and then just lighly insert it, and once you get to the right point push it in.
@marianomendoza8414
3 жыл бұрын
Have you tried removing the blue paint that the cluster has behind the numbers ?
@olegyak3539
3 жыл бұрын
@@marianomendoza8414 if you are careful you can sand off the blue film
@Ugybug1900
3 жыл бұрын
@@marianomendoza8414 you can buy replacement overlays at carradiobulbs.com that dont have the blue film
@sebastiansirias541
2 жыл бұрын
I Repair a Mercedes Benz Cluster with this method!...100% positive!!! Thanks!
@tudeddy7026
9 ай бұрын
@@olegyak3539would you sand them from the back of the cluster face? Or the front?
Пікірлер: 17
After replacing the bulbs in my instrument panel,I have been watching video after video, trying to get the needles to sit properly. I've had no luck, until I happened to come across your video. What you showed finally worked. Thank you for taking the time to post it.
@loudiemonz
3 жыл бұрын
How did you get the other needles set? All mines are a little off now after repair?
Ok video I been researching this for when I have to change my bulbs and adjust the needles so far there’s not many good videos explaining this well. Will try your method when I do my cluster repair.
Where did you get that overlay?
0:47
Hello video is great! How did you get the corvette emblem in the middle of the steering wheel??
@olegyak3539
Жыл бұрын
The airbag cover is from a trailblazer or envoy and I had the emblem made to fit in place of the Chevy emblem
How can you fix the others gas,oil,temp,rpms ??
@ainstaink8312
3 жыл бұрын
Same way! When power is applied to the cluster they should recalibrate at 0! All of them! Remember NO ignition!
You are technically correct, but I would not force to move that needle the way you did. I remove them using fork and then just lighly insert it, and once you get to the right point push it in.
@marianomendoza8414
3 жыл бұрын
Have you tried removing the blue paint that the cluster has behind the numbers ?
@olegyak3539
3 жыл бұрын
@@marianomendoza8414 if you are careful you can sand off the blue film
@Ugybug1900
3 жыл бұрын
@@marianomendoza8414 you can buy replacement overlays at carradiobulbs.com that dont have the blue film
@sebastiansirias541
2 жыл бұрын
I Repair a Mercedes Benz Cluster with this method!...100% positive!!! Thanks!
@tudeddy7026
9 ай бұрын
@@olegyak3539would you sand them from the back of the cluster face? Or the front?