Thank you for posting!! Just replaced mine on a 2007 V6 Fusion . Had to use WD40 aswell 😂.

@DavidJWarEagle

4 жыл бұрын

You’re welcome! The WD-40 trick is a good one. 👍

Thanks this was helpful for me. It was a little hard to find but this was perfect!

@DavidJWarEagle

3 жыл бұрын

Thanks for the kind words. Glad the video was helpful.

Good video. So I guess this car does not have the heated pvc valve? How often would you recommend to change the egr valve ? Thank you, Johnny

Thanks for supporting my channel!

Una pregunta si le pongo una pcv que no lleve el connector que pasa

You're a life saver seriously I can't thank you enough ❤

@DavidJWarEagle

Жыл бұрын

You’re welcome! Glad the video was helpful.

there was oil in my pcv valve?

+Ran Zhang Hi, I was thinking that $40 for the Motorcraft PCV valve was cheap considering it only needs replacing every 100,000 miles but it's certainly relative.

Is of same location on 06 ford fusion SEL 2.3. 4 cyl.

What does the pcv valve do and what are the symptoms it is bad

@DavidJWarEagle

4 жыл бұрын

Here’s some information: www.freeasestudyguides.com/pcv-system.html

Would this cause an oil leakage? My 06 ford fusion is leaking oil but not from the pan from some hose..

@DavidJWarEagle

6 жыл бұрын

Jenna McFarland It’s possible, I suppose, but it’s difficult to say without seeing where the oil is coming from.

hello Sir do you know where is the egr valve is located in this car ?

@DavidJWarEagle

3 жыл бұрын

Yes, it is bolted onto the driver’s side of the intake manifold.

is it normal for both hoses with the green tab to have alot of oil in them?

@DavidJWarEagle

10 ай бұрын

Yes, this is normal because the positive crankcase ventilation (PCV) system is pulling oil vapors out of the crankcase and into the intake. The inside of the intake manifold will be oily also for this reason.

@crimmie114

10 ай бұрын

@@DavidJWarEagle im getting codes for p0351 circuit and it missfires, i changed the vct the camshaft position sensors and the crank shaft sensor Is it a wiring problem? because i found one that was exposed?

I appreciate you showing tips but showing the actual replacement would have been helpful

@DavidJWarEagle

5 жыл бұрын

Yes, sorry about that. This was one of the first videos I did and realized afterward that I didn’t get a shot of actually removing and installing the valve. Thank you for the kind words.

Will it be in the same spot on a 2010 4 cylinder fusion?

@DavidJWarEagle

Жыл бұрын

On a 4 cylinder engine there’s only one valve cover so I think it would be towards the driver’s side of the cover. I don’t know for sure on the 4 cyl though.

@tyguyentertainment9531

Жыл бұрын

@@DavidJWarEagle thanks!

what are those mounting holes for near the oil cap?

@DavidJWarEagle

4 жыл бұрын

Mr. Roboto I believe those are for the engine cover posts that the Mercury cars have.

Is this s duratech 3.0. Need location 2007 Ford 500. PCV location

hey my fusion idles rough an the rpm will not go past 2 an my whole engine shakes during this rough idle.. so replacing that PVC valve should get it back to running normal ?

@DavidJWarEagle

6 жыл бұрын

Erskine Nesmith That doesn't sound like a PCV problem. If you have a check engine light, then you can stop by almost large chain auto parts stores and they will read the codes for you.

@squeek797

6 жыл бұрын

oh ok thanks

@DavidJWarEagle

6 жыл бұрын

Erskine Nesmith You're welcome. Let me know what you find out. Thanks for watching.

@The1WhoKnowsTheTruth

6 жыл бұрын

That sounds like the dreaded electronic throttle body failure. Sets a hard code (light with the wrench) and goes into limp mode instantly. That's the reason RPM's will not go over 2000. This is a very dangerous situation that has been discussed on many websites because folks are on the highway at speed sometimes when this failure happens and it is not fun trying to control a car that was cruising at 55mph (or more) and is now limited to only 2000 RPM in an instant. Not to mention the cars behind you when this part fails. Of course Ford will not admit there is a problem with the original throttle bodies electronics and will not issue a recall. But they have since re-designed the part. Typical. Here: kzread.info/dash/bejne/eHikt9FshbPTpNI.html

How do I know the part number by the chassis number of my Mercury Grand Marquis

@DavidJWarEagle

3 жыл бұрын

Most OEM parts websites will ask for the VIN of the vehicle. From there you can search for the appropriate parts for your car. You should be able to find a website if you search for “OEM Ford Parts.”

@ali_almehaiza

3 жыл бұрын

@@DavidJWarEagle Thank you so much

Were is the vct solenoid on this car please

@DavidJWarEagle

4 жыл бұрын

There is a VCT solenoid on both banks/heads of the 3.0 V6 on the passenger side. They stick up through the rocker/valve cover where the harness connects to them.

The video was okay for showing were to locate the part but why not show how to remove and replace it?

@DavidJWarEagle

3 жыл бұрын

This was an early video but you turn it counter clockwise to remove it. I sprayed a little WD-40 where it connects to the valve cover to make it easier to turn. I tried to show the removal technique towards the end of the video.

It is not cheap, since it cost about 40 dollar. I also replaced it even though i did when i replaced spark plugs and upper intake manifold gaskets. Warning: do not mess with that stupid EGR valve. It is very hard to change EGR valve gasket. I have a leak in the EGR now after replacing the gasket.

@jeogriffith

5 жыл бұрын

Yes, me too. What to do???

how did you get it out??

@DavidJWarEagle

7 жыл бұрын

Tim Combs Turn it counter-clockwise. If it's stuck spray some WD-40 on it where it connects to the engine, wait a few minutes and try again.

@tonycervantes4816

4 жыл бұрын

@@DavidJWarEagle is neccessary change it. My car have 172000 miles you think I need change it .?

Cheap part , lol, they want 75$ for it in Chicago area.

@J.RRandallIllinois

2 жыл бұрын

Thanks for the video

@DavidJWarEagle

2 жыл бұрын

You’re welcome! It used to be cheap!