Lovely boat! But please stop standing on it on land any sharp object could go through it and then it will feel very second hand I watched someone do it on KZread the other day!! 👍

@expedition-UK

2 жыл бұрын

Thanks😉, Good advice 👍 Next time will try to avoid standing on it, while assembling.

Looks like you decided to fit transom wheels was it too heavy to lift down the slip ? We bought wheels for are Honwave but they don't fit what one's did you get ? And we also had trouble with are Air Pump (boatworld) fitting the Honwave valve and had to cut the centre bar out and take some of the meat off the bits that clip in to make them thinner it now fits perfectly.

@expedition-UK

2 жыл бұрын

Hi, yes it’s way to heavy to carry without wheels (probably around 140 kg with outboard attached) with wheels i can launch it on my own. I’m not sure brand of the wheels (i been offered at shop where i find a boat and outboard- Simpson marine-Newhaven) Wich Honwave do you have?

@oliverskinner8962

2 жыл бұрын

@@expedition-UK T38IE3 the one without trim tabs 2021 but the wheels we have don't have enough clearance and will rub the bottom of the boat if we fit them they are the easy fold spring loaded type that fold up onto the transom not the type that are longer and stick above the transom.

The other videos that I have seen say that it is best to partially inflate the boat first. What does it say in the instructions please?

@chrisseymour3027

2 жыл бұрын

On a side note....Where did you launch? I seem to recognise the blue van that you are parked next to (It's a custom van). It's quite distinctive!

@expedition-UK

2 жыл бұрын

Hi Chris, for me personally much easier to put ali floor in place when not inflated at all😉 I did launch from Newhaven-Simpson Marine slip. It cost 10£.

@chrisseymour3027

2 жыл бұрын

@@expedition-UK Thanks. Unlikely to be the same van.

There are so many Honwave and other inflatables that show how to unpack and inflate your new boat. There are absolutely none that shows how to deflate and pack away your boat, plus sizes for people to plan for their individual road car or vehicle. Will the deflated Honwave T40 fit in a car roof storage box, etc. These things are important too.

@boatsandoutboards9070

Жыл бұрын

This video may help : kzread.info/dash/bejne/nn6hmqtwfNC7f8o.html

@boatsandoutboards9070

Жыл бұрын

or this one : kzread.info/dash/bejne/p3tnlcWBZ82ehLQ.html

Having trouble finding the right air pump, that does not need a power supply from my vehicle that will be parked some distance away. What pump are you using and the cost of the pump is also important.

@flamintasty

2 жыл бұрын

Use a leaf blower, it will inflate the sib in a tenth of the time a 12V pump takes. Then simply top up the air with either a high pressure foot pump or a 12V pump. The whole exercise will then take a little over 2 minutes. Look for a video by SOUTHYS FISHING, he shows exactly what you need and how to do it.

@boatsandoutboards9070

Жыл бұрын

definitely the 18volt leaf blowers are the fastest and best for boating. you can blow away the sand inside the boat,dry the boat , and also dry the motor after freshwater flushing.

Hey, thanks for the video, the floor looks a bit of a pain to do, is that right?

@gaatjenietaanprivacy5023

Жыл бұрын

They actually should first fill the boat to about 60-70% first and afterwards put the plates in, because then the air chaimbers have been formed already, which makes it easier to lay the plates and fit it quicker.

@markweatherall7437

Жыл бұрын

​@@gaatjenietaanprivacy5023 Ok thanks for your comment. Does that model have an inflatable floor/keel for the floor to rest on?

@gaatjenietaanprivacy5023

Жыл бұрын

@@markweatherall7437 Yes, it does. In the front panel there is a hole in which the tube fits to pump up/down the floor/keel to rest on.

Wanted to see how you carry the Engine . Was disappointed . I am having trouble carrying the engine , even with 2 man lifting , still feeling hard

@expedition-UK

2 жыл бұрын

I do agree it’s heavy, but still manageable. Will do full video on next fishing trip.😉👍

If you would read the manula you would have no trouble fixing the floor with beem poles. I gues most people today think manuals are just garbage... Funny

Nice video thanks; i have a question for you about it's total weight about 86 kg: how many kg for pvc and how many for the 4 aluminium pannels?Thank you for answer

@expedition-UK

Жыл бұрын

Thanks 😉 I would say 50 kg boat and 36 aliuminium floor. I could be wrong, but those panels is heavy 😏

@domenicogiannattasio9037

Жыл бұрын

@@expedition-UK many many thanks ; It Is not important the exact weight of parts only understanding if i can or cannot able to bring by myself PVC to be indipendent without disturb my friends 😄

@expedition-UK

Жыл бұрын

@@domenicogiannattasio9037 Honwave T38 just 48 kg with inflatable floor.

@domenicogiannattasio9037

Жыл бұрын

I know t38 Is very light but navigation Is not same than t40. Thanks again

@boatsandoutboards9070

Жыл бұрын

@Domenico : You can generally say that half of total weight is the pvc boat, the other half is panels+aluminum panel bars+seats. You can carry the panels etc piece by piece in separate bags, and it's never a problem. Bare boat weight is the problem here. T38ie inflatable bottom is definitely lighter than an aluminum floor model, but that weight 48kg comes in one piece and in a very very large bag.

How much was the boat

@expedition-UK

2 жыл бұрын

Hi Richard, it was around 4k new.

شركة هني ويف

С таким смешным насосом даже не накачали до полного давления…😂

Not like this. The inflaating steps are wrong