This series with the 2003 350 has been the most helpful thing entirely, thank u partzilla

Glad I found this guy and Partzilla. I was looking for a quad and my brother-in-law found me a 2001 Honda Rancher4x4 ES Orange! It didn’t leak oil, no smoke and sounds pretty good. Gave it some long needed TLC and man It’s like new. But these videos help me get it purring like a cat!!! Thanks! Oh and by the way I had never worked on machines or cars before…

@PartzillaParts

Жыл бұрын

Very cool!

Thank you for another excellent video. I had no idea it could be that easy. I haven't done it yet, but thank you for taking away the intimidation factor.

Great clear video !!

excellent videos and excellent mechanic!

Muy bien su video. Podría poner un vídeo en español como calibrar válvulas de honda 350 fourtrax rancher

Muy buenos videos maestro una pregunta tengo una honda trx350 fourtrax rancher si le puedo poner un carburador clon no es el original de la honda

after I adjusted the valves startup sounded great, a short test run was great but after a longer run time when engine was warmed up the valves became noisier than before they were adjusted. adjusted them again after engine cooled down and the same thing happened when the engine warmed up. wondering what the issue is?

Great info

I have a 06 rancher 350 4x4 and we put a new jug and head on it today. Along with a new carb and fresh gas. It only turns over. It won’t start. Put new plug in it and make sure it had spark. After spraying some starting fluid, it backfired a few times but never acted like it wanted to start.

@jeremyriordan

Жыл бұрын

What was the fix??

@miked8227

Жыл бұрын

Carb clean I’m guessing or ignition switch

Please make a starter clutch replacement video. I have a yamaha grizzly 80 with a bad starter clutch and I can't find anything out there that'd help me figure it out

Rebuilt the top end of my 01 trx350 and it is running rich to the point of a new spark plug being completely back after only running a few minutes. Any advice?

Do you guys sell a manual for a 2004 rancher 350?. Something that has all this In writing with diagrams, like the old Chilton manuals

Im at the T and they are very tight doesn't have play on roker arms

Saludos desde Honduras. Tengo una cuatrimoto Honda rancher 350 2006. Pero suena como martilleo solo cuando acelero ya regule Las válvulas cree que podría ser desgaste de la biela? Espero saber pronto dé usted. Muchas gracias.

I adjusted the valves on my Honda rancher 420 but they got louder I double checked them and It was on the correct stroke each time

@PartzillaParts

5 жыл бұрын

Did you double check your measurements?

@wyattmac9701

5 жыл бұрын

@@PartzillaParts I happened to do it agian and I noticed they have to be kinda tight or they will be off I had to make sure that they were tight till they the next size up wouldn't go in is that normal? Or is it worn out?

Good video but I'd add check the adjustment before you loosen the lock nut. It might be OK.

How do I know when my 03’ rancher needs this adjustment. I have about 1800 miles on it. (If it ain’t broke don’t fix it?)

What is the torque spec on the valve cover bolts 🔩

Is it pretty similar to a 1988 Honda 350 TRX

Hey I’ve got a 400 odes it’s the clone for this motor would valve clearance be same

@jdorney70

5 жыл бұрын

I also have an Odes 400. I followed his procedure and the old girl seems to run fine. Does your suspension ride like a buck board? I put Honda Rancher shocks on it and it helped a little, but not much.

Great job on all the videos !

So I have this same exact bike and I was going fast and it was ticking already and it lost power and started trying to stall hasn't started then and when I do try to start it it backfires alot but sounds like it's trying to start normally but doesn't start is this the valves?

@blazin3353

3 жыл бұрын

Piston rings. Mine just did the very same thing. Had to do a whole top end rebuild

I have no play when lined up to the T. I only get play slightly past the T. Do i make my adjustments from there? Thanks.

@Nunya_Beezwax

2 жыл бұрын

Yes. Obviously your timing chain is slightly stretched

After doing a top end job should these be readjusted?

How do 8 turn the engine over to TDC if I don't have the pulling anymore?

@loikborris9832

2 жыл бұрын

rachet

Hey! I have a honda trx350fe 2001 model.. one day i was out plowing with it it the electric gearing started to get slower and weirder so i had to push it back and fourth to shift. And suddenly it was stuck in reverse.... i went in and when i got out i got it in neutral and pushes it in the garage.. later i opened the gearbox and i didnt see anything wrong and right after i opened the crankcase cover the gearing was fine again.... so i was riding it and suddenly the same happened i tried with the manually shifter and it didn’t work.... and sometimes the elextric shift works and sometimes it dont, And the with the manualy shifter. Can it be the clutch? Every time i push the electric shift buttons i can hear that it is trying... but wont shift.. and nothing happens when i turn the manually shifter. Please help. It’s pissing me off!

@josteintrotlandbrattli7477

6 жыл бұрын

I have also tried adjusting the clutch....

@PartzillaParts

6 жыл бұрын

A couple of basic questions. 1.) What oil are you running and when was it changed last prior to the shifting issues? 2.) When you "I opened the gearbox and I didn’t see anything wrong and right after I opened the crankcase cover the gearing was fine again" were you looking at the clutch/gear shift linkage on the front facing side of the engine? If so did you try to move the gearshift shaft to feel any binding inside the transmission?

Thank you

With the valve being out of adjustment will it cause it to smoke?

@PartzillaParts

5 жыл бұрын

it could, but more likely you are leaking excess fluid into the cylinder.

@jmooregbc3

Жыл бұрын

@@PartzillaParts which means?

Sonbuenos su videos pero. Serian mejor ponerlos en español o los subtítulos. Para poder a yudar a la gente.

Your four wheeler takes a heck of a lot longer to start than mine does... Why is that?

@svtirefire

2 жыл бұрын

Because he didn't have the choke on at first

How many milliliters is the gap on the valves?

@loikborris9832

2 жыл бұрын

.006mm

What's torque on valve cover bolts??

@PartzillaParts

6 жыл бұрын

Torque for those size bolts is 7ft lbs

@zachmosteller4681

5 жыл бұрын

@@PartzillaParts are the value cover gaskets reusable on a 2001 honda recon 250?

@repairsreviews146

5 жыл бұрын

@@zachmosteller4681 I wouldn't reuse the gasket, it's cheap enough to replace. I just bought a 05 and the valve cover gasket is leaking pretty bad so I'll be replacing it and adjusting valves while I'm there.

@zachmosteller4681

5 жыл бұрын

@@repairsreviews146 oh I didn't know I called honda and asked them and they said it will be ok to reuse it especially since my engine has never been disassembled

@repairsreviews146

5 жыл бұрын

@@zachmosteller4681 it might be fine to reuse but if it was me I'd replace it for less than 10$ just in case. Kinda a pain to pull fuel tank again if it happened to leak.

Bueno de todas maneras ni contestan tus preguntas. De que serve preguntar. Sale sobrando

I want to clean that mud off that machine so bad!

First!

@miguelgaldamez8929

Жыл бұрын

Saludos desde Honduras. Tengo una cuatrimoto Honda rancher 350 2006. Pero suena como martilleo solo cuando acelero ya regule Las válvulas cree que podría ser desgaste de la biela? Espero saber pronto dé usted. Muchas gracias.