Honda CR-V: Replacing the Floor | Watch This Before You Start!
Автокөліктер мен көлік құралдары
Check out my shop for all toolslinktr.ee/AUTOBODYTECH
Hey guys, this video will be 1 of 2 parts of this rear end collision repair
in this video, I'll be removing and replacing the rear floor of this Honda CR-V
/ autobodytech01
As an Amazon Associate, I earn a small commission from qualifying purchases. Some of the links are affiliate links and if you decide to buy the tools through them I earn a tiny commission. It costs you nothing but helps me big time.
7 Piece Dura Block Sanding Kit:amzn.to/48xvNj3
Steck Quarter Panel Puller 20022:amzn.to/48NjvCJ
Astro Pneumatic Tool 930 Mini Reciprocating Air Sawamzn.to/41SYQeq
Sunex SX8200 Surface Blaster Kit:amzn.to/48J7Swz
The MAXI - 220v:www.dentfix.com/shop-1/The-MA...
Evercoat Rage OPTEX Color Changing Filler:amzn.to/3OhiHhR
Evercoat 425 Metal Glaze Ultra 30oz:amzn.to/492KXg7
Canadian Tool and Supply 7-Inch Air Angle:amzn.to/3tJ2zOQ
Wurth 1/4" ANGLED 90 DEGREE DIE GRINDER:shop.wurth.ca/general-tools/p...
Mirka MR-6 Finishing Sander:amzn.to/3vrjje5
Body Line Tool:amzn.to/3tNoZP1
Martin 1024 9" Blade Surfacing Spoon:amzn.to/3SbJ8I5
Uni spotter 5500:www.toolsource.com/stud-welde...
3M Belt Sander:amzn.to/48qO4hI
Milwaukee M12 FUEL 3/8 Stubby Impact:amzn.to/3H9va2V
#autobodyrepair #automotive #car #welding #autobodytech
Пікірлер: 16
Check out part 2 where I finish the job! kzread.info/dash/bejne/hX5rw8NqYMSqqJM.html
What type of drill bits you used to drill hss it would really help to know I appreciate ?
@AUTOBODYTECH
Жыл бұрын
Hey! It's best to order those upper plates but in my case the parts wouldn't have been available for a few weeks so I decided to drill them. These are the drill bits I used. Hope this helps www.lawsonproducts.com/Supertanium/Solid-Drill-Bit-Carbide-516/P58047.lp
Where do you get the procedures for body panel replacement?
@AUTOBODYTECH
7 ай бұрын
It's called all data. You need to pay monthly
@literailly
7 ай бұрын
@@AUTOBODYTECH thanks! I have a Sienna that was whacked hard on the rear driver side. Unibody is kinked just behind where suspension attaches. Drives fine, but not clear yet if repair is worthwhile
How long it took for cutting an welding everything all back together those Hondas are a really paint in butt it’s just way over engineered
@AUTOBODYTECH
Жыл бұрын
Hey! Agreed, this one is was quite a pain. I think this one took a solid 3 days of work. thanks!
@AlfredoHernandez-fh5fk
Жыл бұрын
I’m doing one right now and it’s just so stupid the design it help a lot your video bro thanks keep up the good work ✊🏽👊🏾
These are awesome videos @AUTOBODYTECH quick question, for a DIY'r where could one go to get replacement floor panels, etc.. like you showed here? Can the average person go to Honda/Toyota and purchase these, or are they gonna say no because I'm not a business?
@AUTOBODYTECH
Ай бұрын
@@kseries20-24only you can order any part you'd like at your local dealer parts department. It shouldn't be a problem
@kseries20-24only
Ай бұрын
Awesome! I'll have to give it a shot some day, I've got an 02 RSX similar damage to this I doubt they make those panels for anymore, have to find a donor car to cut apart for my first attempt.. :/ You just gained a subscriber!
@AUTOBODYTECH
Ай бұрын
@kseries20-24only it's quite old, but you might get lucky, and they may have it available. Other than that, your other option could be asking a bodyshop if they can order you a salavged rear end from an 02 rsx. This way, you'll have everything you need for it plus extra
@kseries20-24only
Ай бұрын
Great ideas!
How many hours did you get paid to do that whole job. I'm doing the exact same job now and this is a piss poor paying job
@AUTOBODYTECH
4 ай бұрын
Probably 30-40hours? Don't forget to get the mechanical time as well. Agreed for something like this.. it doesn't pay well. Have fun!!