1:40 RX is the receive pin, TX is the transmit pin. RX always goes on TX and vice versa. ;-)

@Od_13

11 ай бұрын

Yup. Gets real complicated when you have multiple levels of TTL. To set yourself up for success if you ever want to play with arduinos: Think of them only as SIGNAL NAMES. NOT DIRECTION OF "FLOW"

Such a good video. Thanks for posting and explaining all of this i couldnt find detailed info on this. Subbed

@BudgetGears

10 ай бұрын

Thanks 😊 appreciate the sub 🙏

Nice tutorial my dude!

@dasboseimbusch7079

Жыл бұрын

Is it also possible to use the Smart Port Scan with the HC-05/HC-06 ?

@dasboseimbusch7079

Жыл бұрын

I just tried it. It works. Good job HTS ;-)

I'm using same setup it give me hard time but I got it done

Tx is whats transferring out of the ecu. Pin 2 on board. You need the other side to catch the signal on recieve. The software is requesting these packets, to send them to the computer it needs to send the signal to RX for received. Dont think of them as flows, just signal names.

Great video! Any chance this can work on a phone app? Trying to do a fuel economy VX with active MPG displayed on my phone

@BudgetGears

Жыл бұрын

Yes, I've successfully used it on Hondash, but haven't tried TunerView yet because it required the purchase of the protocol and I didn't want to or need to spend the money for it. But others have used it on TunerView and had no problems. So yes, you can use it on phone apps.

Hi, I have a P28 with my stock D16Z6, I flashed a HC05 and HC06, but when connected to Hondash it says can't read from ECU or can't connect to the ECU.. I will try with another app..

Hi what must buy hc05 slave or master? What is the difference if hc06 there is button

I followed all the instructions from this and the previous video and despite this, my hc05 will only stay connected for about two seconds, then shut off. Any advice?

Thanks for the tutorial, will give this a try! If you attach the HC-05 to the inside of the ECU, will the bluetooth signal still make it outside once you screw the ECU lid back on?

@BudgetGears

11 ай бұрын

Yes, I've tuned with the ECU lid on only and works fine. I'm pretty sure almost everyone places it inside the ECU.

@timwalther

11 ай бұрын

@@BudgetGears Thanks for getting back to me, appreciate it!

What do you call that cable that connect HC05 and Laptop? Thanks! Great video! :)

@BudgetGears

Жыл бұрын

FTDI cable.You can also datalog directly with the FTDI cable as well.

Can you upload that 3d print?

Cool video......I used the instructions in the video and it worked great. Awhile later my ECU needed repair, after getting it back from being repaired I can't get it to work again. The Bluetooth seems to work but my problem is HTS can't open com port 9 and I can't datalog. Should I try to reprogram the HC-05? Any suggestions?

@BudgetGears

Жыл бұрын

Not really sure. I'd suggest trying to reset it and then program again and make sure you select the com port that is outgoing.

@Muzamil.Rind1

Жыл бұрын

@@BudgetGears can you also edit tune with this data logger?

@BudgetGears

Жыл бұрын

@@Muzamil.Rind1 No, it's called a datalogger. It's in the name. It logs data. If you're looking to tune, you'll need a programmer. Either tune by burning chips, which is a eeprom programmer or by using an emulator, which would be the many RTP's on the market.

What about if your using a moates ostrich for your emulator, you still would have to connect your ribbon cable to your laptop right? Since the data logger and emulator are two separate USB connections

@BudgetGears

6 ай бұрын

Yes, datalogging and the emulator are 2 separate things. So you'll still have to connect the ribbon from the ostrich. Only the datalogger will be wireless.

Do you have a wideband connected and can read that well? And if yes you wired it at narrowband pin on ecu?

@BudgetGears

Жыл бұрын

Yes, I have a wideband connected and yes I used same pin as narrowband. As well as used power and ground from ecu. And yes, it read no problem.

Donde puedo comprar la pieza ???

Signal flow I'm guessing. If one side is transmitting(tx) then the other side is receiving (rx).

@BudgetGears

Жыл бұрын

Thats kinda what I was thinking too. But didn't make much sense with how the ecu datalog pinout is. Unless the actual pinout is opposite of what the wiring is on the forums. I guess as long as it works. 😁

Where did you get the cable to hook the Hc05 to the ecu? If you built one what size are the pin connectors?

@BudgetGears

8 ай бұрын

Just search for dupont connectors.

can you program it wirelessly, like a normal ecu tuning ? or is there any delay on the readings? im planning to learn how to tune my own car :) (newbie)

@BudgetGears

7 ай бұрын

No, this is a datalogger. It's exactly what the name is, it only logs data. In other words, it only reads data and doesn't write it. For you to write data, you need an emulator. The readings you obtain from the datalogger is used to make adjustments to your map. You then write the map in real time using an emulator or not in real time by burning a chip and swapping out the old chip with the new.

@rorenstv9051

7 ай бұрын

@@BudgetGears Thank you very much for answering my question it is a very big help for me since im just starting to learn how to tune :) thanks

Hi i have hc05 but can turn to read

My HC06 has no button??? Anyone know how to put it in AT mode???

I have a Civic coupe D16z6 - 1995 equipped with a P28 ECU - with no modifications. Do i need do something about jumper J12 in order to comunicate via serial CN2 conector as you did?

@BudgetGears

Жыл бұрын

You'll need to chip your ecu and remove J12 to use the CN2 port for datalogging.

@ftonello1

Жыл бұрын

🤦🏻now i got it. the chipped rom has the codes to conunicate with the serial, ins't? i thougth i has a pure RS-232 TTL serial there at that pins... Mine doesnt have a chip...the board looks like new... in alternative. do you know if will work with hondash?

@BudgetGears

Жыл бұрын

@@ftonello1 I've used Hondash on my chipped ecu's, but never tried datalogging on a unmodified ecu. I'm not familiar with getting the CN2 port to work on a unmodified ECU, but someone must have done it out there. I don't see a point in datalogging a stock ecu, but I guess some people may like it as a display or something.

@ftonello1

Жыл бұрын

@@BudgetGears You´re complete right about dataloggin. The only point i see using hondash, is that you can makle a very low profile diagnosis, using the data that comes from stock ecu, to check the basics about your engine, mainly, if the cluster is working by compairing with the hondash. The rest is pure cosmetics. Thank you and congrats on your videos!

Will this work on a stock box? I have a P08

@BudgetGears

Жыл бұрын

What do you mean stock box? Like an not chipped ECU? I haven't ever tried to datalog on a stock ECU. It's always been chipped. Plus, you'll need to remove a resister to datalog on certain programs. Not sure which one it is for the P08 because that's a JDM ECU.

What’s up my guy? I got a chipped p28 and I’m trying to get into tuning but idk what to get to connect to my ecu to my laptop. Thanks in advance.

@BudgetGears

10 ай бұрын

If you want RTP, then you'll need to run an emulator. The datalogger can be either bluetooth or cable. So you'll essentially have 2 connections. One from emulator and 1 from datalogger. If you're just doing it without a emulator, then just a datalogger to connect to computer and you'll need to remove your chip each time you make a change, burn the new rom, and then put the chip back. I'd suggest doing some reading on honda tuning to get the basics down.

@roccodadon4211

10 ай бұрын

@@BudgetGears thanks 🙏🏾

Can we get all links

can i just use the cable to datalog ?

@BudgetGears

8 ай бұрын

Yes, you can check my other video on how. kzread.info/dash/bejne/nHWHzNp-mqi4h5M.htmlsi=lT7NZido0ML0GTGh

hello I tried to connect hc05 to honda tunjng suite but it is still promting failed to enter at mode after clicking connect on bluetotth setup hehe do you know why or how to fix it ? thanks

@meditationlife9337

5 ай бұрын

There lots of different factory made HC05 . I got four different hc05 module and just one working ın my car. I tried before other 3 different mark HC05 ın HTS Bluetooth program tool but fail.

@rorenstv9051

5 ай бұрын

@@meditationlife9337 i messed up my ecu trying to remove the cn2 pins i placed haha it pulls the copper traces from the board so now i will send it to someone who repairs pcb and ecu

my problem is with the hc-05 connection, is the hc-05 set to slave and master?

@BudgetGears

Жыл бұрын

Slave. The master function is more for devices that search for other Bluetooth devices. Like your phone or PC. Since you use your phone or PC to search for the hc05 to datalog, it should be set to slave. Slave is also the default setting.

Can't pass step 2. I have two different cables, none of them work. One says Failed to enter AT mode, the other one just does nothing. What I did wrong? It recognizes the COM port automatically but can't connect to it. Thank you for your help! Edit: I got it fixed by change the RX and TX. My bad.

@Kdiset

3 ай бұрын

Hello, I have the same problem as you, how did you do it? mine can connect but can't read. please help me 😑

@ImBenny

3 ай бұрын

@@Kdiset which bluetooth module do you have?

@Kdiset

3 ай бұрын

@@ImBenny HC-05 bluetooth and TTL cable

@carlosbertoldi5603

2 ай бұрын

@@Kdiset change the RX and TX and black conector usb no blue 3.0

What is the small cable called please?

@BudgetGears

Жыл бұрын

Dupont connectors/wires

I do all the steps like the video but when i do the restart module it doesn't do it and not flashing tge light

@watchitwithme4016

4 ай бұрын

Did you hold the button before you plugged it in happened to me once

I tried this but hts sayscant conect to ecu check debug logs.. i am in the right com (outgoing) before that it said maximum number of series reached

@BudgetGears

2 ай бұрын

Sounds like you're trying to connect using emulator. This tutorial is for datalogging. If you're having issues with your emulator, then you need to contact your emulator manufacturer.

@shahul11p98

2 ай бұрын

@@BudgetGears i dont have any emulator with me sir, i am very new to this please help

@BudgetGears

2 ай бұрын

@@shahul11p98 Then connect using datalogger. You can only datalog if you don't have a emulator. Not sure why you're connecting using ECU then.

Hello, I do all the process but in hts, the datalog button is disabled. :(

@BudgetGears

6 ай бұрын

I wouldn't now what's wrong. You're better off asking the guys at HTS because it's their software. I know there's been many versions since this video so they could have changed some of the coding.

I've successfully flashed the HC05. My phone can detect it but Hondash app says can't connect to ECU. My notebook can't even detect the HC05 module. What could be the problem?

@BudgetGears

10 ай бұрын

Did you flip tx and rx back for your cn2 port on the ecu?

@ImBenny

10 ай бұрын

@@BudgetGears It was a setting I had to switch in Windows 11 to detect this device. Now I can connect with my laptop but HC05 doesn't transmit data. I tried switching tx and rx but still can't get it work. J12 jumper is removed.

@BudgetGears

10 ай бұрын

@@ImBenny you're datalogging with hts? Is it a hts map on your chip or emulator? Has to be the same to datalog.

@ImBenny

10 ай бұрын

@@BudgetGears Yes. The ECU is flashed with HTS rom. So it is on chip. Now I'm trying to connect with USB to serial cable but I get the same result so I think my ECU may be faulty. :( Or datalog can't work without emulator?

Hello, friend. I've tried to program hc-05 with HTS, but without success. Despite of this, i've programmed with other software, changed the name and it connects fine on my laptop. But the HTS software doesn't enable the START option on Datalog Menu... I had changed the COM port to COM6 and COM6 (ingoing and outgoing), but i can't even try to connect and see logs, because my software doesn't allow. You can help me?

@BudgetGears

Жыл бұрын

Did you remove J12 resistor? Also, do you have a HTS rom running on your ECU. You'll need this to be able to datalog on HTS.

@k7franklinbr

Жыл бұрын

@@BudgetGears thank you so much. how can I check if my remap uses an hts rom? I’ve bought the car already with map

@BudgetGears

Жыл бұрын

@@k7franklinbr that depends on if your ecu is just a burned chipped or you're running a emulator. But essentially you need to read the rom on your chip or emulator and look at what's programmed. HTS is usually tagged HONDATUNESUITE in the last buffer address. You can also read the rom and then save it and try to open in HTS. It will give you warning or not open if its not HTS rom.

@k7franklinbr

Жыл бұрын

@@BudgetGears The big problem is my HTS doesn't show START DATALOG option enabled. It shows disabled in gray. In your videos it was always enabled.

@BudgetGears

Жыл бұрын

@@k7franklinbr its because I'm running a HTS rom. Here's what you need to try, create a new HTS map, burn it to your chip or load it to your emulator, whichever you have, now try datalogging. The datalog only works on HTS with a HTS rom. Here's another example, people use tunerview and the hc05 to have a digital datalog on their phone for their car, tunerview requires you to select the protocol for your map. So if you're using HTS, you'd buy the HTS protocol and if you're using crome, you'd buy that, hondata, you'd buy that etc. HTS software can only datalog a HTS rom. In other words, you can't have a crome rom and try to use HTS to datalog it. You'll need to burn HTS rom then you can datalog.

my datalog says the o2 is running 1v after warm, is it normal or is it running too rich?

@BudgetGears

11 ай бұрын

Why are you datalogging with a narrowband? You need to get readings with a wideband. A narrowband has a very limited range. I can't tell you if it's normal because your car needs to be tuned to stoichiometric AFR with a wideband first.

@FeraAlfian-vu1wy

11 ай бұрын

@@BudgetGears do you mean I can use wideband for only when datalogging or I can use it daily?

@BudgetGears

11 ай бұрын

Depends on how you want to do it. Some drive with wideband even after tuning and some take it off after tuning. It is recommended to keep the wideband even after tuning if you're a built motor. It's a peace of mind when you've invested thousands into a motor. But wideband sensors tend to die pretty quickly. Really up to you. I honestly have no idea what you're doing. I'd say hook up your wideband and if you're wideband readings are what you expect, then you're fine. Narrowband only can read between 14-15 AFR. So you can imagine how inaccurate it is when you're car isn't always stoich.

@FeraAlfian-vu1wy

11 ай бұрын

@@BudgetGears got it, just want my car to run smoothly but it seems like it's not as easy as it seems. it has 100k miles on it, I've spent thousands already and now I just like to play around to know my engine better. It's D16Z6 btw, Thank you very much for your response :)

@BudgetGears

11 ай бұрын

@@FeraAlfian-vu1wy That's pretty low mileage. Is your engine all stock? What kind of issues are you experiencing? If it's all stock, there's really no benefit in running a chipped ECU. You're actually better off running an unmodified stock ECU. The maps on a stock ECU vs a chipped ECU will run differently. I'm assuming since you're datalogging, you might be running a chipped ECU.

How about for hc06

@BudgetGears

Жыл бұрын

Yes, you can do the exactly same process with hc06. Just you'll select hc06 in HTS.

will this work with obd2?

@BudgetGears

Жыл бұрын

No. If you have obd2, you'll have an obd2 scanner port. You can just hook up a bluetooth scanner to that port and view things.

@hectorjauregui5944

Жыл бұрын

@@BudgetGears thank you I figured, do you know of a cheap way to tune an obd2 computer in specific I have a 98 civic ex coupe and want to tune the car but I don’t want to spend crazy money on ecu like haltech

@BudgetGears

Жыл бұрын

@@hectorjauregui5944 I'm not going to say it's not possible to tune the obd2 computers because some have done it back in the day. But it'll be near impossible to find any info on that as it was not a common thing to do back then and something no one does now. Tuning your car in general will not be something cheap. The cheapest and easiest way to tune an obd2 car was to convert it to obd1. If you can find a cheap obd1 ecu, chip it, run a obd2 to obd1 jumper harness, and find yourself maybe a moates ostrich, that would typically be the cheapest way to do it. That being said, obd1 ecu's have gone up in price significantly and it's very old technology. It'll probably run you around 500-1000 for a ecu, with emulator, and jumper harness, etc. But still cheaper than the Haltech. You can essentially get a Fueltech as well. Those are reasonably priced, but still about 1000 for that.

@hectorjauregui5944

Жыл бұрын

@@BudgetGears yeah I’ll definitely do my research and thanks for the reply it helped a lot!

Is it possible to upload data from the laptop to the ecu? using Bluetooth connection? or it is for realtime logging only?

@BudgetGears

Жыл бұрын

Datalogging is datalogging. It only reads data. For uploading data, which is the tune, you'll be doing that through your emulator (also know as RTP (real-time programming). They're 2 separate processes. I don't know of any emulators that are wireless. All the emulators I came across usually requires a cable connection from ECU to laptop.

@chesternoriega6415

Жыл бұрын

@@BudgetGears Thank you for the information. I was just wondering weather we can also convert the signal from the cable to wireless for easier programming

@reykristophercantaco1418

Жыл бұрын

Why my hc05 cant read though i follow your vid

@BudgetGears

Жыл бұрын

@@reykristophercantaco1418 I don't know. You didn't provide much detail except it can't read. So it could be many reasons. Bad HC05, input output wiring reversed, bad ecu, J12 resistor not removed, software not setup correctly, using software that's not HTS, programming not done correctly, comm port not correct, etc etc etc. The list goes on. If the steps were followed exactly, then it should work. If it doesn't, then something else is wrong.

@reykristophercantaco1418

Жыл бұрын

@@BudgetGears i am only on the stage of programing like you do in the vid but it cant read after i connect i swtich wring but still cant buti it is in at mode

Im stuck @ step 2. i even switch the tx and rx still nothing happens. 😢

@vakhomakharashvili1800

7 ай бұрын

Did you find the solution ? Same problem here