From music to toys, you just can't beat the 80's.

Nice video, Thanks for sharing, The 200x is my favorite ATC

Nice 200x dudes

Dang they are savage 200x's

Minty fresh 🔥

I could ride a wheelie on one for miles!!! I miss it!!!

You can put h4 led bulb in stock headlamp

ATD-ATC makes some very nice skid plates, just got one for my 350x, they're on facebook. Very nice people to deal with. Would buy again without hesitation. They also make some trick grab bars, purchased their desert bar and love it!

@Trikekid84

3 жыл бұрын

Yeah it will run ether way, the circle is suppose to be up, that's what the book shows so I would just make sure its like that, and if you're off one tooth it can spit fuel/exhaust soot out the carb, mine was doing that when it was off. the backfiring is spark timing, it means its too advanced. instead of lining everything back up, you can just move the timing back a little and try again. There is suppose to be oil in the stator cover, not sure why but that's how they are. When my bikes are cold and I blip the throttle too fast, they will die, its ether too cold or there is not enough fuel, meaning your pilot jet might be clogged up. I never had one be too rich right of idle, but if the main jet is too rich it will be like it hits a rev limiter at a certain RPM, I leaned mine out and now it finally runs good. But now my kicker spring failed and the whole engine has to come apart, COMPLETLY APART! Down to the splitting the case and removing the crank, and trans. Hopefully this helps.

Man, I want a 200x again so bad.

@Trikekid84

3 жыл бұрын

I'd say buy another one and fix it up, all the ones I see for sale now are beat up bad, or really nice asking $2000-almost $3000. But still cheaper than a 250r.

@danjim7056

3 жыл бұрын

@@Trikekid84 my dad still had my child hood one sitting in a barn I'm trying to sweet talk him out of. It's an 86 and from what I remember it was in great shape, it's been in the barn for 15ish years now so who knows.

Bro… you HAVE to replace that “no FAT chics” sticker before you do anything else to that 200X ! 4:33 Baaaahahahahaha

😁👽👍

Nice trike, I'm doing the same build with a flat slide 32mm carb. What throttle cable did you use?

@Trikekid84

3 жыл бұрын

I used the stock one, but you have to get rid of the adjustment knob and screw the cable all the way into the thumb throttle part. Hard to explain but you have to make the stock cable as short as possible on that end so I had to get rid of that screw pice. 32mm is huge! Probably have alot of top end pull.

#makeatcsgreatagain

Cool bikes guys I'm in the process of building an 85 200x and I need an intake what was that intake you said you had on yours some sort of 30mm ebay one. I've heard some say on forums that an xr200 intake fits but then I seen reviews on new cheap ones and people say they don't fit a 200x apparently a guy cut his frame to make it fit 😂 but I definitely don't want to do that.

@Trikekid84

Жыл бұрын

I also tried to find a oem xr200 intake, but couldn't find much. I'm not sure the part number on mine, it's a generic 30mm intake on ebay. Clamp style on the carb side, not the two bolt flange style like stock.

@Trikekid84

Жыл бұрын

I'd still say the 28mm china carb is well worth it for $30 if you have an exhaust.

Is there anyway that you could give a rough estimate on how much it costed you to rebuild your motor?

@Trikekid84

3 жыл бұрын

With doing it myself, and help from a guy I know, $400. crank was rebuilt for $75, piston and ring kit was $110, timing chain maybe $20, I re-used the valves, I had them re cut and seats re cut before this rebuild. Machine shop might charge $40 for that. Gasket kit was $36. New clutch parts were $60. Oil pump assembly $100, I'm probably forgetting something.

Where do you recommend buying a spark plug wire for one of these? Just got me a 1985 atc 200x from a friend for 100 bucks!

@Trikekid84

3 жыл бұрын

The wire screws into the coil, and so does the spark plug cap. So it's just a regular pice of spark plug wire, (not part of the coil like on other thibgs) so you should he able to find on easily. Honda dealer, used coil on ebay or something will have one on, atv junk yard.

@lingyguisar4149

3 жыл бұрын

@@Trikekid84 i got the wire but not the spark plug cap... The wire on the ATV has two wires not sure how i would connect a spark plug cap. Help? Thanks man I'm new to the ATV game. Lol

@Trikekid84

3 жыл бұрын

@@lingyguisar4149 not sure about the two wire thing, one wire plugs into the coil from the harness, and another one grounds to a coil bolt. And the spark plug cap just screws onto the end of the wire.

I bought an 84 and 12hp with me on it just is a little low I mean it still rips but the towards the top she’s hurting for power and I just want a little more like 2-4 more hp what would you recommend because it’s going to be a trail bike and I need reliability

@Trikekid84

2 жыл бұрын

Taller gearing, and a bigger carb will put more power to the top end. I feel like exhaust adds power on the whole curve but bigger carb and exhaust will help. Next thing I'm going to do is get a web stage 2 or something cam. Should add more top end but also more low end. Should also set my timing so it's dead on.

@winterholdsguard1977

2 жыл бұрын

@@Trikekid84 cant u set your timing manually? why wont it set correct?

what size is your front tires

@Trikekid84

2 жыл бұрын

23x8x11 I believe.

Nice bikes. What size jets are y’all using?

@Trikekid84

3 жыл бұрын

Cant remember, its ether a 112 or a 115 main, i know I have a 42 pilot. My intake boot ripped, found a new one, its really a 30mm intake. Had to file the holes so it would fit. Dang china parts haha. After all that it runs really good, starts good, plug is brown!

@keshawndavis

3 жыл бұрын

Haha thanks

@keshawndavis

3 жыл бұрын

Do you know the slot you clip is in on your throttle needle? And how many turns out your fuel screw is?

@Trikekid84

3 жыл бұрын

@@keshawndavis my mix screw is 1 1/4 turns out. I originally had it jetted too ritch with the stock carb, it would stumble like a rev limiter, but I wanted a bigger carb before I changed my jetting. Samd thing happned with the new carb so I leaned it out. Lots of trial and error.

@Trikekid84

Жыл бұрын

Took my carb apart today. 120 main, 38 pilot, needle clip at top groove, mix screw one turn out. Oko 28mm flat slide with the mystery needle it came with.

What jetting did Travis go with on his 200x with the stock carb

@Trikekid84

2 жыл бұрын

38 pilot and a 110 main I believe. We both have a 28mm flat slide now.

@neilbarnett1367

2 жыл бұрын

@@Trikekid84 ok thanks

@neilbarnett1367

2 жыл бұрын

Thanks just bought a 84 200x I want to put a Dg pipe on it did u have any problems putting the 28 flat side on them besides the intake

@Trikekid84

2 жыл бұрын

@@neilbarnett1367 nope it is a tight fit but it does fit and I can still pull up the choke. It's a OKO flatslide, uses Keihin jets.

I have a 200x and it will not idle low. I've tried everything. Any ideas?

@Trikekid84

3 жыл бұрын

check for air leaks by wiggling the carb up and down to see if the boot leaks, that's my problem right now with a bigger carb I had to cut my boot and zip tie it in two directions so it is more ridged. Can also spray gas around the intake and see if it idles up or down. If its not an air leak see how worn out the carb slide is, sometimes the idle screw will wear a dimple in the slide and it might not be able to go down all the way. if not that then make sure the throttle cable is returning all the way? If it starts easy its probably not an air leak.

@smokeybandit4910

3 жыл бұрын

@@Trikekid84 Well, it's 100% not an air leak. It was running fine and then all of the sudden it wouldn't start and when it did it would pop and snap and run pretty bad. It sounded exactly like a motor with the timing chain off a tooth. I tried to check if it was in time, lined up the cam gear but what am I supposed to see on the flywheel? Its also got pressure coming out the intake, it will blow a rag out and when I had the carb on it it would shoot gas out of it. The valves are adjusted perfect and it has 180 psi compression. It's exactly like the timing chain or valve train is off but I don't know how to fix it.

@smokeybandit4910

3 жыл бұрын

@@Trikekid84 There's also a spot when you turn the motor over where it will roll/rotate by itself. Not sure if that's normal?

@Trikekid84

3 жыл бұрын

@@smokeybandit4910 there are 2 Mark's on the flywheel, line up the T mark with the small hole in the stator cover, then look at the cam, the dot should be face up, and then you set the timing line up the flywheel to the F mark, which is about 10 degrees before the T (TDC) and then line up your cdi pulse rotor so the line on the black box lines up with the line on the mechanical advance thing. My friends 200x jumped one tooth and it had the same symptoms, wouldn't start. Before you even set cam timing re tighten your timing chain by removing the 10mm bolt from the adjuster, thread in a m3 bolt into the adjuster, pull up on it to tighten the chain when the 14mm bolt is loose, then re tighten it. There is a video on this by D Ray's garage.

@smokeybandit4910

3 жыл бұрын

@@Trikekid84 okay, so line up the cam gear dot and pointer up while the T mark is visible visible in the inspection cap? Thank you so much for your help, again this is my first 200x and I've never had this problem before so it's my first time digging into this