Hornby be shivering in their boots

@SamsTrains

11 ай бұрын

hahaha!

@musiqtee

11 ай бұрын

(Sort of) seriously… Companies like Hornby should now “embrace” the changing situation. Any good (any left…?) board member would demand that of their CEO. They could make SO many parts available for sale, like couplers, wheelsets, motor-controller-chassis assemblies, pantographs or LEDs with optical attachments… Next step, 3D files of more models than they themselves couldn’t or wouldn’t produce in the far East. I’m nuts? Maybe, but our economy is way worse... This would be a fantastic “local” opportunity, and I guess a small tad better ecologically too (less logistics). When “made in the UK” is history anyway, why not “designed in the UK - made by our community” instead? Best of luck (from 🇳🇴) with forthcoming designs and prints! 👍

@kenjimaurerfromdisneyland2001

11 ай бұрын

@@SamsTrainsHappy surprise day!

@generalprincecodyhedgewolf2944

11 ай бұрын

Hornby stinks at making full details

@Somestupidity

11 ай бұрын

@@generalprincecodyhedgewolf2944 What models have youve been buying then?

The reason the bottom looks so wavy is because it's very difficult to resin print large-ish flat surfaces parallel to the build plate. If you would tilt the model around 35-45 degrees or so, it would greatly improve the bottom surface (but since the print is higher, it would take a little longer to print). Cheers!

@thebritishengineer8027

11 ай бұрын

I can say with some confidence I know what I am doing with 3D printing and have a “turbulent” history with this actual machine. You can print large plat surfaces off the build plate, as I produced 5th wheel covers for 1/14 scale RC trucks about 2.5" diameter and precise chassis rails for 1/76 to 1/35 vintage lorries. The issue sadly is a fault with the Saturn 8K, the arm of the printer bends exacting about 40 newtons return force on the fep that causes really bad elephants foot/distortion. I have compensated, but it's not the answer. Solution, I need a better constructed printer to handle that kind of work. Oh the printer is very good trust me, my 009 quary wagons it is said are better than anything else available the printer good enough to produce exact brake gear and GWR above the axle box's.

a few suggestions 1. get a pair of silicone rubber trays, sit the printer on one and the wash station on another, this will protect your desk from resin drips 2. get a few disposable foil platters (party aisle of the supermarket), perfect to stick the build plate on while removing stuff, again saves mess 3. grab a pack of kitchen roll or blue roll and keep it to hand 4. when you take out of the IPA, drop into a jug of warm water to rinse the IPA off (makes it easier to handle and stops the IPA fumes filling the room - also when you have supports will make removing them far easier) 5. for most parts air drying is fine, for anything with large flat plates let it dry overnight before curing, this can help if you find parts start to warp 6. that wash station is too small, that is for the smaller Mars 3 printers, not a huge problem but with the larger ones you can actually stick the build plate into the wash station, which will clean the uncured resin from that as well Saturn 2 is a lovely machine, larger than the one I have here but I know someone with one good luck and enjoy it

A couple quick tips from someone who learned the hard way. Even after washing the print, use gloves to handle the uncured piece to avoid resin on the skin and finger prints on the print itself. The flexible plate makes removing the print much easier, I've only had to use the putty knife on thinner prints. Also with the flexible plate you can drop the plate and print into the cleaner if the print doesn't pop off right away. You just need to clean the bottom of the print when it does pop off after washing. Someone suggested a silicone tray, I use a silicone electronics desk mat for my prints and around my work area, it help greatly for cleanup. And lastly, I bought the suction handles to put on top of the cover for easy removal. Eventually you will grab the sides of the cover with resin on the gloves and ruin the cover, resin doesn't come off the cover at all once it's on there. Enjoy!

Great that you started with Resin printing eventually Sam 👋👋👋 Just an important tip from us; after poring the resin into its basin for printing, wade the spatula tool through the resin softly to remove all air bubbles, otherwise bubbles (or what's left of them) can ruin the print, especially at the starting point (bottom). Resin printing is fantastic. We've seen actual manufacturing grade made wagons from it 🙂 Bon chance with what's to come 💓 Cheerio.

@leonkernan

11 ай бұрын

I normally raise and lower the bed a couple of times manually before starting, that seems to agitate the resin quite well

@pesto12601

11 ай бұрын

Once a resin is created that won't kill you everytime you go to print a part, it will be good for folks to use. Until then - it is just too dangerous for the average joe/jill to go off and use but folks continue to do it anyway! Saw a video recently where a hobby crafter was using a cheap laser cutter in her bedroom to cut out stuff for scrapbooking.... had no clue that the fumes from the laser were TOXIC!!

@leonkernan

11 ай бұрын

@@pesto12601 it's not so much the laser as the stuff that it's burning. People forget that a laser isn't a pair of scissors, it's actually burning material away.

@pesto12601

10 ай бұрын

@@leonkernantrue... but the laser itself is dangerous too... it can damage your retina very easily!

Coming from a Printing Trade (Lithographic or Offset, eg. Ink on Paper) The Advances in this Tech are just mind blowing. Amazing that a Set up is Available for the home Hobbyist. Truely something I could Barely Imagine in a Factory Setting in the Late 1960's, let alone @ Sam'sTrains knocking models out in his Loft in a few hours. It's just Mind Blowing..! And Sam, you seemed so Calm Unboxing, Setting up and Working a New Tool or Tools. That did cost a Few Quid to be Fair..! Well Done Young Man. An Impressive Performance..! Cheers All. A Luddite in Oz. 😎

@kennykd97

11 ай бұрын

Advances! mate this style of printing has been around since the 1980's.

@gs425

11 ай бұрын

​@kennykd97 Yes qw were using laser epoxy prototyping back in early 90s. However I think what this chap means is that its advanced to home use. Well it had done about 5 to 10 years ago. Sam has just caught up...partly due to his fume concerns

@kennykd97

11 ай бұрын

@@gs425 It became so cheap because the patents ran out mate then China started mass producing them and trying to outdo each other competition is king.

Thank You. You are the first person I have run across that has taken the time to show how 3D printing works. Very informative.

Wash and cure machine isn't necessary but it makes it 1000 times easier!!

@SamsTrains

11 ай бұрын

Absolutely - I'd be lost without that! Thanks for watching, Sam :)

Wrap the washing basket with wire mesh to avoid losing smaller parts when washing the prints

Looking forward to seeing what you can make with this! I had the same issues with bottom layer sinking and separation until I started printing things at an angle and getting the support systems figured out. I've also gotten my best results by making it so only the supports touch the build plate and keeping the actual part off the plate entirely, eliminating the potential "elephant foot" that can develop on those first layers.

10:02 Yup, that's my reaction whenever I get to pull off a protective film. Lol

Great to see you using a resin printer, I use a Saturn and found it’s best to print the models at an angle and also make sure the resin is at about 25 degrees C. I avoid touching the prints until after curing as the ipa will contain resin. It’s a learning process, but stick with it!

This is amazing, great work! I just hope the fumes don’t end up harming you.

Ok this is serious someone call the emergency services Sam's got a 3d printer addiction 😂😂

Thanks, Sam. I've been "shopping" / researching a resin 3D printer as a replacement for my now ancient filament machine. This demonstration has convinced me that the two piece printer and curing machines are well worth it. Oh, the better resin is also a win. Thanks again for all you do - and SHARING it as well.

I can’t wait to see what you’re able to make with your new skills. You could improve your existing models or make some wholly new locos. I’d love to see more Great Eastern Locos made by you, or if not some Great Central, LSWR or Lancashire & Yorkshire designs.

I'm about 6 months ahead on this journey. Some things I have found. The flex plate is a massive plus, especially to prevent damaging parts. if doing small parts, put several with their rafts touching so the Flex works better. It is not always necessary to use a raft and print at an angle if your part has a flat side and no huge overhangs. Having said that shifting the angle around can sometimes improve print quality, at the expense of time and support material. When doing shells, (working on an EMD F9P to make PAN AM #1 & 2 ) I have found that adding temporary internal cross-webbing will prevent a lot of warping, and thus failure. I was hesitant to start resin printing because of the "toxicity" but it is not like instant death if you inhale it, still avoid it but a fan and a widow are enough, I don't think you need level 3 hazmat.

@AmateurCz

10 ай бұрын

Resin is cumulative poison like heavy metals. When you notice some effects, it will be to late. At best you will get allergic reaction when you approach the area contaminated by resin. Other options are kidney, heath or lung failure, loss of eyesight or neurological issues. These machines need enclosure with fume extraction. Wear full face mask when opening the enclosure. UV resins are not safe even when cured. Prints need to be sealed or they will continuously off gas small amounts of toxins into the air.

Nice to see you trying some resin printing, been loving my Mars 2 Pro for N Gauge printing, but have had to upgrade to the Mars 4 Max since it's build plate is nearly the same as the Saturn's (it's also cheaper), though I do recommend using some thicker gloves like some Marigolds or the like, the ones which come with the printers never feel thick enough heh I do also recommend getting a cover to block out the light when it's printing, might not seem like much but has helped with the quality of my prints. Anyway hope you enjoy using the printer! ~James

Can't wait to see the fantastic stuff you'll be able to produce with this.

Very impressive Sam! No doubt you’ll be printing out some of your earlier models to compare against. Looking forward to seeing future developments as your skills improve with this next level of printing.

Excellent video Sam! Looking forward to all the impressive things you’ll make with your arsenal of 3d printers!

@PaulinesPastimes

11 ай бұрын

I completely agree. I understand the process much more now. 😊

You could install a cooker extraction hood over the printer. One that has a carbon filter. It should help to get rid of any fumes that escape.

@johnfiott

10 ай бұрын

Do they have sufficient suction power?

@awatt

10 ай бұрын

@@johnfiott They get rid of cooking fumes so yes

This is fantastic, it looks much more accurate than PLA 3D printing and I can't even see the layer lines! I can't wait to see what kind of models you make with this.

Impressive video Sam! Incredible detail! Would you ever be interested in getting a laser cutter? I've used them before and they're really intuitive - they're fantastic!!

@SamsTrains

11 ай бұрын

Thank you! Yeah I like the look of those too! :D Thanks for watching, Sam :)

@Theworldasitistoday

Ай бұрын

Hello. What software do you use for the design of the models? Thank you.

@timbervalleyproductions

Ай бұрын

@@Theworldasitistoday For 3D printing? Id recommend SketchUp free which is what Sam uses (but he has a license as it's for commercial purposes)

Hi Sam, timely video as I am just starting to get into 3D printing for my layout... Using an FDM printer! I soon discovered the drawback of this - usually reliable printing process - when I came to trying to print some tiny N Gauge cars!!! Resin is definitely the way to go and something I would be looking into for these small model railway accessories. Good video 👍

It almost looks like injection molding Without that seem line through it The only locomotives I know that don't have the seem line through them. Are the proto 2000s

@SamsTrains

11 ай бұрын

Exactly - it's capable of all the detail of injection moulding without the complexity! You lose the capacity of moulding, but you don't need that anyway! Thanks for watching, Sam :)

Resin is amazing to print modeltrains, doing it myself too!

@SamsTrains

11 ай бұрын

It really is! It's quite finicky to print stuff... an awful lot of hastle, but worth it for the detail! Thanks for watching, Sam :)

Great video Sam, thanks for making it and sharing it.

It's good to see you give resin a try, better detail and so much faster owing to only having a Z axis move. One model or a whole build plate takes the same time. Great video Sam, thanks.

Bonjour Sam. Nice test and very instructive. I have not made that step towards 3D Resin printing (and 3D printing at all) because, just like you, I was looking for a technical update around resin products. Some weeks ago I have understood that there are now water washable resins. Elegoo does provide such. It removes the need of the IPA for the washing process and it even seems to remove the need of the cure machine at all. This now definitely sounds interesting and appealing! 😊 Cheers.

I got a 3d printer a while ago from Elegoo too! It’s pla, and the fact that most of the parts on their filament printers are interchangeable is amazing. Now I can 3d print what ever the heck I want to again!

Fascinating!! When you're completely up to speed with the device it would be interesting to try a head-to-head comparison print of the same file on filament vs resin

@simontopley4771

11 ай бұрын

Yes, I agree, like for like, I'm looking at starting printing, but which is best all round? If these smell as bad as I've read, there will be ventilation requirements to consider too.

Huzzah!! good move Sam. You'll get some great results with a bit of practice. I had a hard time printing Gladstone with my Elegoo Mars II. Different printer, but tricks I learnt were; lift the project off the plate. Even by 3mm will make a difference. The resin spent on supports will off-set resin wasted on failed prints. And add as many additional supports as you can to the straight edges nearest the print plate to get a crisper edge. Enjoy!

Hi Sam, I'm so glad, seeing you read the manual first, before working with your new equipment. Not like these stupid people, who think that it's a proof for intelligence to throw away the manuals and then spill the net with their stupid questions.

I've been in the market for a new 3D printer and I was dead set on a certain FDM printer that I was just waiting to come back in stock, but this video convinced me to rethink it. I didn't know about the plant based resin and the fume issue was my main reason for never diving into resin printers. I've always wanted one since I am mostly interested in miniatures but I've just never had anywhere to put one.

@babbagebrassworks4278

9 ай бұрын

Yep, first vid I have seen about plat based resin, getting friendlier, soon there will be no reason not to get one of these.

Very interesting and informative video, Which helped me understand what's involved in getting started in Resin 3D printing and with using this machine in particular. The plant-based resin seems a lot safer and produced great results - a definite plus. Thanks for another great review!

Always willing to try something new. I cant fault you Sam. Great video. You make it look so easy. All the best.

Sam, I find the water washable resins also have less fumes than the other resins. However, I do find it warps more than other resins.

Hi Sam. £475.99p.... WOW! Just think, for that price you could have purchased a small Bachmann or Hornby wagon that is ready made. Paul. 👍❤

@modelrailfan37

11 ай бұрын

Lol, maybe a little more than that, but you could definitely get more out of a resin printer than what you could buy from the model rwy market for the same price.

@ReggieArford

11 ай бұрын

Of course, you still need to buy the wheelsets. And if it's a loco, the drive mechanism.

@modelrailfan37

11 ай бұрын

@@ReggieArford I mean, you would need to buy a motor and wheels, as well as wires, but you could print the chassis and gears.

Finally! 😂 Well done Sam and welcome to the fun, frustrating world of resin printing. I would suggest buying a screen protector ASAP. Any spills on the screen will knacker it, so it's just added protection. Also the flashdrives sent with these machines are crap and tend to fail, missing sections of your sliced file. I have always bought replacement branded drives (sony etc) but you need to keep them under 16GB or they may not work. Another tip is fit a kitchen roll holder on that beam next to your printer. You'll want it ready for emergencies (which will happen!) have fun. Tom

Resin printing is great for detail! If you ever need to fix anything just use cyanoacrylate glue more commonly known as super glue. Make to place supports for your models sensibly as well. Good luck and happy printing!

More of this please Sam. Very interesting & instructive.

Resin printers are a complete game changer for fine scale modelling, the detail you can achieve is impossible with any other techniques. Once you get some experience with this you won't look back, next you need to get experienced with some 3D CAD software so you can push your own models to the next level.

Great video as usual, so just ordered mine, looking forward to printing my own 3D models soon, once again very informative video. I was sitting on the fence as to buying one, also ordered the same plant based polymer

Finally! 🤣 You might want to get yourself a big silicon mat to work on. It makes cleanup way easier. eSun makes a plant-based resin that works well too and (at least where I live) it's a lot less expensive. Make sure to do a couple of exposure tests to dial in your settings. Different resins can need different exposure. You will not regret getting a resin printer, unless you drop resin on your carpet. 😁

I saw a video the other day that was talking about a new vat purge feature in the newer ones where you let it settle and it purges a sheet print that traps all the contaminates and you just peel them off the build plate, seemed a prety cool eay to clean up after watching people screen their resin for years

Welcome to Resin Printing Sam! I have the Elegoo Saturn 8k which is a superb machine. One tip I would like to offer is check your print bed is correctly leveled every 10 to 12 prints, as in my experience the level does change. Might not affect your machine as it is newer, but its worth keeping in mind.

@TheRip72

11 ай бұрын

I level my Anycubic Photon before every print because scraping the prints off the plate moves it slightly. Thankfully, levelling is a quick & easy process though.

Printer seems great - don’t even need to add paper!

@SamsTrains

11 ай бұрын

haha exactly!!

Really useful Sam, thank you. I have been considering purchase of a similar machine to produce D&D miniatures. Now feel more confident to do so. Much appreciated!

Take this advice with a grain of salt because I have no experience, I would recommend that you get a larger curing station just in case you want to make something crazy like a big Pacific or Northern (4-8-4) I give this advice just because I would personally like to see you make the GWR Great Bear :) That wagon looked amazing. Can't wait to see what kind of locomotives you can produce with that thing.

So many amazing British euphemisms and jokes in this video, but my personal favorite was "Right, so, I've allowed my parts to air dry for a little while..." 😂 love your channel Sam!

@JP_TaVeryMuch

11 ай бұрын

What a man gets up to in his attic is between him and the spiders alone.

This looks like a usable system, I'm looking forward to seeing it used in the coming videos. God bless

Glad to see you are experimenting with resin. I think you will really enjoy making your next locomotive; using the resin printer for the details and the filament for your structural parts.

Yay! Do excited to see you print on this. I vote Gladstone!

I print O-Gauge 6 wheel GNSR carriages on my Saturn S

Amazing piece of kit

@SamsTrains

11 ай бұрын

It sure is! :D

Hey Sam! Awesome to see you've picked up the resin 3d printing bug. I've only ever used resin myself and have found your videos on filament printing to be super enlightening, so thanks for that. :) I have a few tips that may help you with a few things here. It's good practice to get a protective surface for your bench, so that when you remove the models off of the build plate you're not risking getting wet resin onto the wood top. It's a real pain if it seeps into the surface. You can cure the stain with a UV lamp but then you've still got a tarnished bench top. You can just grab a rubber mat for this, there are loads of cheap ones you can grab that are marketed for putting under pet food bowls. They work a treat, and the UV resin doesn't eat through them. In terms of ventilation, even though you've gotten yourself safer resin (something which is often a dubious claim by the manufacturer so watch out for that) I'd still say try and work in a ventilated space. If the resin doesn't make you dizzy, the IPA will. In my expieriance the IPA is actually the worse offender in this regard, and having just managed to get the full setup going in my shed with newly installed cyclonic ventilation, I can't sing it's praises enough. In terms of that sagging on that print you made right at the end, extra supports will only kind of help.... kind of. You will ultimately find that no matter how well that section is supported, you'll get sags between each support. The issue is you are printing a flat surface parallel to the build plate. As the printer goes to print those initial flat layers, it has very little support bellow them and struggles to make that area solid, hence it sags. By printing the whole model at an angle, that flat section builds up gradually, and each subsiquent layer is supported by the slightly smaller previous layer. Yes, this means you will have to learn how to properly support models, but it's well worth it. Once you get into a good rythm setting up supports and knowing what to expect, the whole thing runs very smoothly, so it's worth putting those hours in. Sorry for the long response. Not trying to be that guy in the comments that points out all the errors in a video (trust me I've dealt with that nonsense myself far too often), just wanted to offer some help as you've been super informative for many things I've persued in the hobby. :) Happy printing!

@SamsTrains

11 ай бұрын

Thank you so much for the help Nick - this video was shot on my first day with the printer, and it was actually a couple of months ago now! I bought a mat very quickly, and have been using that. I really didn't want to print at an angle with supports initially, as obviously that can double print time, so I tried everything to get them to print flat... obviously that was no good, and I now do print at an angle... I had to find that out for myself I guess! Thanks again, Sam :)

@HairyNick

11 ай бұрын

@@SamsTrains nice. I dread to think what video footage of my first day with my printer would have looked like...

I think it is always level because the surface of the liquid resin is always level. So as long as the printing platform is close to level, then all is well. Another thing. When I was in the Canadian Armed Forces we had gas-mask training. The mask had a canister of activated charcoal which worked very well to remove the horrible, stinging tear gas from the air in the practice hut. As long as you got your mask on quick enough upon entering the hut, the only parts that got stung were the armpits and the unmentionables. Love your vids. Cheers from Canada :-)

Excellent video with very interesting detail information thank you Sam

Very interesting. As an impatient TT:120er, this definitely looks very promising to me!

Thanks Sam, I am glad you've gone for Resin 3D printing, the quality was superior to ABS rod version. Plus finding a low odour resin too for me it was an issue and I am sure it was for a few others. This will encourage people who were reluctant to enter the 3D modelling world to now do so!

1:12 lol. Now who would ever do that.

@SamsTrains

11 ай бұрын

haha you never know!!

Sam’s Trains Productions is expanding so now we can get 5x more balancing train cars XD Man this looks awesome Sam. I can’t wait to see what projects you tackle with this new printer

In the late 90's I was designing consumer goods on 3D CAD and prototyping parts on SLA machines costing £hundreds of thousands. Part cost alone was at least in the £100's even for small bits. Amazing to think you can buld a full setup of printer and wash/cure station now for under £1000! Makes me want to crank up my ProEngineer CAD system again! (£6k for a basic software licence back in 2000's minus all the add on's!).

Thank you Sam! Really interesting

Congratulations and welcome to the club!

good vid on the channel sam keep up the good vids thanks lee

👍👍Riveting . New chapter, so looking forward to this future .

Superb ! I'm in to buy one. For the price of two Hornby/Bachmann locomotives (or 1 Heljan 1/2), that's an amazing tool ! Like with my laundry, I can put it on one of my balcony while in use, that solves the smell problem (except in winter and while it's raining). You will certainly do extraordinary stuff with those tools !

I’ve been printing locos and wagons on my original Saturn for a couple of years now. With a bit of effort in setup you can get awesome results.

When placing the fill on to the printer, give it supprots and turn it to 45%, before you print, build it on a raft plate first. The way you don't have a large amount of pull on the model,which can course the model to stick hard to the fep or build plate. Also you end you with it sticking hard to your build plate. Also your end you with less fails and a better model. Had mine for three years now and it on of the best bits of kit i have ever got, taken my modeling to new levels. An other tip when taking the supports off is to use hot water your find the supports will just fall off, do this before you cure the model after you washed it

Is there a better area that you could use for the resin printer, that would allow better/safer ventilation?

I'm glad to see you've finaly invested into a resin printer! I have an Elegoo Saturn 2 and sell model London Underground trains on eBay

Resin printing is amazing, I do scale models too and I can print batches of highly detailed individual tank tracks with all the pin holes perfectly formed for joining them, and also tiny details and mesh stowage baskets and the like... It's a great technology to come to a consumer level! Enjoy!

Interesting video here Sam , some decent models there.

Great video Sam! I do worry about the fumes and ventilation in your train room. So be careful and aware of that.

The next step on Sam's maker journey will be a laser engraver/cutter, im calling it now :D

I worked for a company that offered hearing aid shells made with resin printing. if the shell was very thin, they seemed more brittle than the polymer shells. we also used a clear coat to make the shells thicker if needed (UV cured). We did not do the printing.

For washing: even if you let drop off the print carefully, there still is a lot of unvured resin on the print. So the isopropanol gets saturated quite fast. And the box of the washing mashine isnt'so easy to clean. So I optimized the cleaning process by using 3 containers extra: first to pre wash, second to pre wash again, third is the container of the washing mashine and forth is to "cure" saturated resin in the sun. After about 5-8 prints I swap: 1st container is put into sunlight, so the resin get hard and fall out of the isopropanol. Second pre-wash iso becomes first one, and the iso from the washing mashine is used for the second pre-wash. The washing mashine is filled with the Iso I cured in the sun and filtered, + some fresh isopropanol. This works great.

Good luck with your new peace of kit 👍😊🤩

22:40 yours came out much better than mine Sam. I think my resin 3D printer was faulty and I had to send it back, that happen about 3 month ago. Cheers Jasper & Willow

Great video sam 👍 looked a bit of work at first but when you got going it seemed very simple for you 👍 😀

Cool to see you jump in here. I was hesitating because I really need resin for TT but I think I might jump in now that you have made the move

Fantastic video as always! Do you have plans to have a comparison video between this and your older, non-resin printers? I'm really looking forward for some better detailed rolling stocks - especially your own locomotive designs - produced with this new printer. Cheers!

Wooo less goo , more awsome loco making

What a useful video! You explained the process really well and answered a lot of my questions about resin printing. Unfortunately one difference from an FDM machine I suppose is that you cannot really see if the print is going wrong in order to stop it early. It would also be great if we could get to see a video of you spraying the resin models later on (assuming you do this). Thanks again.

Well done Sam my youngest son has a couple of 4k resin printers and it did take him a while to get all the fine tuning done so just be patient

Hi Sam, finally got around to watching this video. I have been printing with resin for a while. I also run a Facebook group ‘3D printing for beginners- model railways’ so was interest in this video to share link on my Facebook group. Yes you have quite a bit to learn but in time you will. I have gone through several types of resin from not that nice to what I use now, definitely worth looking at the water washable resins. I also find that it’s best not to use a lot of different types as each type needs different settings, transparent resins have different cure times than non transparent resins. With this in mind master one type first, personally I mostly print with grey resin and using just one type I get consistent prints. Good luck and look forward to future videos.

@johnfiott

10 ай бұрын

Is there is such a thing as "excessive curing time" though?

Nice one Sam well done.

Blimey, that's a lot of effort. Good luck with it.

Finally you did it!

This is awesome, exactly what I’ve been wanting to try. Thanks for sharing your results Sam! Anyone know of a good place to find files for printing things for model railways? Whether it’s a free or paid source?

You have given me an idea. I have scratch built a wooden wagon. I wonder if I could scan it and then make like 20 copies? A bit of paint, wire grabs and decals and it would be done.

I can't wait to see what you'll be making with this printer Sam :) Cheers Jasper & Willow

in your head turn the model upside down and look for areas that may pool if water was poured over it. This will happen to the resin so angling the print or leaving drain holes will cure this. The cutters are for snipping off support legs if you print that way.

Sam how many 3D printer's do you have in your train 🚆 room now/ AKA your pride and joy?????

Just curious. Do you know what the main difference is between the 4K and 8K versions, other than price and maybe soe ultra fien detail? I am just not sure whether there are enough benefits of 8K to pay the extra price compared to a 4K model. Thanks for another great review and unboxing

Well done - look forward to same actual Prints!!! 🤔🚂🚂🚂

I have a Photon S that I’ve yet to use as FDM has got me 90% of the way without the hassle of resin, but my bigger concern is long term durability. I’ve bought kits from others with resin parts that are about as straight as a corkscrew, and the other issue is fragility that gets worse with age, had a little accident with a small loco body on a Hornby peckett chassis and it blew into a million pieces, as well as suffering with cracks when hand drilling holes for handrails with a pin vice. Also bought some unpainted figures made with resin for the railway, detail is amazing but several lost their feet before they’d even seen a paintbrush!! It would be good to know if any resins, for instance the plant based one, prove to be more rugged?

Liked and subscribed on this first video I’ve watched. I have filament and resin printers and they both produce viable items depending on the requirements. I do like the higher resolution of the resin printer though. I’m looking to use it for making replacement parts for die-cast models. Good luck with your printer. I’m looking forward to seeing what else you produce. I use the water-rinsable resin.