I’m glad you made this video I was thinking about getting one and I’m surprised holly normally makes a great product

also you need a dyno tune with this intake, it changes the velocity of the air going in. A canned tune isn’t going to compensate increased air gain, without proper fuel mixture.

Glad to know, I was thinking about getting the intake myself but I guess I'll go with 6.4 intake.

@NickHerAmerican

7 ай бұрын

Edlebrock intake is goated for mopar

MMX knows this problem, now they sell these machined, which takes a away those square gaskets and they make a custom gasket. Which I purchased. You should send yours in to get machined. Ask for Robert ext 110 at MMX

@neverenuff2381

4 жыл бұрын

Good to know but it's too late. After waiting 6+ months on Holley, canceling the order through them, locating one on eBay, installing and it still goes South. I sold it as soon as I pulled it off. Any luck with yours? Are you nitrous/boosted?

@nickrichmond1978

4 жыл бұрын

neverenuff not yet I’m doing my install very soon. Along with the intake, I’m doing my cam,hellcat Tb, I already have kooks LT w/mids, blaster coils new plugs LegMaker CAI & GTHAUS exhaust. Trying the diablo tune 1st see how it goes. 396 stroker kit next.

@neverenuff2381

4 жыл бұрын

@@nickrichmond1978 wow your build moves fast! I'd love a stroker short or long block but it'll have to wait. Gotta let me know how the Kooks LT's and the LegMaker CAI work out. I've been looking at longtubes just for the exhaust note alone.

@nickrichmond1978

4 жыл бұрын

neverenuff I have the kooks already installed, they are awesome. I couldn’t decide between them or American racing but in the end kooks was it. My legmaker won’t be here until early June. But my AFE momentum works great too. Buddy of mine is buying it from me for his Durango. Get kooks!!!!! You won’t be disappointed.

@cwilsongas

3 жыл бұрын

All you had to do was take the old gaskets out ano put them in your new intake manifold.clean them up first.

I been thinking of going with a Holley as well. My mods are long tube headers, ported,intake and nitrous. You say this thing looses torque at low rpms? Would it still be worth getting sense I’m spraying nitrous which helps with the torque?

I have never seen the intake or fuel rails in person so this is just a guess, but looks like the fuel rails was made to fit tall or short injectors. Looks like the braket that is on fuel rail can be loosened and rotated 180 degrees to fit whichever injectors you have.

@neverenuff2381

3 жыл бұрын

Might be the case for the Passenger side, however, the driver's side rail will hit the oil fill tube. The Michigan Motorsports spacers work great, excellent fitment and zero leaks.

Saw in another video a set of adapter plates for this

Nice car man. I have a 06 daytona charger with a torqstorm super charger I was going to use the holley sniper on mine now I wonder, however I have seen one piece intake gaskets that fit better being 1 piece per side but not sure of brand name 1 piece will seal is your 5.7 370 hp stock? Other thing is the sinper holley intake is not a big change but adds about 8 hp through the torq range of your motor! Keep your head up and the video coming also was the canned Diablo tune you used the 93oct. Did you have to use the injector extensions for your intake swap,thanks man. Mike

What about using the 6.1 paper gaskets? Would that address the issue with the gasket channels? I saw one of your responses below about the sniper pulling really well above 5krpm. How was it below that?

@neverenuff2381

3 жыл бұрын

The 6.1 gaskets would probably work, I didn't have any on hand at the time. From what I experienced, It started to shine above 5k, definitely need a higher stall torque converter and upgraded valvetrain to enjoy the manifold (stock is limited to 5800).

At this point you might as well just get the 392 manifold and a module for the active runners. I’ve seen dyno results of 20hp increase from low to mid rpm and 15-20hp at the upper end.

im wondering if the gaskets blew out from not having a breather and pcv in the valve covers. getting ready to do my install with the sniper intake and valve covers. already tapped the covers for pcv and breather. by chance do you know if the car and truck 5.7 injectors are same height? i don't have those spacers you used but i may get them for just incase.

@neverenuff2381

4 жыл бұрын

I'm not sure if the truck injectors would work. The spacers that I used worked great-no leaks.The failure that I had was the shallow depth of the groove for the o-ring.

Wow you found someone to tune a diablo pcm congrats. I gave up on holley/diablo for the 6.4 intake manifold as well as the intune i3 handheld programmer and pcm. So much easier to find a tuner that uses HP

@neverenuff2381

2 жыл бұрын

Late follow-up but man, I need to go to HP tuners, car hasn't been running right. If the culprit isn't the O2 sensor I had to lengthen on the drivers side to swap in the SRT manifolds, I'm switching over.

I was thinking of getting this intake for my cammed 2010 5.7 that I’m adding nitrous to next month. I was wondering is this a good setup to go with, or should I go another route?

@neverenuff2381

4 жыл бұрын

Not a bad manifold but like Nicholas R said below about MMX machining them for gaskets. Other than fuel injector spacers and making sure you have the dual bolt pattern for a factory style throttle body. After install it pulled pretty good after 5k RPM. It would be better with boost or nitrous since it shouldn't blow out.

did you ever get the holley intake to work?

There’s always an problem with Holley products. I’m having a problem with the Holley fuel rails fitting my 6.1 Hemi intake

Why couldn't you use the gaskets off the stock manifold

Recommendation on intake manifolds and throttle body for my 2021 dodge charger rt 5.7

All you need is a sheet of quark gasket and cut the holes yourself. Then rtv sealant on both sides. That will stop vacuum leak/ gasket blow out

@john-markbeard1552

3 жыл бұрын

Nah.. He's gonna go the stupid route ROFL

@john-markbeard1552

3 жыл бұрын

After he goes to all the work of porting he's back to making a gasket anyways. You can't fix stupid

If they retard the cam about 3 degrees on the top end you should have broken into the 39xwhp range. That 392 cam is great with adjusting the cam timing

Did u change out the springs ? And lifters or just cam itself

@neverenuff2381

3 жыл бұрын

Just the camshaft and valve springs. Kicking myself for not doing the Hellcat lifters while everything was apart.

Can you send me a link for the injector spacers I have the same one but back but I just found out I need spacers to make it fit

@neverenuff2381

4 жыл бұрын

Michigan Motorsports 56300

Would you recommend this manifold over the 392 manifold? I plan on getting one, whichever one can put out more horse to be specific

@neverenuff2381

4 жыл бұрын

I'll let you know, I ordered everything for the 6.4 manifold swap-stay tuned. This one needs work, I wouldn't attempt to run it out of the box. If you do buy one, talk to MMX as I'm told they machine it for gaskets. Great looking manifold for the price though and it was a shame I couldn't get it to work out.

Hey, do you have a list and website where to get all the needed parts for the holley intake?

@neverenuff2381

3 жыл бұрын

There are a few forums that talk about the swap, the big items you will need are fuel injector spacers, the adapter to mate the sniper fuel line to the factory pressure line, and the machined groove for the O-rings. I'm told MMX offers machine service for the Holley.

@patko1980

3 жыл бұрын

neverenuff its sad that Holley sends this out incomplete like that, I reached out to them asking about the seals and got a “what issue?” Response and now when I email them with other questions i get no reply. Poor customer service

@mikew6135

3 жыл бұрын

From what I saw you were trying to put the gaskets in upsidedown. The thicket end should have gone into the gasket ring channel. Thats why there are little tabs on it for pressure

Now with your intake manifold can you put a bigger throttle body on that one you put in

@neverenuff2381

3 жыл бұрын

Might go with the 90mm HC if my tuner can get it going.

I want to make sure everyone knows, this is because of the runners in these intakes, if your buying for a 6.1 srt build not a eagle or 6.4, you will gain hp and torque, also if you have a vacuum leak you will lose hp with sniper manifold. So maybe on a eagle 5.7 or 6.4 you will lose due to active runners but not on a 6.1 or stroked block non vvt.

@fknmonty

7 ай бұрын

What kind of numbers have you seen on a 6.1? I've been contemplating getting one of these for mine

I've heard that headers alone can add up to 30 whp. There's your extra 30 to make it to 400

@jmur3551

2 жыл бұрын

Not really. All about the tune you need more than headers to make 30 whp. Probably fbo gets you about 50 60

Do you have an lsd on the car? If so what gears? Nice car man!

@neverenuff2381

4 жыл бұрын

Thanks brother! I swapped in the Mopar 3.70 limited slip. If I did it all over. I'd go with the 3.09 as it's my daily. Definitely quicker off the line though!

@chrishemi5629

4 жыл бұрын

@@neverenuff2381 thanks for the replay man! Im still debading between the 3.09 and 3.90, id seen some 3.90 lsd for cheap, and i mean cheap 350 to 400 bucks! And every 3.09 its over 600 dlls, so im like should i just get the 3.90 or spend more on the 3.09. Its my daily so thats a factor too. Im not planing on spending a lot of money on mods, so thats why im considering the 3.90's, i want to get the best bang for the buck that i can get. Thanks again and ill be waiting for more videos! Keep it up!

How do you keep water from sitting on top of your block now that there is a open space under the manifold?

@neverenuff2381

3 жыл бұрын

I didn't have it installed for that long. But the Holley Sniper fits under the factory R/T, SXT hood.

@9891Daniels

3 жыл бұрын

@@neverenuff2381 I have a hood scoop on mine is why I ask

Most ppl port they 5.7 manifold or switch the 6.4 manifold im looking the 6.4 cam again. Im running the 6.4 intake manifold and the 6.4 corsa Cai closed box and my cai are about 5 to 7 degree difference the outside temp in va i seen where its been 75 recently and iat are about 80-81°iat and its been a 5-7 degree distance constantly and i only had it in week so far

@neverenuff2381

4 жыл бұрын

That's great news, any 0-60 times or dyno runs with it? I've been looking at the 6.4 manifold as people have good luck with it. Using this Mopar CAI, I'll see 3-6 degrees from ambient and 1-2 more with the Hellcat lower/snorkel but I have to be moving.. Might get some aftermarket heads next and see if the 5.7 ones are a choke point.

@aaronferguson47

4 жыл бұрын

@@neverenuff2381 not yet as i have to get new tires and it warm up some to test it i had it on bout 2 weeks now

@aaronferguson47

4 жыл бұрын

So im late to the party i have 6.4 manifold on with the corsa cai i still dont have the srv hooked up but the manifold is ported ill get a 0-60 soon may not yeild the best results because its hot out now like high 70's to almost 90's here in va

@neverenuff2381

4 жыл бұрын

@@aaronferguson47 Just ordered the 6.4 manifold and MSD window switch. Do I need anything else for the install?

@aaronferguson47

4 жыл бұрын

@@neverenuff2381 actuator wireharness and a cirkit boss unless using something different. Does your 6.4 manifold have everything else like 6.4 map sensor and the actuator motor

No vaccume leak issues with gaskets on intake?

@neverenuff2381

2 жыл бұрын

Yes, I definitely had vacuum leaks. Comment below says MMX has fixed the issue.

Hey whats your cold air intake Temps with that Mopar intake

@neverenuff2381

3 жыл бұрын

Man, they were low- about 4 degrees over ambient temp. It rains a lot where I live and the filter mounts low otherwise its a nice kit.

This is whp?

I have a 2012 Chrysler 300c 5.7 -stage 3 n/a TSP -Jba long tube -Catless midpipes Is it worth it? Should I get it

@neverenuff2381

3 жыл бұрын

Is it a DD and do you have/plan on getting a torque converter? This thing doesn't really move until 2500+ RPM from what I noticed. For all-out HP, I'd say yes but your trade off would be a loss in low end torque. How do you like the TSP Stage 3 cam? I may or may not have the TSP boost cam on order..

@susboat69

3 жыл бұрын

neverenuff I’m getting a 3200 stall

I just bought it for my ram 5.7 hemi hopefully it this don’t happen

Eek. Those dyno numbers are terrible. Just get the 392 manifold and a module for the active runners. I’ve seen the dyno numbers on that and it’s far better. 20+hp in low and mid rpm range and 15-20hp on the top end. Doesn’t look quite as nice, but the performance benefits are clear.

We’re you able to run your catch with the Holley intake?

@neverenuff2381

4 жыл бұрын

No, there weren't any provisions for the PCV valve at all. So I left the catch can disconnected.

FOR THE NEW VIEWERS, GET THE 6.1 HEMI GASKETS. THEY ARE FLAT AND WORK.

This mds 6.4 cam

You dont use silicone for intake gaskets lol this isnt a 1990 Chevy block Probably dont want silicone thruout engine

@neverenuff2381

4 жыл бұрын

I used a dab on each port, tried everything to make this thing work. Just ordered the 6.4 manifold though and should be in soon.

6.1 intake manifold?

@neverenuff2381

3 жыл бұрын

Not a bad idea at all, I've looked into it and for boost/nitrous applications it would be more than ideal. This is a d/d for now and the aluminum heat soaks from what I read in the forums. Checkout the manifold I finally settled on!

@chearchie4472

3 жыл бұрын

neverenuff that heat soaking is no joke...I also heard that 5.7 owners lost a lot power down low because the 6.1 intake is too much for the 5.7 without major supporting mods... it’s almost like a bigger tb on a stock engine...it’s too much to do any good

@neverenuff2381

3 жыл бұрын

@@chearchie4472 I hear ya, before I talked to Jay and got the revised tune, the 6.4 manifold ran warmer than the 5.7, I'm guessing its due to longer runners letting the air get hotter before it enters the cylinder heads. I'm going to remove it and install a heat shield and see if that helps lower temps. The 6.1 & the Edelbrock seem to be great for built motors or at least boosted with an intercooler.

@chearchie4472

3 жыл бұрын

neverenuff that’s exactly what I was told by other owners haha

@bayarea5.7

3 жыл бұрын

6.1 ported intake is what you want for full built motors, and I haven't heard any complaints from any 5.7 owners that have done this mod..all gains!

I have headers. Mid delete. Intake. Ported throttle body. I'm 417 to the wheels...stock cam. Why do a cam when it's going to boost you a few horsepower. Seems the cheaper way. Makes way less power. With a cam I'll be over 460 whp

@neverenuff2381

4 жыл бұрын

Cold air or an aftermarket intake manifold Tony? Those are good numbers, I chose the 392 mds cam simply to find out what Dodge was leaving on the table. Fuzzy math and with higher compression, the 392 produces 1.23 horspower per cubic inch while the 345 produces 1.07, with the added displacement the 392 should produce 50.29 horspower more than the smaller 345 engine. My goal is to find out where the extra 60hp is, i.e. better exhaust manifolds, intake and cam. Also, it was super affordable providing you do the work yourself.

@aaronferguson47

4 жыл бұрын

@@neverenuff2381 i think the 60hp also comes from the heads and valves as the 6.4 has bigger valves and a larger combustion chamber in the heads you got the cam and headers your working on the manifold i think lies in the heads they do make bigger valves for the 5.7 but still slightly smaller then the stock 6.4 valves

@ryanjpappas

4 жыл бұрын

@@neverenuff2381 I'm getting more info on here rather then scrolling through the forums and getting info from the wrong person. Everybody on here... you helped me make some decisions with my build. Add me on ig @PROJECT_RT3 I would like to see yours too

@TrippyTro

4 жыл бұрын

Thats insane number for stock cam RT I question the dyno you were on. Mine made 350/420 on a dynapack dyno. 6.4 intake, 6.4 shorty headers, high flow cats stock cam with a HPTunets Dyno tune

@Sak-zo1ui

4 жыл бұрын

I thought the numbers were low because on my 2006 5.7 (lower compression) i made 340 and 390 at the wheels with headers 3in exhaust and intake. I will be porting my intake soon and getting a ported tb.

Are you selling the sniper intake?

@neverenuff2381

2 жыл бұрын

No, it has been sold.

All the problems on this have been fixed

@neverenuff2381

3 жыл бұрын

Have they revised it? I highly doubt they corrected it.

@bronsonguzman5078

3 жыл бұрын

@@neverenuff2381 It’s been revised. There’s a few other on KZread who have it.

@malikjenkins29

Жыл бұрын

What did they do to fix the issue? And where i can find it?

You should merge this video from the original or just straight delete the 1st video of the sniper install. Shit is misleading.

I hate rtv. Never use it!!

@neverenuff2381

2 жыл бұрын

It's great for China rails on old school V-8s but these newer motors shouldn't need it!