Many must know in the early 60’s I help my dad just like many here tear apart cat dozers..sometime hydraulic-cylinders and other times the final drive on one side or the other.. I am from USA..I learn to work and I learned how things worked..Like any skill building confidence is very important for young people.. Nice work here all. It’s great to see. Hugs to the your youth helping here..

@RTFM-kg8ul

2 ай бұрын

👍

سيدي، أنا سعيد جدًا بهذا الفيديو وممتن جدًا لهذا الفيديو وأشعر أنه ساعدني في عملي ❤❤❤❤

Чтобы резьбу не срывать- зовëм детей крутить болты

Pajamas and flip flops. Standard uniform

@RADVIX313

Жыл бұрын

beer nd plad. typical hillbilly uniform😂🤣🤣🤣

It's a pity they don't have an air tool to do all those nuts, and get the job done in half the time.

@terrytenley9327

8 ай бұрын

In the 60’s we had no air tools either.. but we torn apart dozer and fixed them..Great-way to build confidence and set up for life..

They forgot to replace the small drive gear, it's also damaged.

@chad9235

Жыл бұрын

They didn’t forget, they probably just weren’t told to do it, I work with a lot of Indian and Pakistani people in Abu Dhabi and they are not prone to going the extra mile. They will usually do the bare minimum to look like they are working or completing a job or only specifically what they’re told to do.

@GrandsonofKong

10 ай бұрын

Was hoping to see that they'd pull the Swing Motor and change that gear(not sure it get replaced without removing it). But looks like it didn't....until it makes a very bad noise again.

love from Canada 🇨🇦 you guys did a great job! Can't imagine doing it without any power tools.

@pkamazingskills1867

Жыл бұрын

❤️❤️

Não trocar o pinhão que também estava danificado foi um erro...vai estragar a coroa nova.

So, this is what child labor looks like?

ما شاء الله عمال مهرة ربي يبارك بعملكم وزقكم

En la ciudad de vallarta la depesgamos con la misma maquina y 2 gatos atras en el contrapeso despues liberas el motor de transito para halarlo

صراحه فنان في شغلك

Mengganti swing GEAR kerja yang sangat berat.tapi masih d bantu dengan cren.tidak seperti yang saya buat,cuman bantuan 4 biji dongkrak.salam dari Riau Indonesia.

That looks like an expensive gear! I'm somewhat surprised that they didn't try repairing it by welding and grinding. Also was that water sitting inside the gear? Is there some missing drain or O-ring?

@blazeykk

Жыл бұрын

I think they cleaned it wit pressure water. Old ring was quite clean.

7:58 brave cameraman underneath the hanging cab section getting us our shots!

Gotta love them steel-toed flip-flops.

Vietnam 🇻🇳🇻🇳🇻🇳 xin chào các bạn

Good job 👌👌👍👍

Where is that guy with stick welder, welding these broken teeth back up??

Good job my brother

Awesome guys ❤

I love the smell of hydraulic oil in the morning😊

Masya Alloh.....Luar biasa

A little dirt and grit on precision gears never hurt anything. Yikes!

@pkamazingskills1867

Жыл бұрын

Thanks for your opinion

@videostar2528

Жыл бұрын

Must be a paper pusher

@RADVIX313

Жыл бұрын

and yet itll still work without any issues... for godsakes it's a 7 inch thick swing bearing you salty, you were told a single dust speck gets in their and theyll be "catastrophic failure" lmfao privileged shit lmao btw you guys did great, just only thing is please be very cautious when going under the machine while it's in the air, on its arm. love from Canada 🇨🇦

Very funny Iam amazed in what the kid is doing and the kid is amazed in what the camera is doing or what the camera job is !!!!!they must be proud in what they do they are very talented people nothing is impossible!!!!!!!why no change the other piece too well nobody ask me. about safety🤫

@pkamazingskills1867

Жыл бұрын

Thanks for your opinion

@robschnee8647

Жыл бұрын

Wwwwssaazeer44ru vbbbhji A 2 31 ! 4e2 31 31 31 31 43 g3 31 d3 d14 up

Máy đẹp đấy ❤

Это большой труд открутить вручную ключами и прикрутить

Minuto 17:30 ....no será mucha fuerza para esa tuerca..!!??

v The right tightening torque...? It's just an opinion!

Good 👍

I understand those guys have little to work with but why do they struggle to remove and replace the slew ring when they could've used another excavator to lift out the old one and set in the new?

@Jarobart2

Жыл бұрын

All broken😆

it is that the called gear box of excavator? or not!?

@mazzerrattiest4880

Жыл бұрын

It’s called the slew ring my friend

@RADVIX313

Жыл бұрын

swing bearing is the proper term. basically a stationary sprocket mounted to the track frame, which the swing motor sprocket rides that big sprocket and rotates the top piece aka house. ps called a swing bearing because it's essentially a bearing with ball bearings all around that gear.

Так же меняем на автокранах опорно поворотный круг.

@pkamazingskills1867

Жыл бұрын

Thanks for your opinion

Tarnol mehran plaza Ali ustad ki dukan pe 😂

Untuk jasa atau upahnya berapa pak

👍

На воду похоже. Странно что нет отверстий сливных. Сверху вода попадает, надо куда-то сливаться.

@chernoveugen

Жыл бұрын

Никакой воды не должно быть, там ведро солидола должно размазываться.... Без смазки один зуб начал крошиться и за ним дальше- больше. Причину появления воды нужно устранить....

Why are the children used for labor and not in school??? 🙁

@KH-fv3vq

Жыл бұрын

No work no eat. Simple as that

They got shit for tools, but no lack of tiny hands to turn out 189 fine thread bolts.

I wonder what torque setting they used on them bolts lol

@blazeykk

Жыл бұрын

Till two times "ouh" during tightening. They got three workers - small, medium and big and three pipes they put on wrenches, so they can get many settings 🤣🤣🤣

Culture of their work is more than terryfing! All done with flat wrenches. If they buy pneumatic one, job would be faster and could be done by three not by sevem or how many there were. Obligatory add sand to brand new element. Ant in the moments where more people needed work only one or two... I am surpised that they didn't weld it. But what with worn and broken gear? It will destroy new element really fast.

@Jarobart2

Жыл бұрын

This is Pakistan, do not expect any professional work

What bearing did you replace lmao

When SHTF these people will do ok.America on the other hand will be desparate to find someone that knows what they are doing.Key boards just don't get it done.

Ведущую не меняли?.

Torque specs, 14 year old 150 pound with a 5 foot bar😮

What could possibly go wrong?????

They like a rat repairing a pumpkin..

helllo you

@pkamazingskills1867

Жыл бұрын

Yes

What a tragedy: children working with dangerous chemicals and equipment.

@pkamazingskills1867

Жыл бұрын

🤲

@maciejpawowski9179

Жыл бұрын

it's better if they drink alcohol and take drugs and eat fast food with their parents money :)

@Roseland8

Жыл бұрын

Children made the phone you use and the clothes you wear

@__-aleks-__

Жыл бұрын

Эти дети не пропадут в жизни имея навыки в работе, они обучаются профессии.

@josesimoes4806

Жыл бұрын

@@__-aleks-__ Неправильный! Этих детей порабощают, эксплуатируют, они будут обречены на жизнь в нищете и нищете. Только такой отсталый народ, как русский, мог считать это нормальным.

Asiatic cowboys

Wrong title, should be "How do dot repair excavator". Can't see any "amazing skills" also.

Uhyf

Giao lưu kênh đi

Waste of time if you’re not going to fix the drive gear .it will soon fuck up

I guess 17:38 if I ever get to this place that will be my job!!!!!! 17:38 🔴🫢🤫

👍