"THE NOISE IS CAUSED BY UNDEREXPOSURE" or "THE NOISE IS CAUSED BY RAISING THE BRIGHTNESS IN POST" This is easy to test yourself, but I did it for you here: kzread.info/dash/bejne/qoqHwcOmlpOqgc4.html (warning: crappy screen recording). As that demonstrates, underexposed images can be cleaner than properly exposed images. Or not. There is no true correlation between exposure (meaning, the brightness of the image) and noise when shooting raw. Many of us (myself included) have previously been taught that high ISO does cause high noise, and it's much harder to unlearn a concept than it is to learn it for the first time. Here's a nerdy summary for my more technical audience: First, make sure you understand the difference between causation and correlation. In a car, your speedometer *correlates* with your speed, it does not cause it. Your accelerator *causes* your speed. High ISO *correlates* with high noise. If you're using high ISO with a properly exposed picture, your image is going to be noisy... However, lowering your ISO does not lower the noise, just like forcing down the needle on your speedometer doesn't slow your car. Low light *causes* high noise. Regardless of the ISO, regardless of the exposure, pictures with less light will have more noise than pictures with more light. Therefore, if you want to reduce noise, add light. What I hope to accomplish by demonstrating the difference between correlation and causation is to change how we think about ISO... MANY photographers in low-light situations limit themselves to a low ISO, like ISO 800, because they incorrectly believe that choosing a high ISO will increase their noise. Instead, they get an underexposed picture that has the same amount of noise (but requires additional processing). Hopefully, this lesson teaches those photographers that they only way to reduce noise is to increase the light their sensor is getting. I would also like all photographers interested in technical image quality (noise, sharpness, dynamic range) to be conscious of using giving their sensor as much light as it can handle - and using auto ISO as a measurement is a good way to do this. If you're camera isn't choosing the base ISO for the exposure, then you're not getting your camera's maximum image quality. You can't always add more light, but it's a good to quickly note, "Oh, I'm at ISO 200 - can I use a longer shutter or a wider aperture to get myself down to a proper exposure at ISO 100? Can I add light in some other way?" One stop more light improves image quality about as much as upgrading from APS-C to full-frame.

@KobieMC

4 жыл бұрын

Exactly! 🙂

@smaakjeks

4 жыл бұрын

Great addendum. I am definitely one who wondered if there was a difference in picture quality between under-exposing a picture on purpose to lower the ISO and then bringing the exposure up in post, and just using a higher ISO.

@splashstrike

4 жыл бұрын

I think you missed some subtleties: Your test relied on using a dual ISO and iso invariant camera, if you had used an iso variant camera the low iso shots would have had much more noise when boosted in post. This obviously doesn't contradict your point.

@MegaWeitzel

4 жыл бұрын

@@splashstrike In fact in that case high ISO produces less noise than low ISOs. That's why people say "choose the HIGHEST ISO you can without clipping the Highlights" to get the lowest amount of noise

@Gmagee

4 жыл бұрын

In the linked video you show an under exposed image to a "properly" exposed image. However the under exposed was at ISO 100 and the properly exposed image is at ISO 10,000. You then raise the under exposed image 3 f-stops. If you wanted to compare increasing the exposure to ISO the under exposed ISO image would be approximate ISO 800. Comparing ISO 800 to ISO 10,000 is really not a fair comparison. Yes, shot noise does have a major affect on noise in low light levels, however I don't see you discussing that here.

TONY: "People haven't hated me enough during this lockdown, what sould I do?"

@sonyssomar

4 жыл бұрын

😂

@paulscottfilms

4 жыл бұрын

He can keep on with the semi - nonsense coming out. Like biggest breakthrough in digital is that you can upload to the computer fast. Tony had run out of things to take about

@flickwtchr

4 жыл бұрын

@@paulscottfilms That post was edited?

@jurajkosco9322

4 жыл бұрын

1+1=2, 1x2=2; therefore 0+1+1=2 and is better than the other two equations.

@jbr84tx

4 жыл бұрын

Tell them you want the lockdown to continue till there’s a vaccine.

“The fourth corner of the exposure triangle.”

@Arovna

4 жыл бұрын

Maybe it's a pyramid ? Prism ?

@dubisirie2

4 жыл бұрын

@@Arovna dun dun DUNNNNNN

@Arovna

4 жыл бұрын

@@dubisirie2 just as long as it's not a mobius strip or klein bottle

@jamesn.5607

4 жыл бұрын

Tetrahedron

@BOTiTTE

4 жыл бұрын

He is too smart for us!

Tony just blew my mind! In the audio industry we often refer to this as signal to noise ratio. I now realize the sensor noise is static, and that the iso setting is just adding gain. I never realized how much photography has in common with audio engineering until now. Light is a wave just like sound. My camera is a transducer just like a microphone, so all the rules of reflection, absorption, and distance (inverse square) apply.

@ViktorEnns

2 жыл бұрын

I've transitioned from audio to photography and can confirm that many concepts are very similar if not the same. I have a lot of issues with this video though. Most of them have been addressed in the comments.

@robertox5446

Жыл бұрын

Really good comparison!

@enricomarconi8358

Жыл бұрын

yup and an amplifier won't necessarily distort a clean signal (if the latter is clean at source). If, instead, is distorted such as an electric guitar with an overdrive effect, then even at low volume the sound will be 'dirty', regardless.

@Fluffy-777

Жыл бұрын

Interesting

@EMC2recordings

Жыл бұрын

3 years after the original comment. Can confirm, as well.

ISO, beyond the basic sensitivity level of your sensor (usually 100-200) is a gain amplification applied to the signal coming from the sensor. If you use it to compensate underexposure, instead of using the real exposure parameters (duration and aperture) it will definitely amplify noise.

Jared Polin Is going to dislike this 👍

@tylermai1436

4 жыл бұрын

why?

@Sebabarrossierz

4 жыл бұрын

@@tylermai1436 they like to beat each other up 🤣

@PeanutButterAM

4 жыл бұрын

😂

@PhilJonesIII

4 жыл бұрын

With hair like that he can only have ever worked in low light.

@sulitdreamdestinations

4 жыл бұрын

Fro Doesn't Know hahaha!

The lack of a greeting made me hear the opening as “Hi, ISO.” 😂

@TonyAndChelsea

4 жыл бұрын

😂

@mokeydmeeple9880

4 жыл бұрын

Tony & Chelsea Northrup Good video though. Definitely good to get some short informative video like this.

@smartbiney801

4 жыл бұрын

@@TonyAndChelsea can you make a video explaining how you would effectively use this technique in a concert please. Thanks a lot for this information

@pdbdd

4 жыл бұрын

@@smartbiney801 also a test using a super high ISO, such as 40,000-102400

@dazzlingdeb8427

4 жыл бұрын

@@smartbiney801 I'd also like to know how to shoot a dress rehearsal of a ballet without adding noise. Sure there's lighting, but it's still fairly low light. You need a fairly fast shutter speed... the lowest I used was 1/160. My photos were good, but the noise was problematic.

A few points for people still confused about this: 1. When we say "noise" we generally mean perceptible noise. Grain we can see. All sensor readouts contain noise (the noise floor of the signal). It's only a problem when we can perceive it. At the levels we deal with in photography, it's caused by a few things, but mainly the random quantum behavior of photons, and electronic readout noise. 2. Dynamic range is the difference between the brighest part of the image and the noise floor. When a sensor is underexposed, this difference - the dynamic range - is smaller. The noise is still there, but it's too dark to see. However, a smaller dynamic range means a larger gain is required, and that gain applies to both the parts of the image we want (the signal) *and* the noise. 3. On mirrorless/DSLR cameras, ISO knobs usually apply gain before the camera's image processor gets the data. The exposure slider in post does the same thing, but after. On some cameras, ISO gain happens during the analog stage, which can reduce the effects of read noise, but most cameras *generally* have low read noise. In any case, applying gain with the ISO knob or in post makes very little difference when we're talking a few stops (ie. ISO200->ISO800 or +2eV). 4. The effect of adjusting ISO is different depending on your camera's mode. I think this is the key that has most folks confused. If you use your camera's automatic modes (program mode, aperture priority, shutter speed priority, etc) then raising ISO *will result in more perceptible noise* because your camera will underexpose the sensor. It is this underexposing which results in a lower dynamic range, lower signal:noise ratio, and more perceptible noise after gain is applied. 5. In manual mode, the only thing that affects perceptible noise is dynamic range, and this is determined by your exposure, not your ISO. The noise is always there. It's part of sensing our world. It's only a problem when we can perceive it, and that only happens when we amplify it. We only amplify it because the bright parts of the image aren't bright enough, and this only happens because we underexpose the sensor. The same is true in the audio world: in audio, we don't call it ISO, we just call it gain. When you turn the gain on a microphone up, you hear a hiss. That's noise, amplified. You can speak more quietly (akin to underexposing a camera sensor), but will acheive a higher signal:noise ratio with less hiss when you turn down the gain and speak more loudly (akin to a proper exposure). Lastly - this is not something to get worked up about. These are subtle differences for camera and math nerds. We find them interesting, but at the end of the day, it's the art that counts. If you still don't understand the point Tony's trying to make, then don't worry about it! Composition, storytelling and emotion are far more important than the details of how cameras calculate numbers from a bunch of voltages. :)

@chrisrigoni

4 жыл бұрын

Well said, Someone that is actually educated here and knows photography. Thank You 🙏✌️

@abdulhasibtamim6905

4 жыл бұрын

Wow. Great insight. But I don't quite get no 4 and 5 point. Do you say ISO in manual mode is different than any auto modes?

@GordLamb

4 жыл бұрын

​@@abdulhasibtamim6905 I think this is actually the point that causes so much contention between people! In auto exposure mode (ie. aperture priority, shutter priority, full auto, etc) the camera adjusts the exposure when you change the ISO. So if you double your ISO, the camera exposes the picture for half as long, or closes down the aperture. This "causes" noise from a user perspective. However, in manual mode, changing the ISO doesn't affect the exposure, because exposure is under full manual control. So, changing the ISO in manual mode doesn't change the level of noise (on ISO-invariant cameras, anyway), because the exposure hasn't changed. This is why there's been some frustration with the "exposure triangle" lately. ISO is not exposure anymore than the gain knob on a microphone determines how loud you're speaking or how far you are from the mic. They're connected, but not in the way a lot of people are taught from the beginning, and it gets extra confusing when we consider automatic exposure.

@abdulhasibtamim6905

4 жыл бұрын

@@GordLamb Ok. What's the source of this information?

@abdulhasibtamim6905

4 жыл бұрын

@@GordLamb Wherever you get the information I think it's not right. I just test with sony a7III, take a test shot with aperture priority and dial the same ISO, Aperture, SS in manual and got the exact same result. With the help of 'difference' layer blending mode in photoshop consolidates this too. So finally I am 100% sure that there is no difference between manual and auto exposure with regard to noise. I read many articles in Internet and watch lots of videos and come to know that there are three fundamental types of noise. (i) Analog noise: which comes from (a)heat noise, (b)shutter shock, (c)photon noise. (ii) Intermediate noise: comes from (a) read noise - basically created during analog to digital signal conversion and also depends on quality of sensor itself (b) analog amplification noise - based on ISO you selected (eg if base native ISO was selected then no amplification, if ISO is 1 stop higher than base ISO then signal will be amplified by 2 hence signal noise will also be amplified as such) (iii) Digital Noise: Comes from any amplification to the digital data (ie further exposure was added in post or in-camera JPEG conversion).

Hello, An automation engineer here with some knowledge of signal processing. I don't agree with your explanation: there is always noise, but amplifying the signal to properly expose an image increases its visibility, nothing else. The true exposure is defined by the light transmission of a lens (approximated by the diaphragm) and the exposure time (shutter speed). The camera can also have several basic sensitivity levels: simply take the signal power spectrum of an image and apply a gain to it. You can amplify the signal by using a higher ISO in your camera or in post-production, but the result is very similar with the raw format. But it's usually best to do it as close to the source as possible to avoid adding transmission noise before amplification and to work with the actual analog information and not with the digital information that has already lost some of it due to the quantization process.

@osnipso

4 жыл бұрын

Hey Tony, please look at this comment. I was about to comment something similar - you should look into signal processing, S/N ratio, signal amplification/boost/gain. You consider yourself a nerd, maybe doing real research would be nice - observing through experimemtation is fine, but it's no good at all if you have no clue on what is really happening. I have to congratulate you, not everybody can get it wrong (far from the target, btw) twice on the same subject in front of millions of people - maybe on the third? :)

@JUNO-69

4 жыл бұрын

You missed the point of the video big brain 😂

@GordLamb

4 жыл бұрын

For what it's worth, I don't think quantization significantly affects the noise floor on most cameras as long as you're working with high-bit depth raw files, at least until you get into the 10+ stop gain range. I haven't even run the numbers on my camera though. :)

@elsecomojado1

4 жыл бұрын

No no no no He knows this, he is just trying to give everyone a different point of view. I too am educated on this, so I understand and agree on your explanation. But also on the thinking outside the box view of Tony.

@samuelpua9771

4 жыл бұрын

Not trying to take it out of context, but let me try to understand your key point. "You can amplify the signal by using a higher ISO in your camera or in post-production, but the result is very similar with the raw format". So you're saying it's very similar, and results appear to be very similar (Tony's point and experiment), but generally it's recommended to amplify the signal (and noise) as close to the source (camera)? From what I saw from the video, I don't think Tony is in opposition to your point. He probably didn't intend for people to take underexposed pictures with ISO 100. Those are experiment to prove his point, and they are done in extremes (rightfully). He's saying to us, that let's not be ISO-centric, because ISO is a imaginary construct. ISO basically is a means for the camera to increase the amplification. Let's be aperture and shutter speed centric, and use them to exposure a picture properly, because that's the actual "hardware" gains you'll get. I don't see contradiction from what he's saying and what you're saying, and you guys appear to agree from my point of view actually (but of course there are others who got very aggro-ed because Tony is saying something that opposes their "mantra")

Wrong title. Should lower exposure cause more noise

@-xox-

4 жыл бұрын

But this title is more attractive. You know there will be less people watching this video if they use your 'correct' title, right?

@osirismarbles5177

4 жыл бұрын

@@-xox- Not only more attractive, but also more necessary because a lot of us (okay maybe just me) think that high ISO introduces noise. So the thinking needs addressing.

@dzsemx

4 жыл бұрын

Technically high ISO causes the noise because it turns up the gain of the sensor. Of course when turning up the gain, the dynamic range is shifted, you need less light no to overdrive the sensor. Same principle applies for audio gear. There is gain only, no shutter neither aperture. If you turn up the gain it can pick up low level sounds but the noise goes up by also. If you increase the gain but the sound is loud, it will clip, like tony's photo. Of course audio can be more complicated, there can be several stages of amplifiers.

@GordLamb

4 жыл бұрын

@@dzsemx Thing is it isn't creating noise.. it's only amplifying it. Gain doesn't affect the S:N ratio, only the amount of perceivable noise. The noise itself is created at the time the sensor is exposed and read. Same with audio; turning up the gain doesn't create the hiss, it just makes it loud enough to hear.

@patrickhudgell

4 жыл бұрын

Gordon Lamb Under-exposing an image is like having too low an audio signal. You have a fixed level of sensor noise so if you underexpose then the signal to noise ratio is low. If you then amplify the final under-exposed image (ie boost in post) then you amplify the noise too!

For all non-technical people: it's the low signal to noise ratio (SNR) that ruins your picture, not the boosted gain that is applied to make the image brighter.

@chrisrigoni

4 жыл бұрын

Well said, Someone that is actually educated here and knows photography. Thank You 🙏✌️

@robmulally

4 жыл бұрын

🙏 agree, what's wrong with teaching people what iso actually is!

@reldies5364

4 жыл бұрын

High IS or increasing the brightness in post amplifies the noice so yes ISO ruins your picture.

@sctm81

4 жыл бұрын

@@reldies5364 it's ultimately the signal to noise ratio that ruins your photo. The ratio never changes after you apply the amplification since the noise also gets amplified together with the signal. If your SNR ratio is 10dB at 64 ISO then it's still 10dB at 6400 ISO.

@rzorrilla52

4 жыл бұрын

@@sctm81 True until amplification causes clipping of the signal (AKA blown highlights)

Exposure is determined solely by shutter speed, lens aperture, and scene luminance. Insufficient exposure will make more noise visible. To get less noise, you have to raise the exposure. ISO just maps an exposure to a desired lightness.

If you a confused, the point Tony is trying to make is if you are shooting in the dark and already have aperture and shutter speed maxed out, lowering the ISO won’t do you any good in noise reduction. You need to physically get more light in the scene. Thanks for the tip Tony, I remember trying to reduce ISO thinking the darker image will have less noise when I brighten it in post before.

I have to say, that I was very skeptical of your premise, however, I just got done performing the same procedures you showed, and I was shocked to get the same results with my D800!! Thank you and your wife for all the hard work and effort you put into these videos!!

The first thing I said to myself was here we go again Tony hehe

@SPECTRA890

4 жыл бұрын

Honestly... This is exactly what I said to my self immediately I saw the title

@smartbiney801

4 жыл бұрын

Lol.... ikr

@silverrayleigh6284

4 жыл бұрын

LOL true

@jamesnelson8697

4 жыл бұрын

@SwitchRich It means less light = more noise, more light = less noise

@GordLamb

4 жыл бұрын

@SwitchRich For a given (correct) exposure, if all settings are locked and you increase the f-stop, you will lower your dynamic range / signal:noise ratio. This is not an opinion, but rather a fundamental property of math and physics. You can demonstrate it with a camera in a carefully controlled experiment, or you can run the math with a whiteboard. (apologies if you're being sarcastic, but on this topic ya never know :)

So if I uderexpose an image and drag the exposure up in post it'll be noisier than if I exposed it properly in the 1st place? What I've learned was that we need to end this lockdown so Tony can go outside and play!

@Zegmaar_Bas

4 жыл бұрын

lmao, thank you, this is indeed the reason why this video is so confusing. He tells it as if it is something new. If you're underexposing you can either turn up your iso or turn up the exposure in post, but both will result in more noise. So don't under expose if you can.... hahaha, yes that make sense, thanks! Edit: Adding to that, images shot with high iso also always will have high noise. Just as Tony says in his video, if you shoot with a too high iso on a bright sunny day, you will still get noise, because of the high iso! Overexposing and than reducing the exposure in post will still result in more noise than if you didn't shoot with the high iso. In conclusion, you can see high iso as a result of underexposing, which means noise. The real lesson is that you shouldn't see iso as a real element of the way of lightning your photos. It as fix that can boos your exposure at the cost of noise. You can also do that in post, but doing it already in the camera may let you use some noise reduction tricks and hardware your camera has build in. So to summarise, use iso as a last resort. if you see that it is high, see if you can fix your exposure in another way. That is however something I've always done, but this video helps with making you think how it works.

@GordLamb

4 жыл бұрын

Not noisier; the noise was always there... you just couldn't see it until you raised the luminance. Analogy - you're in a messy room with the lights off. Turn the lights up, and suddenly you see the mess. It was always there... it was just too dark to see.

@Zegmaar_Bas

4 жыл бұрын

@@GordLamb Yes exactly, the noise is there from the moment you're underexposing. If you than boost everything to correct the exposure, you're also boosting the noise and therefore you can see it (more clearly).

@GordLamb

4 жыл бұрын

@@Zegmaar_Bas Right, though technically the noise itself is always there, even in a correctly exposed image. It's just not perceivable, until like you say, you amplify it along with the rest of the image (which obviously you wouldn't do if it wasn't underexposed).

@jimmason8502

4 жыл бұрын

@@Zegmaar_Bas In other words always shoot with the lowest ISO you can muster. Maybe use a tripod at night instead of hand held high ISO shots. Then again, people think shooting with big apertures is a good trick at night to allow more light to enter the camera, but you have depth of field considerations as well. So shoot with the biggest aperture you can get away with and the slowest shutter you can get away with and the lowest ISO you can get away with before cranking ISO.

It’s kind of like saying, jumping off a building doesn’t kill you, it’s the sudden impact at the end that does.

@niklaskoskinen123

4 жыл бұрын

If you're going for a meaningful analogy, this is exactly the opposite: It's the low light hitting the sensor that makes people use high ISO and get noise. So the low light is the cause and the high ISO is the effect. Just like jumping off the roof causes you to hit the ground.

@stantonfuerton

4 жыл бұрын

It's even worse because he says the shutter speed and aperture cause noise, but ISO does not. It's like saying jumping off a cliff or out of a plane will kill you, but when you jump from a building, it's the sudden impact that does it

@rubinsteinway

3 жыл бұрын

Is there PROOF that jumping off a building doesn't kill? What if a person gets a heart attack BECAUSE he is fearful at the start of the fall? Just wondering. :-)

You underexposed all the low ISO shots, then tried to bring the detail back by boosting the exposure in post, that does not seem to make much sense. If you exposed both shots correctly, then the HIGH ISO shots would always have more noise.

@theboss069

4 жыл бұрын

I don't understand either why he did this. This video seems so unnecesarry.

@PraveenKumar-fs6of

4 жыл бұрын

YOU R right !!! 👍

@joshblck1

4 жыл бұрын

couldnt agree more

@davidromano2421

4 жыл бұрын

He's just making the point that the noise is coming more from shot noise than from read noise. But it was somewhat oversimplified here.

@quangpham4372

4 жыл бұрын

Okay so, let’s say you have a shot at f/8, shutter speed 1/100 and ISO 400. Now you say ISO 800 has more noise? Yeah but then you need to shoot it at shutter speed 1/200 or otherwise the exposure is not right. So the point here is that it is the fact that you choose to shoot at 1/200 that forces you to use ISO 800 which makes more noise, and if possible you always change your shutter speed and aperture to indirectly affect the amount of noise in your picture

Low light will always cause extra noise in a finished image but ISO is the only setting which increases the noise in a correctly exposed image, so it's a bit misleading to say ISO doesn't cause noise, you see more noise in the darker images because you've added additional gain into the file as well as the in camera ISO.

@TonyAndChelsea

4 жыл бұрын

It's the difference between correlation and causation. High ISO correlates with high noise, but does not cause it. This is important to understand when you want to reduce the noise; adjusting the ISO won't reduce noise but adjusting shutter speed, aperture, or light will.

@DaveMcKeegan

4 жыл бұрын

@@TonyAndChelsea but the noise comes from increasing the original signal, which is what ISO does in the same way as in post. Yes low light is the root cause but if you were to shoot correctly exposed images then the higher ISO shots would be noiser - it's no different than your 3200 film example, you have to balance the exposure with your other settings. Safest advice is leave your ISO setting until last and aim to get the exposure correct in camera

@liverpix

5 ай бұрын

​@@TonyAndChelsea By adding light or using a higher f stop/longer shutter speed you would then be using a lower ISO so it is a combination of more light and a lower ISO that reduces the noise. If I was shooting on ISO 3200 and I wanted less noise and I chose ISO 400 with a longer shutter speed then that would reduce noise surely.

This is one of Tony's "duh!" videos. Raising ISO to avoid slow shutter speeds or to avoid large apertures essentially is underexposing a photo. So it is the same as taking an underexposed photo into Lightroom and increasing the Exposure slider. It turns out that more expensive wide-aperture lenses and/or Lens stabilization (to allow for a slower shutter speed) and/or tripods all allow for an exposure with the right amount of light. Anything else is using ISO as a cheat that will bite you later down the workflow. From other videos on KZread, all sensors produce noise every time you take a picture. The more real light you are able to obtain during the exposure overrides that noise more and more (called signal to noise ratio). And yes, larger sensors do indeed have a lower native noise level than smaller sensors, all other things being equal.

@samuelpua9771

4 жыл бұрын

This is quite interesting actually. I see a few point of views: 1) Yourself, that feel that this is very intuitive and should be clear to all. Tony is overexplaining. 2) Myself, who I feel that the video is sufficiently explained and I feel like that's a good point, why didn't I think of it. I always thought that there's some magic way ISO amplify signal without increasing noise too much. Seems like I was mostly wrong. 3) Some others, who feel that claiming ISO doesn't change anything?!?! That's the mantra of photography. How dare Tony! He must be mad! And that's cool! Though I feel some comments were more rude than they should be

@danev1969

4 жыл бұрын

@@samuelpua9771 I fully agree with you Samuel. I was not trying to be flippant. I love everything Tony reports on and he often injects clarity in something I think I already know but not well enough to take advantage of in certain situations. Thanks for the comment.

@tfm2934

4 жыл бұрын

You need a combination of large aperture and higher ISO to campture dimly lit moving targets though. Cannot go by on tripods and other forms of stabilisation unless subject movement is within acceptable limits. This high ISO 'cheat' is mandatory at times. Also, the video demonstrates that on dual gain sensors, raising ISO yields better results than correcting exposure in post.

@samuelpua9771

4 жыл бұрын

​@@tfm2934 That sounds great! Sounds like you're prioritising on large aperture and fast shutter speed (to capture moving targets), thereby thinking of ISO last. Sounds exactly like what Tony recommends in the video. Obviously, the underexposed pictures are part of the experiment to see what's the effect of the 3 items, ISO (digital gains) being the least effect (usually on dual gain sensors, but otherwise minimal effect). You would still be taking properly exposed pictures, just with aperture/shutter-speed centric mindset, which is what you're doing exactly

@tfm2934

4 жыл бұрын

@@samuelpua9771 Exactly. I think the video could have been simpler on that point. But I agree with you that many comments are overly rude!

I honestly think that this lockdown is taking its toll on Tony’s sanity.

@chris-gr3cf

4 жыл бұрын

LMAO

@pegerparameta9339

2 жыл бұрын

hahahhahhahahh

@Sjorezz

Жыл бұрын

haahahha this reply deserves more attention

He's testing this on a Sony A7Riv which is ISO invariant above ISO 320 (ie. where the second amplifier kicks in). However, if you choose another camera which doesn't have ISO invariance (eg. Canon 5D Mark III) then the results should be quite different...

The process that you make in the computer when lifting the exposure is very different compared to shooting in a higher ISO (2 different stages in the image making/processing- Pre Gain VS After Gain). This whole video is extremely misleading. It only demonstrates the fact that you should get your exposure right and don't count on lifting it back in post. The claim that there is no correlation between High ISO to digital noise is ridiculous. The only thing that i can agree with is the statement at the end about using higher ISO as a last resort .

@TonyAndChelsea

4 жыл бұрын

The signal and noise are both fixed in the raw file at the time of capture. Post-processing does not add noise. "The claim that there is no correlation between High ISO to digital noise is ridiculous."

@lagazettedesfrancais8155

4 жыл бұрын

Agree

@koo3144

4 жыл бұрын

Modern Sony sensors are ISO invariant which means that shooting at for example ISO 3200 and shooting at ISO 800 but raising the exposure two stops will look exactly the same. But I agree his conclusion was a bit extreme, it doesn't work that way on older digital cameras.

@omribenbenisty

4 жыл бұрын

@@TonyAndChelsea I understand the point you are saying that the lack of light is the factor that creates noise. What i don't agree with is saying that high ISO doesn't cause noise, because it does. This due to an electronic enhancement of the signal right after it is being captured by the sensor. There is no getting around it. High ISO generates more noise if you shoot the same exposure right out of the camera. The comparison you made while trying to bring up the exposure in post is incorrect.

@spiroszaharakis2648

4 жыл бұрын

This is somehow true when you are talking about Canon's cameras that do not have "ISOless" sensors, try that on a Sony camera and you will see that there is no such thing as Pre-Grain VS After Grain. ISO is just a number that indicates the amount of signal amplification that will be implemented in the final image. Light, exposure, and sensor performance will determine the amount of noise on your image, ISO itself does not have any effect on image noise as long as you are able to give your sensor a good amount of light exposure. I am sick and tired of Video Low light "tests" that compare noise performance at different ISO speeds while keeping the exposure and the light the same. These are the dumbest tests anyone can ever make, yet everyone just keeps doing them just to prove Einstein right when he was talking about human stupidity and the Universe.

The title should be: „+5 exposure in Lightroom causes more noise than with no adjustment”. Duh...

@heliodias513

4 жыл бұрын

Kamil Pekala or Camera ISO is better than post.

@dubisirie2

4 жыл бұрын

I was thinking the same thing at first, but the more I thought about it, it just makes obvious sense. Although, he doesn't explain it very well...as per usual. While all of the example photos were noisy due to the exposure increase in LR, what he really proved is that using a higher ISO in camera provided less noise than increasing the exposure in LR (at least with the camera he used). The confusing thing is that the point he was trying to make was entirely different. He was pointing out that a lack of light is what causes noise - which is rather obvious so we tend to not ever think about it that way. And his solution was to use the auto iso as a gauge to tell if more light is needed...which anyone should be using the viewfinder info, histogram, or just basic photography knowledge to deduce anyways. He was bored and needed a video topic...

Maybe it would be more correct to say that ISO is more like a volume control. You increase the volume control to hear the music better, but all the hum, static, and other noise is increased as well. The volume control is not causing the noise, just making it more apparent.

Tony: High iso doesn't cause noise. Also Tony: Don't use high iso if you can, because your pictures will look bad.

@Joe-hm1zk

4 жыл бұрын

Why would you want to use high ISO outside with plenty of light? You'd have to crank your f-stop number up and increase your shutter speed, thus creating more noise.

@GordLamb

4 жыл бұрын

@@Joe-hm1zk Increasing your ISO actually affects how many stops of dynamic range you have above middle gray, so there are some situations where it can be beneficial. For example, if you're taking a photo outside where you care more about the clouds than the ground, increasing your ISO will capture more dynamic range in the clouds at the expense of the ground.

@osirismarbles5177

4 жыл бұрын

@@GordLamb That's interesting. I'll have to experiment. So lower ISOs increase dynamic range in darker areas?

@Falcrist

4 жыл бұрын

ISO doesn't cause noise. Fast shutter speed and high f-stop doesn't cause noise. The noise on a given sensor is always about the same. The goal is to drown the noise out by collecting more light. That means opening up the aperture and/or slowing the shutter speed in order to gather more light. The light you're gathering is the "signal", so you're increasing your signal to noise ratio. Increasing the ISO does the same thing that turning up the gain on a mic will do: increase the hiss you get from that mic. It would be better to reduce the gain and move the mic closer to the subject (if possible).

@golllluk

4 жыл бұрын

@@osirismarbles5177 I think it comes down to the fact you have 256 levels of brightness. Looking at the ground and sky scene, to have shadows be above brightness 0, and white clouds below 255, all your shadow area's might only be between 0-10, and all the clouds 245-255. But if you don't mind all your sky being over exposed and 255, the shadow area's can now be anywhere from 0-150 brightness, giving you a lot more subtle details. And vice versa with the sky.

Shoutout to everyone who actually looked at this video to learn practical technique as opposed to criticizing the controversial title

@SangheiliSpecOp

4 жыл бұрын

Agreed

@shammyh

4 жыл бұрын

Yea, but doesn't change the fact that he's wrong about ISO. Aperture and shutter speed effect the physical path of the light. They indirectly effect noise (e.g. The total intensity/count of light that reaches the sensor), but not directly. "noise" is a result of the analog-to-digital process. Light itself has no "noise". Each photon either delivers its entire energy to the sensor, or doesn't. The only uncertainty there is due to quantum mechanics, which we can ignore in this discussion. On the other hand, ISO which is the actual pull up gain of the sensor itself, directly "causes" the noise we see in the digital result from the capture of the photons.

@SangheiliSpecOp

4 жыл бұрын

@@shammyh I like this explanation

I think I get it, but let me try to restate it in simple language for us simple old people: If I am taking pix of my lovely spring flowers, and I notice that I need to crank up my ISO to get "proper" exposure, what my camera is REALLY telling me is that my fstop is not low enough, or that my shutter speed is too high. And if I reply to my camera, "But camera, I need my aperture closed down this far for proper depth of field, and I need a higher shutter speed to stop motion blur because the wind is blowing," then the camera will reply, "Then shine some light on the flower, or wait until the wind calms down, and for heaven's sake use your tripod, because there's not enough light now to keep the noise down!!" Am I close?

@TonyAndChelsea

4 жыл бұрын

Yes, James, this is an awesome explanation!

@jamesgalbreath343

4 жыл бұрын

Thanks! Now if only I knew how a camera having a "dual gain sensor" tweaked this situation...

Sometimes Tony is the perfect image of that guy who butts into a conversation you're having with "ACKSHUALLY" and goes off, and you just roll your eyes.

Wouldn't this only be true for cameras that are ISO-invariant?

@timelord2222

4 жыл бұрын

Yes it would, but someone just HAS to start brand wars every once in a while

@marcofeature

Жыл бұрын

For non ISO-invariant camera it's actually the other way around. Higher ISO means lower noise since the signal are amplified before the read-out noise been added in, so higher ISO means better signal-to-noise ratio and lower noise.

This is flat earth conspiracy theory in photography.

@benni1015

4 жыл бұрын

With the difference that its popular.

@urmumsgstring8254

4 жыл бұрын

not flat.

Mr. Northrop you have saved me, I have a Canon 90D and Sigma Art 18-35 F/1.8, my pictures always show noise even at base ISO, I was ready to quit and now I have watched and tested what you have said I have got rid of the noise problem. A massive thank you.

I think a comparison to a tachometer (measuring RPMs) is more accurate than a speedomoeter. When the RPMs get too high, you change gears, which is effectively what you're doing by adjusting your shutter speed/aperture.

@alokhaldar6855

7 ай бұрын

I very very much appreciate the effort taken by mentor Tony to see & understand this profoundly important aspect of picture - taking !!!

Anybody practicing "exposing to the right" knows that sensor saturation is paramount. If a high ISO helps/is required, OK, then use it. In my experience, using a lower ISO with proper exposure to the right results in less noise.

@felipedeornelas8054

2 жыл бұрын

@David You can always shoot with the histogram enabled and avoid clipping in real time before you shoot. I own a basic DLSR (SL3) and do that with live view. With mirrorless cameras you can do that in the viewfinder. But I agree that avoiding clipping must be No 1 priority.

KZread - "Tony, do you want to say something crazy or something that will piss off the internet?" Tony - "Yes"

@DiyEcoProjects

4 жыл бұрын

Hehehe

If you lower the image information level into the noise floor and then amplify both the image information and the noise in an attempt to recover the image, the image noise will be more apparent. The ISO setting amplifies the signal arriving on the sensor and by default the sensor’s noise, therefore the noise is a higher proportion of the signal if there is less signal. Amplifying the signal amplifies the noise. High ISO is used because there is insufficient exposure of the sensor to light reflecting from the subject, raising ISO is used to amplify what is being received. Otherwise, we just accept that we run out of road and use the widest aperture and longest time necessary to decrease the proportion of our signal that is noise. The noise is inherent to the sensor and the amount of signal amplification applied by the ISO setting, not the aperture or the shutter speed, those are independent of the sensor and its noise floor. In any shot overexposing the sensor pulls the signal further above the noise floor. By recovering the image in post, because noise floor was already very low you reduced its effects by reducing image brightness to get the appearance of a correct exposure. Going the other way round and underexposing the sensor pushed the signal into the noise floor so changing the image brightness in post to compensate reveals the noise the image is imbedded in. The processing engine of a camera already does a lot of heavy lifting to fix the balance between noise and image. Adjusting the iso partially digitally processes noise effects away after amplifying the signal. Newer cameras tend to cope with under exposure better than older ones because noise processing may be better.

Tony is actually right that high ISO isn't the demon. I found this out by mistake one time - eons ago when I accidentally kept one of the very older (Canon 60D) cameras at 1600 ISO when moving from a darker room to a brighter room. I changed the shutter speed but not the ISO and the fact that the sunlit room was awash in light, I was amazed at how clean the capture looked even at 1600 ISO - bear in mind this was back when 1600 ISO was pretty much a max limit for digital captures. It was the first time I realized that a bit of overexposure at higher ISOs was a GOOD thing - and that the real issue was combining underexposure (lack of light) with high ISO was the culprit. It's better to overexpose a bit with high ISO images and absolutely damning to not have enough light and shoot high ISO.

@jordanbabcock9349

7 ай бұрын

What's the point of the a7s series? For some reason I thought it was excellent at low light & high iso. Hm.

@pegshealth

7 ай бұрын

Yes, but underexposure is always going to be a culprit no matter what camera.@@jordanbabcock9349

0:43 uses dual gain sensor to show high ISO doesn't introduce noise in comparison to a low ISO image corrected in post with the high ISO image clearly superior in the low-mid tones. DOH! An apples to oranges comparison where the sensor is not operating with the same parameters, effectively being a completely different sensor with regards to dynamic range due to the gain applied at the sensor and not after the ADC conversion as is usually the case for these types of comparisons (digital gain). Given that there are many strategies with regards to gain, it cannot be claimed as a universal that ISO settings are effectively noise neutral to the output when your first example clearly demonstrates that this is not the case.

@davetinoco

4 жыл бұрын

...and is fixed by adding more light...i am sure he didnt keep the ISO the same after adding more light LOL

If I understand correctly, the takeaways are: 1. Underexposing causes noise; a properly exposed image will always have less noise (regardless of ISO) than an underexposed image pushed in post, even for ISO-less sensors 2. Among properly exposed images, the one with the highest ISO setting will be the noisiest

@TonyAndChelsea

4 жыл бұрын

1. Underexposing doesn't cause noise if you keep the aperture, light and shutter speed the same... the noise is pretty much the same whether you properly expose it or adjust it in post. 2. Yes, high ISO correlates with noise, but does not cause noise. That's why I suggest using auto ISO as a speedometer, so you'll have some sense for how much noise you'll get in the final image. If you want to reduce the noise, you need to look at light, shutter speed, or aperture, because those have a causal relationship with noise. ISO does not have a causal relationship with noise.

@epiphoney

4 жыл бұрын

@@TonyAndChelsea Correlation not causation.

@shammyh

4 жыл бұрын

@@TonyAndChelsea You still have it backward. Shutter speed/aperture doesn't cause noise. Those are the physical paths of the light. The ISO itself is the ONLY part that actually introduces noise. The sensor doesn't care about the aperture/shutter speed, those are separate physical phenomena, the sensor itself, translating the energy of the photons into digital bits, is where noise is introduced. "noise" is just another way of saying "uncertainty of measurement". The aperture and shutter do not directly effect the measuring process. The only setting that actually changes that process, is the ISO setting. The concept of using auto-ISO as a speed limit is quite sound. And what many of us already do. That makes perfect sense and is a useful message to share. But please don't double down on the incorrect parts of your video in order to justify the useful/correct parts. That's just ego.

@yourtallness

4 жыл бұрын

OK, that's why the first image that was underexposed via ISO was the cleanest of all boosted images. It wasn't exactly as good as the high ISO image due to the dual gain (does pushing 6 stops in post border on the limits of ISO invariance though or is it unrelated?). Taking it even further, for ISO-less sensors at least, one could say there is no longer an exposure triangle, as those cameras effectively have a single ISO and exposure is only determined by aperture, shutter speed and available light.

@Streamtronics

4 жыл бұрын

@@TonyAndChelsea Are you sure the noise is about the same when adjusting in post vs. using higher ISO? I was under the impression a lot of cameras actually apply analog gain depending on ISO. At leas with my old 50D it makes a huge difference, noise is brutal if I adjust it in post instead of using a higher ISO in-camera.

I proved this to myself last night. We frequently have whitetail deer in our back yard. In the last month I upgraded my Canon Rebel T6 to a 90D, and upgraded my glass from the 75-300mm kit lens to a Sigma 150-600 Contemporary. I live on the west side of a hill, so light fades in my back yard well before sunset. I first tried photographing the deer at 600mm F6.3 (wide-open for this lens), 1/1000, and auto ISO (25,600). I got nice sharp images, but there was a lot of noise. Taking the advice of this video, and another of Tony's videos (on finding out how low you can get your shutter speed hand-held), I moved the shutter speed down to 1/250. The image was underexposed, but when I looked closely there was little to no noise in the image. Thanks, Tony!

@liverpix

5 ай бұрын

If you moved the shutter speed to 1/250 sec you would have increased the exposure/light so why would the image be underexposed ?

@TheKingsOutlaw

5 ай бұрын

@@liverpix It was a long time ago. I may have messed with the ISO as well. Sorry, I just don’t remember the situation.

Great explanation Tony. I have always been an available light shooter and tended to towards wide apertures on expensive fast primes. I recently started playing around with some slower but modern Leica/Voigtlander/Zeiss M lenses adapted to my Fujifilm APS-C camera. I realized what I really enjoyed was clean images with sharpness and tone more than bokeh; shooting a scene at f5.6 or tighter gave me what I wanted more than at f1.4. The consequence was I just started setting my ISO to the most tolerable setting for that time of day and shooting with a mini tripod. Instead of wasting money on glass I started to use the creative restrictions of shooting with a $30 mini-tripod as my guide to setting up shots. I was always afraid to "waste" the expensive glass on more moderate f-stops but I knew I didn't want blurry photos; by admitting what I wanted I sold off some expensive glass and just focused on what was sharp as well as a few cool stabilization techniques. The noise (or signal to noise ratio) is always about available light and separating it from ISO is important in thinking about exposure; ISO is gain to boost signal (and noise) and the more likely you need to add gain the more likely you need more light in your shot for your preference in noise level. Like you, I always viewed the % of my maximum allowable ISO for the setting as a measure of my success in curating the shot. Excuse the long comment, hopefully someone finds that valuable.

@robinlikes2learn

2 жыл бұрын

What you're saying is that high ISO boosts noise (and signal) which Tony says doesn't occur. He specifically says in his opening statement, 'High ISO does not cause high noise' - so which is it to be believed, you or Tony? This theory of Tony's is fine for the studio, but has no basis in real life outdoor photography where the light conditions can only be altered by either a) moving the subject into a better lit spot, but if that isn't possible then b) by providing extra light in the way of flash or reflectors. Yeh, try that on a race track! Tony should have been more specific in what he was outlining because in circumstances that require fast shutter speeds and the widest aperture your lens is capable of in lighting that necessitates a higher ISO, then you will get more noise - fact! Lowering the shutter speed will of course lower the ISO for the same lighting conditions and subsequently lower the noise, but will increase blur (and I know which I would prefer) Alternatively, if the aperture is reduced in order to preserve the shutter speed and the ISO left as is (lower than required for the A/L, ) underexposure will occur and on none ISO variant cameras (which I imagine the majority of us have) then noise will be increased in post to the same extent as it would have been had the ISO been increased with the same aperture at the taking stage. So where's the advantage in underexposing and increasing the brightness in post? None from what I can see.

@denvan3143

Жыл бұрын

@@robinlikes2learn what is 100×0? Zero. What is 100×5? 500. ISO doesn’t multiply noise that isn’t there; it doesn’t cause noise, it amplifies it. If you increase light and thus increase signal to noise sufficiently there is negligible noise to be amplified.

Coming up next: Focal length has nothing to do with the FOV.

@pedrogoncalves2074

4 жыл бұрын

Well its funny because to some extent it doesnt ! xD

Raising exposure in post is simulating high sensor gain. This is a misleading video

@SupremePhotoVideo

4 жыл бұрын

I concur

@GordLamb

4 жыл бұрын

That's his point. :) Neither gain applied on the camera using the ISO knob, nor gain applied in post create noise; they merely amplify the noise that existed at the time of capture. Dynamic range is determined by exposure levels, not gain, and captured dynamic range dictates the required final amplification. If you want to reduce noise, you need to capture a greater dynamic range, and you do that by correctly exposing the sensor, not applying gain with the ISO knob.

@ralphgeronilla

4 жыл бұрын

Gordon Lamb oh yeah, push the gain on your camera and correct exposure by using ND filters, aperture and shutter speed and tell me how the image looks.

@GordLamb

4 жыл бұрын

@@ralphgeronilla so the whole point here is that gain/ISO has nothing to do with exposure. It's not part of exposure. ND filters, scene luminance, shutter speed, and aperture are really the only variables. So long as those variables are configured to maximize dynamic range of the sensor, you'll end up with the best possible result.

@thecommenter578

4 жыл бұрын

Because it is the same. Apply gain on post or do it in camera, gain is still gain

I have an older Canon 50D. At ISO 400 is is noiceless with a well exposed image. At ISO 1600 it's very noisy with the same well exposed image. Same lens, same camera, same aperture (f2.8) and the shutterspeed is two stops higher. I've always thought of ISO in digital cameras along the lines as radio reception. At the base ISO that the camera has - and it has only one - the noise is excellent. A radio picks up sound from a local station and it sounds good. If we want to listen to a radio station whose signal is weak because it's a distance away, we turn up the sound and hear the broadcast more clearly but we also hear popping and buzzing as the background signal noise. When we raise the ISO in the camera we are telling the camera that we will accept the weaker signal (less light) and through camera noise reduction and RAW noise reduction algorithms we reduce the noise to make it acceptable.

So I came a little late to this, but it's as simple as to think that raising ISO is just like raising your exposure bar in lightroom. So it creates noise by retrieving the details in the shadows and mid tones. So technically it is not the ISO what creates noise, actually noise isnt created, its always there, it's just a matter of how visible it will be. And it will be more visible when there is less light, when there is more light, the light overlaps the noise (SNR).

2:28 "But officer, I wasn't speeding, the accelerator was speeding"

When i shoot the milky way with 1600 iso, the image has more noise then when i shoot outdoor with sunlight using iso2000. The missing of light cause the noise

@Shmyrk

4 жыл бұрын

Absence of light Good point!

@zaidmuscle80

4 жыл бұрын

You explained it better than Tony

@HappyHubris

4 жыл бұрын

I don't think that's a useful comparison. You would need to compare the sun-lit image at ISO 100 with an equivalent scene shot at ISO 2000 and 20x the shutter speed.

@mohsenalfaraj207

4 жыл бұрын

Brent Schumer my comparison was not accurate by any means, only something I noticed while shooting

@slosmoke1

4 жыл бұрын

In a Milky Way photo, you want the sky to look dark, thus you are underexposing it and you'll have noise.

Studying astronomy has made understanding photography so much easier. We work with CCDs and I'm responsible for checking the gain of the detector, which we use a monitoring script for. The gain is basically how sensitive the detector is to photons, and how much it can convert photons into electrons. The unit for gain (in astronomy) is electrons-per-DN where DN is digital number or the photon number. So if your gain is 2 e-/DN then for every photon that hits your sensor/detector/CCD you get 2 electrons of measurement. So with ISO if you crank it up from 400 to 800, you're effectively going from let's say a gain of 1 e-/DN to 2 e-/DN. Same for 800 to 1600 and so on. The amount of noise in a single pixel follows the poisson noise (shot noise) and is equal to square root of N, where N is the number of photons hit. If you don't have enough photons in an image (aka its severely underexposed), your shot noise relative to your photon count is going to be sizeable. If you have plenty of photons in an image (appropriately exposed) your shot noise is going to be minimized. So if you had 1 photon hit a pixel, your shot noise is 1. Whereas if you had 100 photons hit a pixel, your shot noise is 10. 10/100 is less than 1/1. So basically if you appropriately expose your image given the gain of your detector (ISO), you can minimize your shot noise. This is basically what Tony demonstrated. We have calculators set up to optimize the exposure for scientists who use our facilities, we call them exposure time calculators or ETCs. It's like the instant readout you get on your camera for your shot, but in this case scientists put in the object they want to look at in space plus what filter they want to observe in (infrared, ultraviolet, blue/green etc.) and it does a series of calculations to tell you what the exposure time should be, what the detector should be pre-flashed with light to, and what the final estimated brightness will be.

You are wrong on so many fronts! ISO is a gain control, it takes what you capture and amplifies it. If you have noise mixed with the light, SNR, then you will amplify both, if there is plenty of Signal (light), but very little noise in the capture, let's say, 90% signal and 10% noise, then any gain you apply, will increase both, but 2X 90% is far better than 2X 10%. In low light situations where the SNR is more in favour of noise, 60/40 split, using the gain will result in 2X 60% noise as opposed to 2X 40% signal. You don't need to be a mathematician to realise the bigger percentage will always win out. Electronic components also create their own noise, which adds to the total noise when engaging high ISO settings. The worst mistake you made, was using post production to try to compensate for shutter and aperture settings, as post production can add quite a lot, if not excessive noise to the already bad image. The answer is quite simple, you get the best SNR, ( light), from the composition you can, before you apply the ISO gain. In other words, in low light situations, drop your shutter speed, or pick a bigger aperture before you resort to picking a higher ISO. If you don't, and your capture has a high percentage noise level, upping your ISO will only boost the noise level and make the image worse. The more light that hits your sensor, the less noise there will be!

I've never seen Tony respond to so many comments :) He's right. Test this with your own gear (without blowing out the highlights) before disputing it. I was surprised with my testing!

@shammyh

4 жыл бұрын

Just did. And this he isn't correct. He also knows it, which is doubly annyoing. The concept of "ISO as a speed limit" is pretty clever and correct. However, do it yourself: compare at the same aperture, ISO 100 @ 1/200 to ISO 400 @ 1/800. Same exposure. Tell me which has more noise. 🤔

@fixitrod4969

4 жыл бұрын

@@shammyh You changed your shutter speed to test. You didn't prove anything. You have to match exposure in post to test this theory. Try keeping lighting, apeture, and shutter the same, take a pic at iso 100 and one at iso 400. Adjust the exposure in post 2/3 stop or so to make them the same exposure. Then look at the noise.

Since high ISO do not cause noise Tony , please show us a well-exposed image at very high ISO that do not contain noise. (It's sad to write and say things that are NOT true! Very sad...)

in short: noise is a function of total light gathered which is affected by aperture (flow) and shutter (time). ISO is a gain applied to the signal post-capture.

I actually just figured this out yesterday doing macro photography. It was a very cloudy and overcast day. I went outside and I was using a flash with a paper plate setup on my Canon 100mm f2.8 lens.. I was shooting at 1/200s of a second f16 with ISO 6400. Because I was using the flash to introduce extra light. When I checked my photos in Lightroom there was no extra noise. Originally I was upset I had to crank up my ISO to 6400 because I knew that the amount of noise being introduced with the aggravating. Or at least I thought so. But the end result came out phenomenal. After doing a Google search of this I could not find a definitive answer until your video Tony. Thank you again for the wonderful upload and I hope you and Chelsea have a blessed and wonderful week.

Tony, You are Saying The Same Thing in a different WAY, Right ? i.e. Less Light Makes Noise !!!

@TonyAndChelsea

4 жыл бұрын

Yeah, less light = more noise.

@andyrao7700

4 жыл бұрын

Less light is more noise is known but the misconception that one shouldn't raise the ISO in challenging situations is wrong... so the titles correct !

@eduardobianchi4564

4 жыл бұрын

Less light doesn't cause noise, it causes a underexposed image or a low key image... however noise is produced when you force your sensor by increasing iso to be more receptive of the little light is there. If you had a 4 stops underexposed image and gain light by each of the settings the result would be very different. Shutter speed would cause movement, aperture would cause shallow depth of field and ISO WOULD CAUSE NOISE.

@iceinvein

4 жыл бұрын

@SwitchRich he was clearing up your last sentence. But i guess you totally missed it.

@Justas49

4 жыл бұрын

@@eduardobianchi4564 No, watch another video from Tony. About ISO. If you correct underexposed RAW by 4 stops in post it's the same as raising ISO in camera before taking picture. Do You think this channel has millions of subscribers and don't know how exposure work?

It all comes down to the signal to noise ratio. If you cut down the light to the sensor, the ratio between your image and the noise floor decreases. You recover your image either through amplifying the signal+noise either in the camera (higher ISO) or in post processing. Same difference. So noise is caused by lowering the level of the signal (light) to the sensor. EE's point of view.

The noise is always there. The same noise is in every photo here. When more light hits the sensor it overrides the noise. So Tony's right, more light (signal-to-noise ratio) less noise seen in image. Look through your viewfinder with the lens cap on. There's your noise.

ISO is a signal amplifier. The signal in photography is light. Less signal = more noise. If you boost the exposure of a scene, either when taking the photo or during post-production, there will be more visible noise because of the lack of light. The information lacking in the picture because of not enough light is filled by random pixels of different colors by the digital cameras.

*sits and waits patiently for Ken Wheelers response 😳

people who haven't watched the previous videos Tony made on ISO invariance and how ISO is fake are going to be so confused lol

@TrevorMatthews

4 жыл бұрын

Yup, my first one. Is this some inside joke?

@themustang181

4 жыл бұрын

Yeah this seems a little misconstrued. Using iso to boost your exposure in low light does increase noise esp in shadows... I don’t understand the point he’s trying to make. Like yeah it’s technically the lack of light that makes it noisy, but cleaner gain sensors don’t look as noisy in the shadows even when both are at native.

thanks, this is really thought provoking. Just want to add something here, noisy image is caused by not high enough Signal-to-noise ratio, meaning the sensor cannot collect enough "good" light signal to combat the noise naturally occurring in the circuit of the sensor. So high ISO is really not to be blamed, it's by increasing the ISO, you are allowed to use a faster shutter, which in turns reduces the amount of "good" light that hit the sensor.

Simple setup: take images with the lens cap on. Change ISO. Change Shutter speed. Change Aperture. Do the same for each setting of ISO. Look in Lightroom. Do not adjust exposure. Look at the difference. Then increase the exposure for EVERY image to the SAME increase of exposure (+5). Look at the difference. On my Canon 5D MK IV, at ISO 100, the images are black and stay black, regardless of shutter speed or aperture. At ISO 32000, the noise from the sensor can be seen in the image before exposure adjustment and is accentuated drastically when exposure is increased. This means there is, at least for Canon, a direct correlation to increased noise at higher ISO settings. (ISO100,1/60,F1.8;ISO16000,1/60,F1.8;ISO32000,1/60,F:1.8;ISO100,30",F16;etc.etc.etc.) The point about low light is valid, but to say that ISO doesn't produce noise, at least for Canon, is pretty easy to show is not correct by doing the lens cap test.

High ISO doesn't cause the noise to exist, but it does amplify it.

@soumiksen

3 жыл бұрын

YES.... YES.... and YES.... Thats EXACTLY what happens. ISO is sensitivity of the image sensor to light, i.e sensitivity is increased / amplified electronically. If there is less or no light, then the output of increased sensitivity of the image processor would be noise because it has nothing to amplify. Sadly. this video would only make sense to people who are new to photography.

is this a troll? I don't get it.

@Falcrist

4 жыл бұрын

The noise on your camera's sensor is actually pretty static. No matter what your settings are, the noise stays about the same. ISO increases the brightness in the same way that turning up the gain on a mic increases the volume. Any hiss on the mic is also amplified when you do that... just like the noise on your sensor will be amplified when you do that. Ditto with increasing the brightness in post. The goal here is to increase the signal to noise ratio. In this case, the "signal" is the light you're gathering. Thus, if you want to "reduce noise", you simply gather more light by decreasing shutter speed or f-stop. The extra light helps drown out the noise.

@aizel330stream

4 жыл бұрын

@@Falcrist sure but on the real world you use the iso to compensate for the lack of light... so what the hell are we talking about? you should always have a correct exposure... if you recover the dark part of the image on post it's obvious that you are going to have tons of noise in the picture...

@Falcrist

4 жыл бұрын

@@aizel330stream Honestly, I'm not sure what the point of the video is. High ISO does indirectly "cause more noise" in the final image by making you increase f-stop and shutter speed to compensate. That reduces the amount of light gathered and thus the SNR of the image is lower. But if he wants to be pedantic, he's doing it wrong. Even the high shutter speed and f-stop doesn't cause the noise. The noise was already there, you're just not gathering enough light to drown it out.

@aizel330stream

4 жыл бұрын

@@Falcrist exactly, that's why I don't get if he's actually trolling or what... ahahahah

@Falcrist

4 жыл бұрын

@@aizel330stream He's not trolling lol There's *some* value to understanding what I explained... Not much, but some. I just think this video is a mediocre explanation.

Your sensors sensitivity to light is fixed. It cannot be changed in any way. How much light reaches your sensor is determined (camera wise) by aperture and shutter speed. If little light reaches your sensor, the signal to noise ratio goes up as the sensor starts to mis-read the vague light. ISO is a factor the processor/software of your camera applies to the readings of the sensor. High ISO when used to compensate for lack of light will hence amplify the noise that is already there. So the little word "cause" is the debate here. In my mind, high ISO does not cause noise as such but will amplify it if present. So if you shoot with auto ISO on and the ISO value goes ballistic then you know light is missing. I think that is Tony's point. And a good one. So see the ISO as the canary in a coal mine. And don't worry about all the tech stuff.

Increasing ISO does induce noise if used to correct exposure...If you increase ISO (or raise brightness in post) to correct the exposure 'when' there is insufficient light on the sensor you WILL increase the noise. In other words, if you use ISO (gain) to correct for underexposed, you will introduce noise in order to gain the correct exposure.

I normally think Tony gets stuff right. But Flawed testing here. The image noise primarily exists in the shadows. So if you underexpose shots. You have more noise. Regardless of how you end up being underexposed. Shutter, aperture, light or ISO. If you have the same decent exposure, but THEN increase ISO. You will get more noise. That doesn’t happen for shutter or light or aperture. If you have the same decent exposure but vary shutter, light and aperture for each. And keep ISO the same, Then you will have consistent noise level.

@tfm2934

4 жыл бұрын

He clearly demonstrated the opposite in the video, in a way that you can easily reproduce at home. Keeping ISO the same but varying SS, aperture and light change the noise level, as they change the amount of light.

Shoot a photo at iso 52000! That is high ISO!

A lot of people are missing the point that high iso isnt inherently noisy. Which i always thought it was. Great vid for a beginner like me.

good point, we can understand the video like this: increasing ISO = increasing exposure in post editing, they're same technical light boosting which causes more noise, but the ISO in the camera might work a little better in some way, that's why (ISO100 + increasing exposure in post editing) looks worse than High ISO

The “noise” Tony is referring to is his own voice. The solution is to turn off this KZread video and watch someone who knows what they’re talking about. Hope that helps!!

What a great concept, speedometer.

Absolutely right on. This is a basic concept that everyone should understand as it will help them make the most of their equipment. The root cause of noise is the absence of light. However you want to slice it-- fewer photons hitting the light wells on the sensor die will result in the signal being harder to distinguish from the noise floor of the sensor. Heat, 'dark current', read noise, random cosmic ray strike-- whatever will cause that light well to generate an electron that isn't a photon coming through your lens contributes to the sensor's noise floor. Until you expose long enough to collect enough signal to really overcome that-- you get noise. On any digital camera, 'ISO' is just sensor gain-- it is just a multiplier applied to the sensor readout. It can't make that silicon chip more sensitive to light and it can't create signal that isn't there.

It's hilarious how many people either 1) totally miss the point, or 2) are so stuck in the incorrect idea that "high iso causes noise" that they can't even begin to comprehend why they're wrong. Kudos, Tony. Breaking down photography myths is no easy job.

I've watched quite a number of your videos and topics. I want to say thank you for basically pioneering this new way of understanding and applying digital ISO. This is probably one of the top 3 things for all photographers (ok, maybe it's just me) to understand. I got a glimpse of this on my own from a portrait I took years ago around high noon. It's one of my favs, but I think I had aperture priority on and it pushed the shutter speed to something like 1/4000 (max on the Lumix GX1) and ISO to 3200. I thought I ruined the shot because of the high ISO, but it turned out to be a perfectly clean image. That made me curious over the years and I concluded that if I have enough light, ISO shouldn't matter so much. BUT, you've really pioneered the theory/application and I thank you for this. At the end of the day photography is still light (photo) drawing (graphy) with an emphasis on the photons! Brilliant.

@TonyAndChelsea

4 жыл бұрын

Thank you Omar!

@osirismarbles5177

4 жыл бұрын

I did my own testing with a Lumix GH3 and GX85 and found some REALLY interesting results. Keeping A/S constant, MORE ISO results in LOWER (tho similar) noise than LESS ISO with EV compensation in post, **BUT** LESS ISO results in MORE DR. So, as always, this area of photography is about compromise (what's more important to you for your scene? improving DR or limiting noise?). Of course, allowing more light in by adjusting A/S also reduces noise. When constrained, we may decide to shoot somewhere between metered ISO and base ISO to get better DR and less noise. This whole topic just changed my photography. I feel way more empowered now and it's not just theory.

Give me back "Kodachrome" ASA 64 😎

@ashley1scott

4 жыл бұрын

Ilford make PanF which is 50 ASA

@1j007zm

4 жыл бұрын

I miss all the chrome films so much, especially Kodachrome!

@Lesterandsons

4 жыл бұрын

I still project my 25, even underexposed no noise. I miss you.

Signal to noise ration is the ONLY factor that affects the noise you see. A photosite that is 50% full will have a worse signal to noise ratio that that same photosite at 90% full. Simply put, the more PHOTONS you pour into a photosite, the BETTER it's signal to noise ratio gets. ISO/GAIN DOES NOT CHANGE THE CONDITION OF THE PHOTOSITE. A photosite that is 50% full 100 ISO will STILL be 50% full at 800 ISO and still 50% full at 3200 ISO,...and yes,..that same photosite is STILL 50% full at 1 billion, trillion ISO. Dual ISO/gain systems will PRE-AMP the A/D converters for that 50% full photosite at different gain amounts but again,...the ONLY thing that changes the actual 50% full condition of the photosite is to FILL it with more photons. You can only do that with a slower shutter speed or wide aperture. Shutter+aperture = LIGHT. ISO/gain = amplification of a 50% full photosite!

Tony, As pro's, we are taught that "shadows create detail". That's fine in theory, but not always applicable in real world situations. For example, in my real estate photography business, I shoot a majority hand-held at a higher ISO's than I would like - this is dictated by pricing, and number of homes I shoot daily. I have found with my EOS R and 16-35L f4 IS, a comfortable ISO to be around 800. This means I am shooting a standard room 1/60 @ f8 with flash at 1/4 power (angled 45 degrees back over my head) . I am able to add enough fill to not create bounce shadows, while retaining detail shadows and not blowing out highlights (windows).

Hi Tony, I got some confusion here though. R u increasing ur ISO in post at 01:29 which makes it noisier than the right-hand side photo? so the comparison is not fair since is it ISO 12800 vs ISO 6400

Next up: “Light has nothing to do with photography”

@RomanCatholicTruth

4 жыл бұрын

The whole point of this episode is that light affects image quality.

@KevyB.

3 жыл бұрын

🙄🤦🏽‍♂️

I think the takeaway here should have been a properly exposed image reduces noise. In a dark environment, If you have the ability to add more light (ie. a constant light source or flash) then you will reduce noise, if you have the ability to lower your shutter by using a tripod thereby exposing the sensor to more light you will reduce noise, if you have a faster prime lens and you shoot wide open thus exposing the sensor to more light then you will reduce noise. I think this has to do with the signal to noise ratio no? Simply bumping the ISO will not in and of itself increase the amount of light available - thus more noise introduction. It's a fascinating topic though. Thanks for taking this one on Tony. Always one to face the controversy head-on - lol ;)

Even with all of those other options, sometimes you have no choice. But agreed if you can bring more light/exposure into the shot the better. After all, PHOTOgraphy is all about LIGHT. We are light painters!

But dont you bring up the "ISO" in post? Thats why there is always more noise....

@ChristopherGoetting

4 жыл бұрын

Yeah, digital ISO is really "gain" which is what the exposure slider does. Typically, camera processors are more efficient than what your computer can do in post. The real takeaway from this is to shoot your image perfectly exposed or as bright as you can without clipping highlights (ETTR) then adjust it down in post. It is always better to shoot with a higher ISO to get the exposure where it needs to be than it is to underexpose and lift in post.

@felixruppert4498

4 жыл бұрын

Christopher Goetting They aren‘t more efficient actually, it‘s only that the ISO control boosts the actual voltages before the Analog/Digital Conversion. As the picture on the Computer is digital, it has to boost the digital signal, which was already processed, even in RAW.

@ChristopherGoetting

4 жыл бұрын

@@felixruppert4498 yeah I was simplifying

@TonyAndChelsea

4 жыл бұрын

No, the noise is present in the file when it's captured. Post processing doesn't introduce noise.

@youknowwho9247

4 жыл бұрын

@@TonyAndChelsea I feel like this way of framing the problem is overly complicated. When one brightens an image in post, that's really just an amplification of signal and noise, increasing their respective visibility to the human eye. Technically the signal to noise ratio doesn't change, so it's correct to say that the noise was always there. But brightening in post processing (or raising ISO in camera) is what makes the noise visible. Therefore, I'd argue, a more intuitive way to frame this is to say that increasing the ISO or brightening in post increases the *visible* noise of an image. [To clarify: This is about this particular comment thread. The overall point of the video seems valuable nonetheless.]

Thanks Tony, the learning curve was steep. Been shooting since the days of film, so my thinking of ISO (or ASA as we use to call it) is a carry over just as you said. I use to love shooting Kodachrome 25 back in day, the sharpest 35mmm sold at the time. Your next video could show how to reduce noise in post, LR can be useful for this as well.

He does make some sense, I don't think his statements can be entirely dismissed. Think of bird or sports photography in daylight. We shoot with high ISO so we can get the shutter speed as low as possible. An ISO of 6400 in sunlight will definitely not show as much noise as 6400 in low light. So it is certainly acting as a speedometer in this case, directly correlating to faster shutter speed.

Totally agreed. The total amount of light that shine on the sensor do, not iso! High ISO actually reduces noise in most cameras, especially in canon!

you've got it backwards... basically, digitally brightening the image causes noise, like using high ISO or brightening in PS. mechanically or physically brightening your image doesn't cause noise, like adding a light source, using larger aperture or slower shutter speed. too slow of shutter speed does cause noise to rise up again because the process becomes digital. the CMOS is basically accumulating light and noise at the same time so the longer the exposure, the more noise it accumulates.

@TonyAndChelsea

4 жыл бұрын

The noise is present in the raw file at the time of capture. Processing does not add noise.

@Ballacha

4 жыл бұрын

@@TonyAndChelsea you are right. noise is present in every photo. digital processes amplify noise rather than creating them. the more accurate choice of word in my comment should be "digitally brightening the image causes noise to be visible". but still, the general rule of thumb for minimising noise is minimising degital process, and use physical processes wherever possible.

Spot on. Low iso's don't prevent noise in my milky way shots if I fail to gather enough light. I often need 3 or 4 minute long exposures of my foreground to prevent high noise when i bring the shadows up. Gathering light is like catching rain in a bucket; if you don't have enough you're screwed regardless of how good your sensor is.

I officially believe Tony has become a Troll. I'll be honest this shit is hilarious 😂

While under exposing and correcting in post certainly reveals more noise, it’s also true that the sensor’s signal to noise ratio is more favorable at lower ISO. I think he has a point about less light causing more noise, but I don’t think it’s true to say that noise is not at all related to ISO.

Don't ruin your entire photography experience by watching this video...this just gonna make you bad photographer...so stay with the basics,just ignore what he explained in this video.

@jaypob

4 жыл бұрын

That be unfortunate to not want to learn. Sounds like a good way to stay a bad photographer.

I found this out myself by trying to limit my camera to low iso which meant I was underexposing and got noisy images so now I let the camera choose iso and keep checking the histogram for correct exposure and yes using the auto iso as a “speedometer” is a handy tip .

@TheFykle

4 жыл бұрын

Noel Chignell but then lose detail , even more so when crops

@scenesnatcher

4 жыл бұрын

I found that out too. I posted it above. If I let the camera find the correct ISO, then expose to the right based on my histogram, not only did the noise subside, but the color was richer. The noise was still prevelent, but way more manageable then exposing correctly.

Easier said than done when shooting wildlife with telephoto lenses and the need to use fast shutter speeds to prevent motion blur! The light outdoors at any given place on any given day is fixed. The beauty of larger sensors is that you can dial up the ISO more and still see less noise. ISO 6400 on my Panasonic G85 is nearly unusable. ISO 6400 on a Sony a7s II is VERY usable. And that can be crucial in a situation where you don't have much control over the light or as much flexibility to reduce shutter speeds. I have found sports and wildlife photography can really push a camera to its limits like no other type of photography.

How does this help at all? If we're in a situation where light just isn't available, even at the slowest shutter and widest aperture, what can we do? Increase ISO. And what does that do? Increase noise. That's just how it works, but Tony here just made a whole video as if we can make light appear out of nowhere to be at out disposal... You could make the exact same video, but from the perspective of the Shutter, and then the Aperture, and then the editing software, always blaming the others for causing noise. That's not how things work though... If you raise the ISO, your amount of noise WILL increase! Simple!

So it's similar to gain, and noise caused by electronic (digital) amplification of sensor when there's not enough light (Sorry but speedometer comparison was a bit confusing to me)

@yfphotography4119

4 жыл бұрын

Yes. Exactly

Ken is gonna love this

It’s not film…it’s an electronic camera with adjustable gain. This is effectively an amplification circuit which is amplifying the signal coming off the sensor. What you’re talking about is signal to noise ratio. Obviously, if you have plenty of signal (light) you have less noise… less signal, more noise. It’s simple… and nothing like a speedometer. Also proving your point with a dual base ISO camera just confuses the argument totally.

Great video. The reason high ISO (or ASA for us old people) film lead to grainy images is because the silver halide grains in the film were physically larger than the grains in lower ISO film. I love nerding out on things like that.

As far as I can see all you showed is that if you underexpose an image and then try and retrieve it in post then you get more noise than if you expose it correctly in the first place!

@TonyAndChelsea

4 жыл бұрын

All the signal and noise are present in the raw file when you capture it. Post processing never adds noise.

@patrickhudgell

4 жыл бұрын

@@TonyAndChelsea What you are doing by under-exposing is reducing the signal but keeping the noise constant. So the signal to noise ratio is lower when under-exposed. A "correct" exposure is the optimum signal to noise ratio. When you have an underexposed image and try to boost the signal in post you also boost the noise so surely that is why the image looks more noisy.

i hope that Tony and Jared can do a photo shootout collab someday. It'd be really interesting

I just took 2 (identical) shots of a house ... both in aperture priority at f/13.... both with correct exposure... One was shot at iso 200 and one shot at iso 3200.... not surprisingly- one yielded 1/200th sec shutter speed- the other 1/3200th... No prizes for guessing which image yielded the most noise... I'll leave you to decide if it was the high iso or the 1/3200th sec shutter speed that was the cause...