Peri: 'You wanted a muscle bound hunk?" Ladyfractic: "Yeah, but you'll do" 😁😁

"My computer printed a computer" - That's how it starts. Before long you get Cyberdyne robots building Cyberdyne robots and we all know where that road leads.

Safety first! I've started wearing gloves and safety goggles when removing supports - especially from larger prints. I started doing this after drawing blood waaaay too many times (one time where I didn't notice until I saw the blood on the print itself...). And when I finally got a piece of plastic INTO my eye, where it started sneaking behind my eye, I realized that removing supports is a lot more dangerous than one would think. That plastic is darn sharp and it could cut your corneas and leave a permanent vision impairing scar. So to every aspiring maker out there: Please use gloves and safety goggles when removing supports. :)

@plan7a

2 жыл бұрын

I read your comment after I'd posted mine, but I've kept my comment as I posted it, as it can't be mentioned enough, I feel!

@adrianmalkovich7101

2 жыл бұрын

Yeah, I once had a little piece fly right into my eye and get stuck under the eyelid. It was a literal and figurative pain to get it back out (no lasting damage, fortunately). Ordered a box of cheap safety glasses from aliexpress and distributed them all over my place so I'd never have an excuse not to put one on when removing supports 😀

@CoLD.SToRAGE

2 жыл бұрын

This comment x 1,000… safety first!

@trevorpomroy550

2 жыл бұрын

Agreed!

Ladyfractic, that was awesome! I love that we see the mishaps on this journey, and so cool to print your own computer.

@RetroRecipes

2 жыл бұрын

Thank you! Mishaps are part of the journey and I feel it’s important to keep them included. ☺️

@elmariachi5133

2 жыл бұрын

You should try using an dual extrusion printer with water salvabe PVA filament for supports in future.

@Ramdileo_sys

2 жыл бұрын

@@RetroRecipes at 17:01.. well of course Perifractic can do it... I mean he just use the force.. 🤣​😂​🤡​

That is a wonderfully over-engineered case, but the moment when the keyboard fit into its recess just perfectly was very satisfying.

Some good advice: always wear (safety) glasses when removing supports ;-)

@RetroRecipes

2 жыл бұрын

It definitely crossed my mind, and my eyes. 🫣

@mal2ksc

2 жыл бұрын

Safety squints engaged!

@larsmuldjord9907

2 жыл бұрын

And gloves... :)

You now have a blood bond with your computer. Your blood is in the computer; the computer is in your blood.

I discovered this channel on the 8 bit guy's channel with the think differently challenge. The pi lle. I was born in 1970 so I grew up in the 70's and 80's and love the retro tech from my youth that you guys often showcase. Keep up the great videos!

9:30 this is the reason why i wear always safety glasses when I'm cleaning up the print. I'm glad to see this because i thought that somehow I was cursed.

The Xena theme is what got me. Hit me in the nostalgia. Happy New Year all!

it's a massive pain, but if you get reel tangles like that, unfortunately the only thing i've found to do is to re-spool it. grab an old spent spool, stick it on a spinny thing (I usually go with another spool holder or a broom handle or whatever, put the problematic spool on the printer's spool holder, and start re-spooling it... when the newly wrapped spool doesn't try to work it's way back off the spool any more, you can spin it and guide the filament back and forth along the spool to get nice even coverage across the spool.

Reminds me of a Lear Siegler ADM 3A / 3A+ - I had several when I was in College 30 years ago - I'd buy 1200 baud modems and rent them out to CIS students so they could work from their dorm rooms - that kept me in pizza and beer money for several quarters.... I'll have to build one of these!

Bravo, Ladyfratic! Fantastic episode! I can’t wait to see part 2.

A refreshing realistic video showing what can go right and wrong. Appreciated seeing the goofs and difficulties. Love what you have built so far and look forward to seeing chapter two.

I have to be honest but its the first time in MY ENTIRE life that i have seen someone build a computer with a hammer ! Its a first for me ...

Just bought a 3D printer and this video has given me food for thought. Cannot wait until episode 2. Looks like the journey is as good as the destination on this one.

top tip. if your print fails, measure the height it got to then just print the top bit by subtracting what you already printed from the z height in cura.

@RetroRecipes

2 жыл бұрын

Wow. How accurate is that?

@Fozz84

2 жыл бұрын

@@RetroRecipes Really accurate. For example if you measure the height of your failed part at 102mm just type into Cura -102 and watch the part disappear 102mm below the virtual print bed of your machine. By the way I love the show. my partner has started watching because she loves the dynamic both of you have on-set. also it reminds her of playing games when she was a kid. thanks for this. :)

@RetroRecipes

2 жыл бұрын

@@Fozz84 Awesome, thank you so much! And her ;-)

I like how the cabinet came out and I use a Flash Forge 3d printer and have had some filament tangle too .

Great video. I liked that you showed the all the little mishaps. Looking forward to watching part two, which I just found, and which pointed me to this episode. Don’t know how I missed it when you released it.

I really appreciate the ladyfractic build episodes, always fresh and fun! And first of all, full of tips and tricks! Thanks Ladyfractic!

That project took a lot of patience! I am thinking of getting a 3D printer, it has so many uses and possibilities... Great video and looking forward to Part II.

Ladyfractic doing a great job with Puppyfractic playing nurse. Loved this so much and it has a commodore pet vibe to it (that's a good thing imo) can not wait for part 2 and hope there will be more Ladyfractic videos like this in the future ofc we will let Perifractic do videos as well haha. Hope the battle scars heal up nice and roll on the next part. Take care guys and have a great weekend.

@djmips

2 жыл бұрын

Very Commodore Pet but even more the lesser known but iconic Lear Siegler ADM-3A

@djmips

2 жыл бұрын

en.wikipedia.org/wiki/ADM-3A

Love this video, it's a cool build! Pro tip! Use gloves and glasses, I've had plastic in my eyes and cut my hands during cleaning and not want to repeat that. You only have two eyes and you wanna use them as long as possible xD

This is great. Gozer the Gozerian is so amused making retro PCs that she's not trying to destroy the planet. Shandor will be so pissed! 😂

@beowulfkaine

2 жыл бұрын

OMG I was thinking the same thing!!!! Not that Gozer looked bad she was super hot, but yea, she totally looks like the Goddess!

What a neat little ADM-3A-inspired case! Some of the fun I don't have because I don't have a 3D printer. (And, well, some of the tedious cleanup work and re-work I don't have, I guess, hehe.)

Something I love about your channel, are the dogs thought bubbles.

Wow, Great job! I usually use 3d printer to rebuild missing parts for my restoration projects, but this 3d printed computer case is amazing 😁!

This project might have tested your patience, Ladyfractic, but I am sure you had a lot of fun and learned a lot. Perafractic with the pinch hit! Nice job to the both of you.

2:57 I can only imagine how frustrating 3d printer problems are. The regular old dot matrix and jet printers were bad enough when things didn't go right.

so apparently I need a heat gun and a metal spatula. I just built my Prusa I3 MK3S last weekend and I've been having trouble with supports as well. I did print my own made from scratch models the 1979 Enterprise Refit model and the Pyro-GX from the video game Descent. I also had trouble with bad filament. It's just the just that came with the printer. Thankfully, I'm past the part of the spool that was tangled on the spool.

This is how one could make the case of that ultra rare commodore model that no one seems to have.

Impressed by your patience printing and assembling the case, that plastic residue seems nasty. The case has that awesome old school terminal look, will be interesting to see how it runs.

You can take off the supports way easyer if you turn on "support roof", but you need to set Cura to show the "advanced" or "all" settings.

@DavidSpitzerLawDog

2 жыл бұрын

i used reguar supports and they came right off - no issue

print out a filament guide close th the spool, thread through it, that will prevent the filament going back and over.

I've spent waaaay to much time removing Cura supports and also hurting my knuckles (they DID result in some of the nicest supported undesides I've ever seen though I gotta admit!), so I much prefer Prusaslicer's way easier to remove supports... I made a very nice profile for the Lotmaxx Shark, so grab and install that!

Try Ziro brand filament,(yes I spelled it right lol) works great, and bridge is less a problem. I do mine at 220 degrees on the hotend. Comes silky smooth each time.

1:00 Callisto from Xena, why ? the one where they switched identity. the 3d print could have had different splits, bottom middle and top in front back, that would make it stronger and prettier. (or reverse, top middle split and bottom front back split, keyboard is the heaviest part) top part could even have more slices, not a front + back but several back parts, some even translucent (does that exist in 3d filament ?), for optional extra lighting effects ... no translucent filament then flat area cutout for clear plastic sheet, back could have it for extra wall projected logo ... custom logo is negative print on paper + cutout white parts, tip : seams could be super glued on the inside.

Ah yeah... The joy of messing around with bigger parts off a 3d-printer 😂 I ended up constructing parts in more pieces using ABS (got that dirt cheap) and avoid hangovers and supports best possible to save some sweat and blood. Kudos for going through all of this, Ladyfractic!

I've never done 3D printing before. I had no idea there could be so much slag in the process!

Wow, good for you waiting until everything is printed to do the cleanup. After my first big print, I quickly changed my support % down to 5.00, I will even go as low as 3.0%.

Ladyfractic never disappoints in her recipodes. Great project video, and excellent job cleaning up those prints. My fingers would have been non-existent after trying to remove those supports.

i often find banging the print on a table sometimes loosen the supports, cause its only held on by fine contact points, so a good shock is sometimes enough

Oh! I remember seeing the first version of that case on thingiverse and was very tempted to print it - this update looks even better! And yes, removing supports is always a major pain. Regardless, your new/old computer looks great!

It looks like an ADM terminal. Impressive job

I have seen that keyboard on Amazon for a long time now and that brand name gets me everytime. Dierya, lol.

So ladyfractic is who starts the path to The Singularity. Soon computers will reproduce like tribbles.

I have found that the Amazon Basics brand filament and the brand you were using does that a lot where it gets hung and stops feeding… I use Hatchbox filament and it prints perfect! Just a tip incase those other brands keep doing that

All things considered Ladyfractic, for a first attempt this turn out pretty friggin amazing! Took me a year to tune my 3D printer to print reliably. 👍

9:57 Blood! You have slaked the project gods' thirst! Therefore the project will turn out awesome....

I didnt know i wanted ladyfractic to host videos every once in a while!!!

@RetroRecipes

2 жыл бұрын

I have at least two more solo videos on the channel you might enjoy! - LF

Feel ya on the finger pain, seems like every retro project I do involves me banging my fingers/cutting them up and crushing my nails.

I would love to attempt something like this. With my luck, I’d end up with support spool plastic in my cornea! I can’t wait to see part 2! Way to go, Ladyfractic! 🎉

I recognize "Chopsticks" being played on a keyboard when I see it Ladyfractic!

What a fun project, the results came out great. If it helps, I've found that the filament snagging happens if it is ever let go after being opened - once it unwinds even a little, it can be difficult to uncross the filament. There are designs for 3d printed filament clips that you can use to hold it when its not loaded in the printer. Looking forward to part 2 of the series!

great job, love the way you highlighted the heaven & hell that is removing the print supports. It should be noted this is really a project about 3D printing a computer casing rather than a computer tho.

I'm surprised you didn't have a filament sensor. Mine does, but I put the magnet in backwards so it thought there was filament at all times. But I've fixed that.......only to discover that the upgrade for the multi-material upgrade (MMU2) has a different mechanism so that wasn't necessary. Same IR sensor different detection method.

I had looked at building that "Thing" awhile back, but came to my senses when I looked around the place and saw all of my other projects staring back at me accusingly.

That was so good, I think I watched it 3 times. I wonder how many people picked up on the "chopsticks" at the end. Too funny! This looks like a super fun project to do. I can't wait for part 4!

@RetroRecipes

2 жыл бұрын

Thank you so much! As I’ve been working on part two the last few days I can confidently say you’re in for an adventure! 😆-LF

@CubicleNate

2 жыл бұрын

@@RetroRecipes I am very much looking forward to it. My daughter asked if we could make a computer so thank you, LadyFractic, for inspiring my daughter in technology.

@RetroRecipes

2 жыл бұрын

I am so happy to hear that! A main goal of mine is to widen the retro and tech space and make it a welcoming place for women of all ages, from everywhere. I can’t wait to hear all about her project! - LF

For a lady with a perfect RBF, you sure have a gorgeous smile! And I admire your tenacity with this task.

Pi Computer Building! I feel I must add further warnings to everyone who'd try this for themselves, as it seems to have been overlooked in the instructions! If doing anything like this be sure to wear safety eye protection; either goggles or a face shield. Also, ensure all parts and tools are accounted for throughout, especially where animals and children are in the household! (I realise this is common sense but I feel it needs to be mentioned!). Looking forward to part two, when available.

I love the color of the plastic.

Excellent Ladyfractic. Your patience does you credit. It looks very 1970s computer terminal in style, and what might make it look more authentic are custom deeper key caps in a classic retro style font. Still. it looks amazing, and I look forward to the next part.

Thanks for sharing this. I'm tempted to build the one you made, it looks like the old remote terminal I used in college. Have you considered using a Dremel tool to clean the schmutz off the printed parts? It might not be as fun as the rip-and-wrestle approach, but you'll cut yourself less (I hope).

They were some strong supports! Just discovered your channel, now on a binge :)

Oh, I was *just* about to go ahead with printing one of this but I was not sure how the final product looked. I'm so glad you've decided to do this. It looks pretty cool actually. :) Also, "chopsticks" at 0:00.

increase the z air gap on your tree supports by a layer for easier removal.

Funny video I loved !. Btw need to play with orientations, in order to minimize supports. That top lid didn't need supports if printed vertically with a brim!. Also holes dont need supports, printer can do a little bit of bridging there!

New to the channel and...Absolute love it!!! my 40s going reset to 20 again!

The Calisto begins to realize that there is another Raspberry Pi hooked up to the printer... They begin a conversation... Their learning curve deepens and within 5 minutes they decide to build Retro Skynet... eek 😬 Seriously this looks like a lot of fun.✌️😎👍

That's a really cool project! I'm planning to make a 3D printed clamshell handheld out of a Khadas Vim 4, a Rii mini keyboard and gamepad components from 8BitDo. It may take a while to complete the project, but it's nice to see similar projects in the works. I look forward to watching Part 2!

Every plastic crunching sound made my skin crawl as I know exactly how it can go from awesome to fail art in a split second.

Emencely satisfying and genuinely delightful video. I would have probably broken down and grabbed some gloves and a Dremel tool for the clean up but obviously you powered through just fine. Lovely job and cheers to the whole Fractic crew (both in front of and behind scenes). Ready for part two!

I love that kind of project, it's always inspiring. I can't wait for part 2 now :)

This looks WONDERFUL! What a great project, thanks for sharing the build.

This looks awesome. Can't wait to see where the build goes. I love how you just shoved the electronics inside. 100% how I'd have done it. A nice honest build.

What a great project! I have two Raspberry Pis (A 8GB Extreme and a 400). I have a seven-inch LCD monitor and my brother has a 3-D printer. Looks like a great case to print to do the same thing you are doing! You have done a fantastic job so far! Look forward to part two! Sorry for the finger owies!

What an incredibly enjoyable video. I just love watching tinkering videos like this one. Makes me wish I had a 3D printer myself. Very excited for part 2. Keep it up, great work. Thank you ☺️

The age we live in... Grew up on Commodore 64, now watching videos on printing micro computers and already wondering what to do with own 3D printers... Crazy.

Very impressive. Would love to make one of these if I had a 3D printer . Excellent vid !! Great job 👏

That came out nice! I've used a lot of 3D Solutech filament without issue, so I wonder if you got a bad roll or something. It would have driven me crazy to have so many failures.

I have considered something like this for quite a while, but I kept running into a major limitation of PLA plastic: When heated, it shrinks, and not at all uniformly. I've had a few projects go by the wayside because they involved other pieces of equipment that generated heat, and so cause warpage and drooping in short order. :'(

Cool build, can't wait for part 2. Also, 01:00 can anyone else hear the absent scream? 😆

Nice! I want to make one... Will have to look into it. Thanks for sharing. Looking forward to part 2.

I’ve only seen like 45 seconds of this channel and I’m going to be addicted lol RETROOOOO

That's a pretty fantastic project. I'm thinking of doing it now.

@thecount25

2 жыл бұрын

I decide to do that other crazy one with the 4:1 monitor

Hi! I just spotted Lady Fractic in the latest Nicholas Cage movie and wanted to call it out 😄

Getting some Amiga 1200 vibes. Pretty cool stuff

Have a buddy that did this build last fall. Plenty of cleanup work, but great sturdy design.

If that was your first 3D print project, you should be canonized for sainthood, Ladyfractic. Especially given every 3D printer model has different tolerances, that looked like a PITA. Really neat result though. Looking forward to seeing it running in Part 2. 👍️

Great video. I think I’m going to have a go at this myself. I will avoid using Amazon though as the employees aren’t treated well by their jerk of a boss. Thanks for the video 👍👍👍

Great project. I recon I might look at designing one up based around the Pi 400

Watching these videos makes so want to do something like this... I really enjoy these builds.

I'm really glad KZread recommended me this video! You have a new sub. :) Can't wait for part 2!

Hey wait, the "Ladyfracintosh"-monitor is basically a 3D model of a ViewSonic-monitor! There just so happens to be one standing around here. 😉

Absolutely love this video, thank you .. ❤❤❤ ❤❤

Fantastic work there Ladyfractic, that’s a super cool project. Looks like you need a printer that can detect broken or spent filament so it stops and waits for you to fix the problem before resuming where left off, could save a lot of time and frustration. Can’t wait for the next recipode.

Perifractic is so lucky to have someone who shares his interests!

im thinking making a modified screen bezel to adapt a 7 inch more popular screen and available on amazon or ebay

Great Video. You may want to double check the Display PCB it looks like you may have it plugged in upside-down.

practice makes perfect they say well done ms cheers from uk.....