A more concentrated flame, smaller area,40years experience, even heat,even distortion. Love your videos, simplifying things for the diy

I really like Trev's 'flavor'. He has a mellow approach to his work, and you can see that his perception just gets right in there and he always knows how things are going. I am not at his level, but i strive for just such a focused approach where you keep correcting it until it is pretty dialed in.

Back in 77, (old school), I was taught how to remove stretched spots, (high Spots), in fender panels with only a rosebud tip to heat with, and a wet rag to quench with. I could literally hear the panel pop back into place while doing so. Its a bit of artwork to achieve and does take practice but in most cases, I did not need to hammer at all. I actually became quite good at doing so in under a day. I simply heated and quenched strategically. Its all about understanding what caused the stretch and where to heat to remove it. Small circular dents were easy. The skillful part was removing an oval or even curved stretch. As for the hammering, I was also taught to angle my hammer taps with strokes going inward towards the center of the high spot, from all angles around the high spot, not to hammer directly downward on the high spot.

@James-lg5lw

5 жыл бұрын

Dave Boling Do you have a video of your technique?

The science of what's going on explanation really adds value and appeal. More that. pls.

Top job Mate. I've learned so much from your wealth of knowledge and experience. I have been in paintless dent repair for 25 years and always try to increase my abilities. Thank you.

@trevsblog

Жыл бұрын

Thanks for your comment, PDR has always impressed me greatly. Cheers Trev 👍

Easiest way to tell a quality tradesman, they make it look easy! Make you think I can do that. Which is exactly what you've done. Having been in the painting/panel industry many years ago I know I can't do this, but I'll find some scrap and try it 👌 awesome work mate, pleasure to watch.

Time spent watching your videos is time well spent. 😆

Just fixed the wavy bonnet on my 1960 Falcon using a blow torch and a few basic tools thanks to your blog. Always been into welding, but not panel beating, never thought I be able to shrink. Cheers

@trevsblog

Жыл бұрын

Glad to have been of help. Cheers Trev 👍

This is one of very few channels where I learn something and don’t judge say this guy doesn’t know what he is doing. Very good teacher

I’m looking at an old Dodge a108 Xplorer and anticipate building some rocker repair panels, a door bottom and tackling some dreaded A-pillar rust. Your channel is an inspiration!

Definitely love the DIY tools. Much better than hundreds of dollars in less effective name brands. As a request, I would like to see a cut-out and patch welded in. I've seen others on youtube but I would like to see how you do it just cause you seem to explain the processes better. Thank you for your efforts they really are helpful.

@donitmyself8935

5 жыл бұрын

Nevermind on that request I just saw Old School Gas welding video. Very helpful. Go figure as soon as I comment, the next video I watch is what I needed.

I really appreciate your work to show how the light shows the high and low spots. Not easy to see on the camera but easy to understand. It is obvious you take a lot of effort in your filming, thank you.

Looks like it can oil can is what we call it,thank you Trevor, shrinking metal is an art.

Ive been a painter for over 20 years... Now starting to do full frame off restorations... Ive been hard pressed to find quality craftsmen in my area or in canaduh period.. Ive recently subbed to your channel and your ability is awesome... I love to learn from talented craftsmen. Thanks Trev!

The advantage of an oxygen acetylene system is you can make pin shrinks (tiny spots, very localized heat) . A dolly backup might help when you hammer, but that's always been my approach and I don't know everything. Very interesting the way you are doing it. Cheers from Canada !

Sir, you are a living God!

As always fantastic , I couldn’t. Help laughing.....the weld breaks and you knock yourself out with that slide hammer , I wouldn’t want it too happen but thanks for titalating my humour 🥳🥳

A 13:00 you admit that shrinking went too far and is now a low spot. Then you find a new oilcan. This is where you use the hammer to bring the low spot up, hopefully pulling on the oilcan and eliminating it

Great video. In the late 50's, yeah, I am that old, the method I was taught to use to shrink panels, was to use the acetylene torch and actually heat the spot I wanted to shrink to a cherry red, before cooling with a wet rag and then hammering. It is interesting to learn that the process might have worked at a much lower temperature. I was doing a chop and channel on a 34 Ford pickup, and because of the hard life the truck had lived, there were a lot of dings, some about quarter sized, that had to be shrunk back into shape. The bodyman that taught me was a master with working metal, and like you, he used a lot of finesse to straighten even severe dents. You do great work, and I am looking forward to watching more of your videos.

@trevsblog

Жыл бұрын

In some respects I wish I hadn’t made this video using a blow lamp. I actually made this video as a request by someone that only had a blow lamp as a heat source. Using a O/A torch is more effective as it creates a smaller spot of heat. Having said this it’s actually possible to use a hot air gun to shrink metal if you use it to expand the panel in an area before giving it a blow with the panel hammer, the heat expansion holds the panel ridged placing compression along in when hit with the hammer forcing it to shrink, a bit like a mechanical Shrinker. By far the most useful for me is a single sided spot welder. Thanks for your comments. 👍

You truly are the magicians of the motor trade. The nuts and bolts brigade is easy peasy by comparison. Cheers and keep up the great tutorials. Regards Peter A.

I've just recently been introduced to your channel and I'm delighted to be enlightened by your knowledge. You have a great teaching style, patience in both your work and explanations. Thank you for taking the time to do this 👍🏻

Love you too Trev. Therefore I just want to echo Papa Bob's comment so you're still with us for a very long time. I took a few semesters of welding from an adult education class in a local high school, and the bit about butane lighters being dangerous is serious stuff. I dimly recall the story of a welder on the Canadian railroad who died when a bit of welding spark went through his shirt pocket and set off his lighter. Poor chap. Be well and physically distance yourself from the damn virus, (and those lighters!).

Another mine of information, janner! Love that old weight!

Ha Ha. I was wondering what a blowlamp was. Its a propane torch! Ha Ha excellent! Great vid as always Trev. From across the pond here in California.

Hi Trev Regards from NZ enjoy your Blogs, straightening metals is always a patience game I have been in the metal fabrication game all my working career Ships trucks Tanks etc What one has to keep in mind firstly is that steel plate has been Mill manufactured, heated & rolled Quenched Etc which imparts Locked in residual stresses Thinner plate usually the worst as heavy plate cools slower and partially stress relieves itself Then the user forms, Heats Welds as well and releases and forms more stresses to form distortion Keep up the great information blog Its all about experience and Listening well done mate

Great video! I needed a close up explanation of this hammer heat technique. Now I can take on some hail damage on my hood. Cheers!

Fascinating watching you shrink that dented panel, very skilful thanks !

I like to use tig welder as my heat source its very very controlled with practice especially on stainless trim from the old cars

Enjoyed that. Looking forward to the compressor drier.

Trev beautiful job. The wagon is looking great.

I seem to remember my dad who was a sheet metal worker saying you can also take high spots out by using a torch turning the area red and then rapidly cooling the are with a cold wet rag. He also did it the way you showed. Great video many thanks.

Thanks for keeping the art alive Trev! Your a real craftsman!!!

Trev you amaze me with the skills you have got Thanks a lot

Amazing work your doing making all these panels very nice work Trev.

Super job Trev! I've got an oil canning patch on a mower cutting deck I've made out of 2mm steel and will give this trick a try this weekend. Cheers!

Another brilliant video by a great craftsman,. well done Trev,..love your work !

Brilliant mate. Simply brilliant!

No doubt Trev ,your blog is most informative . THANKYOU again . Good music as well

The Van of Theseus. Amazing work!

More Very High Quality from a Professional. Thanks for sharing !

Very good demo on shrinking!

Another great video, you explained the shrinking process really well, and your home made tools are fascinating. Thanks for another quality video.

So nice to see true tradesmanship in this day and age, thanks!

Thanks this video took me back to the old school.I appreciate you and your knowledge.i will definitely watch many more of your videos

Subscribed, I've watched many video's of this type and Trev is by far the best. The tools are genius, I also make them as needed. Love the the slide hammer at the end,I made a clamp ended variation of this a while back to sandwich the weld on type dent puller studs which allowed me to move around on the dent and pull from all, center or either side as needed. Thanks for sharing your skills and knowledge!!

Thanks for that ,great instructions on how to. That dryer sounds like a great idea.

Thank You. You are an excellent teacher. I appreciate the time and effort to teach us mere mortals.

Great job, I am learning so much from you. Love the Outro music

Awesome metal work. Good job

I like you explanation Trev. Nice work.

Thank you Trev, great video!

From one Trevor to another Trevor, great work... ive been using ur tips and tricks to rebuild my no.3 of 150 MGF abingdon vvc. You are helping me save the car using all my own hands. Every corner and sill fabricated and welded better than new. Thanks so much.... T.

Another interesting post! I've used heat shrink to straighten shafts, after a weld repair, but just used a water or air quench. Love the homemade tools. Seems like the work is more fun when done with them. Thanks!

Ah! I think I get the heat shrinking concept now! Thanks! Al in USA

Great vid, really helpful thanks ✨👍 I’m doing a epic resto on a 61 VW Splitscreen & kids had been jumping on the roof, so lots of panel beating

Good gravy Trev, it works! I found a previous repair last night on the tail panel of my Firebird so I decided to pop the filler out and repair the dent, unfortunately, I pounded the metal a little thin and it had the feel of a pop tin, so this morning I watched your video and tried it and with 2 minutes and 2 tries it was back straight, nice and tight, it worked perfectly. Thanks for the awesome tip! Cheers

I remember my dad trying to explain to me how to shrink high spots and it wasn't getting in. Maybe i'm a bit thick but the way you showed gave me hope. Thanks much, so interesting.

Amazing knowledge brother!!! Thanks for sharing!!! I Love your channel!👍🏼👍🏼

Thanks. Brilliant again. A real pro. Love the homemade tool ideas.

thats the way I leaned about 40 years ago. But sometimes I use a shrinking hammer

Your channel is gold!!!

Another great video mate. Many thanks.

another great video .. i better get on and try your tips on my mini van back doors and see if i can save them ..

Great video. I love making my own tools. 👍👍👍

Great video ! It works great and easier than i thought . Had to relocate the tank filler spot on my bedford .welded the ring in for the fillercap .was al warped .thanks for the great video . greetings from Holland

Thank you for the large puller idea. Have a large thin flat panel with no rear access and didn't want to spend on a spotter.

Love ur work bro. Many years ago I use to work in the trade and worked with a body man that use to build AC cobras etc in Uk. So use to watch his work. Thank u.

When dad did a shrink (oxy acet, so it was faster). He always held a dolly "around" the edge of the shrink as he tapped it. Then he moved the dolly gradually into the shrink to move the metal back to the profile. I was the kid inside the panel holding the dolly when he couldn't reach the spot.😉

Great video 👍 hope all young beaters will find it very helpful like myself. You can't find those informations on the spotter datasheet 😂 Some people like you had to spend years to learn this the hardest way we have it on the plate. Hope will be much appreciated. Regards Mike

Super informative. Well delivered. Subscribed. Thank you

These are bloody excellent. Many thanks.

Great video. I was just trying to shrink excess metal from a panel today, but was unsuccessful. It is "tramping" as I call it, but the same thing, it's high to begin with but will flip to a low point if I push it. A couple of things that will make a difference is that my butane torch does not produce a fine, pointed flame like yours. It makes the heated area twice the size. Plus, I was just quenching it, I wasn't tapping it while it was hot. I'll be having another go in the morning. I really enjoyed the video and the way you explain things, so I've subscribed and look forward to any future videos. Cheers.

@trevsblog

4 жыл бұрын

Ray Plant by putting the heat into the area you are actually expanding the metal, this expansion causes a lot of tension allowing you to hammer the metal without it popping back in. When you hammer it, it causes the metal to shrink. The quenching isn’t as important as it appears as I’m mostly using this to bring the temperature down so that I can inspect the repair. Cheers Trev 👍

@RayPlant77

4 жыл бұрын

@@trevsblog cheers Trev, I appreciate your response. I'm about to give it another go right now. Thanks.

great job trev

Thanks for all your interesting tips I'm already put it all to use

A very helpful video. Many Thanks.

Thanks for your work. Great tools.

Great stuff here! So many great tips and tricks. I'm sub'd now.

Like your work! I am in Australia and really find your videos most helpful. Cheers

@trevsblog

5 жыл бұрын

dave coate Hey Thanks Dave. Cheers Trev 👍

`My God!!! I'm absolutely in awe!!! Love your channel!!!

You sold me on the intro video Subbed

Love your work bud👍👍

So enjoyable to watch, i hate heatshrinking but it must be done most of the time. Great tips and tricks. Love the home made tools to. Thanks Trev.

@trevsblog

5 жыл бұрын

Peter Goodwin Hey Thanks 🤩

@petergoodwin2465

5 жыл бұрын

@@trevsblog you are the best trev . So well explained . Sometimes this can drive you mad especially on a massive roof . Have a good weekend mate .

You need to be the next Dr.Who! Seriously you would be smashing.

You really explains very well without no fix, frestelsen Done, Thomas Sweden ❤️

@1979ascona

4 жыл бұрын

Fuck auto translation, hahaha! 😁

Im finding new stuff to me Trev. This is great as usual. I love the clock and tin man you made. The vespa model is superb too. Thanks for what you do. Im going to look for your video where you use some copper. Cheers col

@colinlyne1660

9 ай бұрын

Ive fashiened a panel for the jacking point on my suzuki wagon R rear sill arch area using your advice and explanations. Thanks ever so much Trev

your a master autoplateworker good video and never understand I my father when me said (making hot here make hot there) and Inot understand it and all this is for expancion an crimping wow Ive learn today a thing bye

Another awesome video! Thank you.

@trevsblog

Жыл бұрын

Hey thanks 👍

Good video Trev that will help me a lot with my build, I have a high spot I have been trying and trying to get rid of I will try this now thanks mate

@trevsblog

5 жыл бұрын

Neville Nevstoy Brilliant I one it works for you. Cheers Trev 👍

Like your style trev

Very helpful. Will use on my 57 Bel Air.

Hi Trev . Thanks for that great vid. Good to see you back on your project. Have really learnt something today , as when we have the odd panel that has been stretched due to a large quantity of holes , we have heated an area and rapidly cooled with water then dress out with panel hammer to flat. sometimes it works well sometimes not so . Will bear in mind your Vid . Keep it up .look forward to the next vid.Regards Don

@trevsblog

5 жыл бұрын

Don Codman Don just bear in mind I only cool the panel in order to bring the whole repaired area back down to room temp before checking the repair, even the slightest bit of heat still remaining in the panel can make it warp. When using a flame always hit the heated area as soon as it is heated, then let it cool to check your repair. I’m planning on doing more heat shrinking videos in the future and will include lots of theory as well. Cheers Trev 👍

this is something that i tried a few years ago unsuccessfully. now i know that i was doing the hammering part wrong (i was using a dolly behind it and just stretching it further) so thank you for filling that gap in my knowledge.

@keithdouglas4581

4 жыл бұрын

You were doing it correctly,the idea is to heat up the metal to a small red spot and then with a hammer and dolly gently planish around the circumference of the red spot which has the effect that as the hammer hits where the dolly is it sqeeezes the metal into the red dot thereby shrinking the panel.I learnt how to do it in the 1960s as an apprentice panel beater.

Very very interesting to see thank you

Hi Trev, just watched your interesting blog on heat shrinking a panel. As a plumber l noticed that you are holding the flame a bit to close to the metal. the hottest part of the flame is the tip of the dark blue cone, the flame is not so effective if the cone impinges on the metal. otherwise a good blog.

I feel like this channel should have a lot more subscribers than it does

@walkertongdee

5 жыл бұрын

It will have

Fantastic music!

Great video ,I got a lot outta this

I like the fact you make your own tool's I had to do that to with many diffrent dolly shapes of metals for diffrent corners.

@trevsblog

5 жыл бұрын

SNOOP U 2 Hey Thanks 🤩. Your comment is very much appreciated. Cheers Trev 👍

Great , Great video, Thank you.

Good tip for you when welding a pull bar [20:20] run a weld to panel first then weld bar on to weld so after work you do not damage panel when removing bar [often pit marks /holes ]