Thank u 4 sharing💪🏼💪🏼💪🏼👍🏽👍🏽🤲🏽🤲🏽🤲🏽🤲🏽🤲🏽🤲🏽

Best information for headlight lense removal

Hello, what product did you use for the silicone remover in the syringe injection?

wow

where can i buy cover headlamp preve. thx

Thanks brother ❤️ 🙏

guna cecair apa tu bos

E60 punya cover tukar berapa u charge boss?

from what I've seen, the oven method is best, faster to to take apart and clean out the old seal

@rdmalaysia8187

Жыл бұрын

Not all headlight suitable for oven method

How do you get the new headlamp cover for replacement? I wanted to change my headlamp cover as well... now having some heat line crack... any suggestion to fix it?

@rdmalaysia8187

3 жыл бұрын

Market don’t have cover for preve. You can look for a shop to polish back the cover.

@cleanishmk5853

2 жыл бұрын

Ebay

@jayasankarjs4767

2 жыл бұрын

Available in ali express

For the life of me, I cannot find one of these for my car, but every one I see shows that you need a *LOT* more than just the replacement lens to fix this.... You need *heat guns* / *cover openers* / *seal knives* / *seal remover* / *sealant* too, just to swap this thing out. So, for those of you thinking this is a cheap alternative to replacing the entire *headlight assembly,* think again, because by the time you by the *twenty toolboxes full of stuff you will need to replace the lens,* you *could have bought 3-4 full assemblies!!*

@shoe1126

3 жыл бұрын

And its a lot of work, but thats the fun part

@ms.shunte8323

2 жыл бұрын

Try the baking technique. I used the heat gun and it took too long. Baked in the oven @240 degrees for 15 minutes and it popped right off. I did use 2 knives and 2 flat heads.

@shoe1126

2 жыл бұрын

@@ms.shunte8323 heat gun took me around 10 min for eachbheadlight, started at one side and worked my way along with trim remover tools

@ms.shunte8323

2 жыл бұрын

@@shoe1126 I tried both ways. The heat gun was actual work time. So 10 minutes of actual work time versus 15 minutes of bake no work. And 2 minutes of work.

@shoe1126

2 жыл бұрын

@@ms.shunte8323 i see, very cool, ill probbtry oven if i do it again, but you have to remove all the wiring then right?

i got kia sorento and one headlight adjustment motor is toast (it doing whining and scratching noise all the time but liht working fine) but seems the damn thing is located inside headlight

@rdmalaysia8187

2 жыл бұрын

Then have to do operation on headlights

Is it the samething for doing it on a 2002 dodge Ram 1500

@rdmalaysia8187

Жыл бұрын

Basically is same

Hi boss can u repair the Carryboy G3 LED break light

@rdmalaysia8187

2 жыл бұрын

Never done it before . Can’t give firm answer

boss demo cara buka mini cooper headlight...

@rdmalaysia8187

3 жыл бұрын

Kalau Kita ada headlights mini. Definitely can try on it

boss ada try buka lampu belakang neo x boss?

@rdmalaysia8187

2 жыл бұрын

Belum ad peluang

At what speed you use your heatgun on to soften the seals of the headlights

@rdmalaysia8187

2 жыл бұрын

Depend on your experience using heatgun Different brand of heatgun got different method

How would u open side car fender indicators they not rubber sealed they factory glued

@rdmalaysia8187

2 жыл бұрын

Cut and seal back

@TW39

2 жыл бұрын

Will a hot knife work

@rdmalaysia8187

2 жыл бұрын

@@TW39 yes. Can be use

wht is the product you use to seal the headlight

@rdmalaysia8187

Ай бұрын

Sika

please make a video how to open headlamp dmax ..

@rdmalaysia8187

5 жыл бұрын

We will do if we got a d-max head light. But it's about the same way.

@swingking08

4 жыл бұрын

Same process haha

should of polished the lens

Boss new proton persona iriz headlamp also permaseal ya? Or butyl

@tzershernkhaw

3 жыл бұрын

Also where did u get the clamps ya. Thanks!

@rdmalaysia8187

3 жыл бұрын

@@tzershernkhaw nowadays, mostly glue will be butyl. Easy to open. For the clip, we get from Ali express

may i know where you bought the Preve headlight cover..

@rdmalaysia8187

3 жыл бұрын

Yogananth Subramaniam no preve cover sell in market

Rearlamp can do? Remove cover.

myvi punya cover headlight boleh buat ke ?

@rdmalaysia8187

2 жыл бұрын

Boleh

Where to buy seal remover?

@rdmalaysia8187

4 жыл бұрын

Harry Crawler can look into Ali express

kalau cover hitam tu dah banyak bengkok sbb guna heatgun terlalu panas, macamana nak bagi straight balik atau repair balik?,guna heat gun lagi ke?

@rdmalaysia8187

2 жыл бұрын

Tengok betapa serious kerosakan Boleh recover balik Guna heat gun

@norbayaetty4391

2 жыл бұрын

@@rdmalaysia8187 Ada kedai Ka boss?dkt mana

how long it will lasting before water/moisture get in again?

@rdmalaysia8187

2 жыл бұрын

Depend on the reseal skill and the glue using

Hey guys, where I can get the green seal removing knives? Thanks

@rdmalaysia8187

5 жыл бұрын

u can get it through online. Mine bought from tao bao.

@tyenty

5 жыл бұрын

@@rdmalaysia8187 Could U please send me the link? It's very hard to find it. thx

@rdmalaysia8187

5 жыл бұрын

@@tyenty item.taobao.com/item.htm?spm=a230r.1.14.19.c7704f6fTwmw9G&id=521225682500&ns=1&abbucket=1#detail

@tyenty

5 жыл бұрын

@@rdmalaysia8187 Thank a lot man, I just found the same on Aliexpress too. ;-)

@rdmalaysia8187

4 жыл бұрын

@@tyenty you're most welcome.

mana nak cari.cover plastic headlamp tu?

@rdmalaysia8187

5 жыл бұрын

Hi, u can't get the plastic cover individual. Only can get entire headlamp.

Can i use hair dryer ?

@rdmalaysia8187

3 жыл бұрын

We do know got someone able to open using hair dryer, but we don’t know outcome

Ada jual tak tu cover saja boss

@rdmalaysia8187

2 ай бұрын

Tak Ada

How much chg re seal cover new

@rdmalaysia8187

3 жыл бұрын

No cover to be sell in market

heatgun temp set at what degree?

@rdmalaysia8187

3 ай бұрын

Base on experience

product name of the sealant? thanks

@rdmalaysia8187

Жыл бұрын

Sikaflex 255

Did you use a silicone sealant???

@rdmalaysia8187

2 жыл бұрын

Yes

@mo198832

2 жыл бұрын

@@rdmalaysia8187 because in my work they sell the brand 3M silicone sealer will that be enough

@rdmalaysia8187

2 жыл бұрын

@@mo198832 actually main issues is the way to seal it back Which type or brand doesn’t play the main role

What kind of sealer u used

@rdmalaysia8187

5 жыл бұрын

Industrial sealant.

@faraazabbasi4101

4 жыл бұрын

@@rdmalaysia8187 dear please tell me the chemical name who open light mirror without hear

@faraazabbasi4101

4 жыл бұрын

@@rdmalaysia8187 without heat

@rdmalaysia8187

4 жыл бұрын

open headlight cover must using heat or heat gun.

Hai boss kat mana bole beli cover headlamp tu?susah la cari

@rdmalaysia8187

2 жыл бұрын

Tak ada jual Preve cover dalam market

@oyazarif1994

2 жыл бұрын

I punya dah pecah berlubang…ada cara lain tak?

@rdmalaysia8187

2 жыл бұрын

@@oyazarif1994 dah lubang tak ada pilihan. Tukar lampu 2nd hand

macam mana nak cuci silicone tu..guna pisau pon masih susah. mencabar juga

@rdmalaysia8187

3 жыл бұрын

Guna heat gun panas dulu silicone, ia akan Lembut sikit, senang sikit Nak bersih. Tapi masih susah juga. Kena perlahan buat

@syedruslisyedabubakar5956

3 ай бұрын

Boleh Saya tau beli dekat mana ya clear cover headlamp preve?

where can buy this silicon can give produce name

@rdmalaysia8187

3 жыл бұрын

Sikaflex 255.

@hugolee9113

3 жыл бұрын

@@rdmalaysia8187 tq

Can please share with me what is the product for headlamp sealant?

@rdmalaysia8187

2 жыл бұрын

255 sikaflex

seal knife tu bila dri mna?sya cri kat shopee tk jumpa

@rdmalaysia8187

3 жыл бұрын

Beli Di Ali express

@vivitionnvidia7716

3 жыл бұрын

@@rdmalaysia8187 ohh okay2 tq

What is the name of the liquid in 2:48?

@rdmalaysia8187

3 жыл бұрын

Permaseal glue remover

@sawomirsawiacy5767

Жыл бұрын

@@rdmalaysia8187 Could you tell me please which one of product have you used (name of product and producer)?

kalau hantar kedai ni, berapa upah labour dia cas untuk tukar headlamp cover ini ya?

@SSW2488

2 жыл бұрын

RM300

@highiq145

2 жыл бұрын

@@SSW2488 terima kasih atas jawapan..apa apapun saya dah diy dan buat sendiri pakai clear coat. paling murah survey kedai ada nk buat rm150 upah. cuma, masalah barang tu, xoriginal mcm import.ramai nasihat jgn tukar lens.so xjadi tukar

@SSW2488

2 жыл бұрын

@@highiq145 dekat mana kedai RM150 tu bro

@highiq145

2 жыл бұрын

@@SSW2488 dkt melaka..ni labour saja.parts harga lain. tpi ni paling murah.memang standard rm200 ke rm300. sebab pasang ni, memang leceh. klau x btul pasang, mau air masuk.

what is this liquid in the syringe?

@rdmalaysia8187

3 жыл бұрын

Glue remover

@lukash2bmx

3 жыл бұрын

@@rdmalaysia8187 can you provide the name or manufacturer of this preparation?

@rdmalaysia8187

3 жыл бұрын

@@lukash2bmx we don’t have any name in English /Malay. We purchase at Ali express. Just search for 冷胶分离液

what the name gum sealant？

@rdmalaysia8187

2 жыл бұрын

Sikaflex 255

@jennzhiangzhou986

2 жыл бұрын

@@rdmalaysia8187 tq

Berapa harga heatgun? Guna hairdryer bole ke

@rdmalaysia8187

3 жыл бұрын

Muhd Hafifi Hafiz RM 100++ pun boleh dapat. Hair dryer memang tak boleh

@muhdhafifihafiz1292

3 жыл бұрын

@@rdmalaysia8187 tq bossku

What is the name of the sealant?

@rdmalaysia8187

3 жыл бұрын

Sikaflex 255

I see in other yt, they can open by dipping in hot water. Is it hoax or truth?

@rdmalaysia8187

4 жыл бұрын

Kendi Larang depends on headlamp glue. Not all can using same method

@rudolfhuijs4526

4 жыл бұрын

No mate, using focused heat you only heat the border where the permaseal is applied. Never use water, it gets through to parts and places you don't know when and how will dry. All the sealing purpose is to avoid water, dust and fumes from engine to get into the lenses. You can even use your normal stove oven to heat the entire piece. Make sure you remove wiring harness or any wire, bulbs and any removable piece before taking it into the oven. Set your oven at around 120 - 140 C for 15 minutes. Turn it off and then put your headlamp inside the oven. Put a cardboard piece as a base to avoid dripping and prevent your plastics to touch metal directly. Usually it takes from 10 to 15 minutes for the sealant to get soft. Use protective gloves and try prying it open with the appropiate tools. If the sealant is like thick chewing gum, sticky, chances are you made it really good. Please check your headlamp frequently, don't leave it without constant checks. Some manufacturers may have thinner plastics and they risk melting. Once the HL is opened, clean and take out the old sealant when it is still hot, this will save you a pain the rear. Once again, NEVER use hot water. Keep the thing dry.

@rdmalaysia8187

4 жыл бұрын

“Oven opening” is a good way to open headlights. Unfortunately, it’s not working at all on permaseal glue.

Boss I want to change lens for my polo, can you do? & how much do you charge? Do you have whatsapp?

Boleh tolong buat kereta saya ke?

@rdmalaysia8187

Жыл бұрын

Pm fb page kita(rd Malaysia) untuk appointments

@dujangempire

Жыл бұрын

@@rdmalaysia8187 ok boss.tq boss

This does not work if your headlights are sealed with silicone

@rdmalaysia8187

3 жыл бұрын

It’s works fine with us

@beletruz

3 жыл бұрын

@@rdmalaysia8187 silicone does not react to heat...

@rdmalaysia8187

3 жыл бұрын

@@beletruz not using heat to melt silicone. Heat is for soften headlights cover, so put in something to open it up

@beletruz

3 жыл бұрын

@@rdmalaysia8187 I was refering to the fact that most OEM headlights come sealed with mastic wich melts when heated. And most AM headlights come sealed with a silicone that is easier to be melted with a chemical rather than just heat and force (happy holidays btw! :) )

@rdmalaysia8187

3 жыл бұрын

@@beletruz understood your statement. Heat really can’t melt the permaseal silicone. In this video, we using acid to soften the silicone, and with our skill (the forcing that you mention) able to open smoothly (definitely not easy) Thanks for your sharing and advise

Put it in the oven man , you are gonna save a lot of time

@rdmalaysia8187

3 жыл бұрын

Al83rt Salazar actually we manage to using the same timing as using oven. Btw, thanks a lot for your suggestion

@davchungcpy

2 жыл бұрын

What is the recommented temperature setting and duration? Will that damage the lense coating?

pm me plss

@rdmalaysia8187

3 жыл бұрын

Pm for ?

If you appreciate your skin integrity, never wear short pants when using a heat gun, knife, cutters or handling potential scratching parts like the ones in headlamps. Besides showing the "how to", observe and recommend security before doing anything. Good instructional video.

@rdmalaysia8187

4 жыл бұрын

Rudolf Huijs Thanks for your advise and concern, we will improve on this

@alinuhad1969

4 жыл бұрын

It called Safety not Security

Jeez less crappy irritating music more talking thumbs down!!