Thank you for this. I just received my DSO2C10. Gotta love Amazon Prime Day. I was able to buy some really cool stuff (a programmable linear power supply, a signal generator and more) and saved a lot of money. This is my first oscilloscope and your video made this scope a lot less intimidating. Clearly I have lots to learn! Videos like this go a long way in taming the mystery of things new to me. Thanks a million!

It’s a weird thing CHF I have it also but lack the swelling. I’m used to seeing the large ankles and swollen limbs from my time in the fire department and the ambulance service. I was very surprised when the heart doctor told me that both sides of my heart failed. I got so bad I couldn’t walk ten feet without stoping. I have recovered some but still have difficulty breathing. The only thing I really could do was watch videos for the first 8 months my ER rate was 10 it’s now about 40 according to the docs. I enjoy watching your videos. The morons seem to do stupid comments on all channels which is sad instead of saying thanks for putting out a video to the creators they would rather insult them. I’m here to say some of us appreciate and understand the commitment to making videos.once again thanks for sharing your knowledge of this subject.

@learnelectronics

3 жыл бұрын

Thank you, I'll keep you in my prayers.

Just ordered the DSO2D15, looking forward to learning the basics. I’ve been looking at the instructional videos on this site, and really appreciate your work. Thanks for the review!

@GMC997

3 жыл бұрын

Hey, could you tell me how you like the DSO2D15 so far? I want to buy exactly this model, but everyone bashes Hantek as a brand and tells me to buy a more expensive Rigol instead. So I would really appreciate it if you could give me your 2 cents about it.

@pedromillan927

3 жыл бұрын

@@GMC997 PPl likes rigol bcs economic series from hantek scope only has a 66mhz real band... from 70 to 200mhz is software display decomposed wave

@GMC997

3 жыл бұрын

@@pedromillan927 Intresting. So it calculates the frequencies with some kind of Fourier transformation? I'm still a novice and haven't reached this deep level of understanding yet. Thank you for your response!

@g7k993

2 жыл бұрын

@@GMC997 which one did you buy? 👀

Thank you for making this! Your video was the deciding push for me, I’ve ordered my first scope!

@martinkuliza

2 жыл бұрын

Enjoy it mate my first scope was ages ago... Decades.. but a first scope is always a cool thing My advice, Take a month of work Lock yourself in a room with about 50 cups of coffee and some PCB's and go fucking nuts LOL

Enjoyed. I never had a scope before and this is my first. I ordered it and then saw your video. Stimulus came and I ordered this, Hakko iron, and Hakko desoldering gun. Wish me lots of luck!

It has pretty much the same features as my entry level Siglent SDS 1102 DL+ Scope. Cool video, thanks Paul.

I was surprised to see that much shielding on a sub $300 scope add in I2c and cann protocol decoding and this scope could scoop up a big chunk of the hobby market. I am curious if it is really capable of hitting all of its claims but I also know very few hobbiests would ever need a scope at the high end. Great video as always Paul.

Great review Paul. I have the DSO2D15, this has the frequency generator. I haven't tried it yet, but i am looking forward too. #StaySafe

Nice review video

When I started in electronics all I had for equipment was a multimeter. When I got my own scope I knew I was in the big leagues, and I figured out how to use it for everything. But these days I barely use a scope. With all of the $60 sig gens, spectrum analyzers, (TinySA,) and network analyzers, (NanoVNA,) with ever more features that I have now, it seems like my 200 MHz O'scope just gathers dust. I seldom even use the multimeter anymore, either, except for quick continuity tests. We now live in a golden age of sophisticated, tiny, inexpensive, USB or battery-powered, high frequency test and measurement equipment. Life is good.

I had a DSO5102P as my main scope for three years until recently. Hantec makes really good inexpensive scopes with good features. This scope seems to have a faster processor than the 5100 series, but seems "chopped" in other areas, like the hardware counter not displaying :( During the I2C decode, it looked like it was at 25kS a/s and 4k. Is that the most mem points and speed it can do for I2C? If so, going above 100k I2C will not be possible :( What about SPI? Can you use the EXT port for the clock-in? Thanks.

Nice review, ordered my one today :-)

Very well explained

Hi! Thanks for your review. I’m thinking of getting one oscilloscope but not sure if I should get DSO5102P or DSO2C10.

nice video have you updated the firmware ? when i try to do it it says insert USB and i do but nothing happen

Thanks for the video. If you were to compare this one against the DSO5102p, which one would you say it is a better oscilloscope? Thanks Pedro

i got this today 😌 I'm so Happy now 🎉️

That button test is cool. I am not sure how often buttons go bad on budget scopes but certain buttons get used a lot and it's nice to have a test.

This is great at this price...I can use that I2c decode on my pico projects.

I want to buy the same oscilloscope but with the signal generator built-in because I don't have that either, would you recommend this scope for me with the signal generator? I'm only doing Arduino, Raspberry Pi & ESP8266 projects and I need a way to measure the resonant frequency of tesla coils that I'm building, is this one up for that task?

I read that it is have software issue and they bring update to it . When you recall there is a bluer wave in the background you may not notice Thanks for reviewing

Looks like another good scope. Think the reference saved waveform was displayed but not easy to see.

when a n or p type semiconductor frys does it become a new ion or do the atoms move comepletly in location staying stable or i guess what ion to even use... do you really think beta particles are electron pieces or just radiation that effects the electrons spin resulting in chage in charge or weigjt or density which is relative. just a good question i was thinking about al and lead or tin or would it be too radioactive? anyhow really trying to understand the homack n electroysis in full its a bit mystic still

I like quiet test gear! Nice video thx

I have an older version, the range switches on the probes failed , the voltage measuring after many self calibration, still inaccurate and when emailed the company 2 times (still under warranty) did not respond!!

I bought this scope and I am going to use it for working on vintage audio gear. I am new to electronics and I would like to know if I will be able to generate and trace a signal at the same time with this unit?

thank you for video demonstration

Hantek makes the BEST value scopes hands down. I ordered the 70mhz 4072C but they sent me the 5202 MSO by accident so I got the 200Mhz version which sells for over 400 for about 300. Not only that but in Germany Voltcraft sells that scope for 800+ through Conrad. I used the money I saved to buy the Signal Gen which the 5000 Series is missing compared to the 4000C but I came out way on top because now I have 2+1 channels of 60Mhz instead of 1 20Mhz If I buy another scope any time soon it will be a Hantek 7000 series.

Excellent video! But I have a doubt. Please, can you check for me if it is possible to measure the phase angle between two sinusoidals with this equipment? That is, what is the phase angle between channels 1 and 2 when both channels have a sine wave, but the frequencies of channels 1 and 2 are different? Does it do this measurement automatically? Thanks.

Can you do tuner alignments with this? How high does the generator go?

Can you use a powerbank to power the scoop? Or is it also battery powered? And please could you tell me the vertical sensitivity? I am looking for a battery powereld scope with about 5mV sensitivity

Are you going to make a video lesson about "flying probes"?

DSO2C10 VS DSO5102P. Which one is better?

I am a fan of that fan!!

Thanks Paul. What was the memory depth on the FFT?

@englishrupe01

3 жыл бұрын

Spec says 8M, Eddie.

Greetings 🙏 Please recommend which is better for a beginner. Hantek DSO2C10 or DSO2D10 or Fnirsi 1014D. Is Hantek DSO2C10 is better then DSO2D10?

It's often a waste of time offering serious answers to questions about what our knob-forested test gear does (and how many we actually need... all of them, duh) so I sometimes just say the oscilloscope is a twiddly pressy activity centre for nerds. The control test feature on this scope looks like designers decided we'd actually enjoy that, and I think they're right!

Very Nice ! Thank you .

Should this scope be able to accurately read dc voltage?? 13.8v reads 14.1v on ch2 and 14.0 on ch1 a aa battery reads 1.6 when its actually 1.44v is this normal behavior? Ive tried everything. 😪

BTW you said you couldn't see the recalled waveform. Maybe it would've been better to switch to square wave for the live one, but I certainly thought you could see the greyed/ghosted image of the saved sine wave when you recalled it

I enjoy your videos. Thanks for the effort in making them. They have inspired me to order some basics and start playing. I do have one request and it is a variation of things you have done. How about a video on making a randomly flashing LED? I have figured out the 555 on some level and I realize it would take a few more components to do this but I would like a little more info on generating a "random" length, variable pulse. I'm thinking like controlling an LED, MOSFET or BJT making them go on and off at randomly changing intervals and lengths. Another thing I think folks would be interested in would be speakers. Like having speakers be the analog input to control something, and LED, switch, transistor, etc....

@2pist

3 жыл бұрын

Dig around the web and you will find someone has done it more than likely. If not, you may come across something similar you can reverse engineer. I wanted to design a switching power supply for a car amplifier when I started out so I cobbled together a 556 timer and some junk somehow made it work using an old amp as a guide. Sadly my level of sophistication hasn't changed the last 20 yrs until I too bought this scope. Lol.. it's a fun yet frustrating hobby.

Hi Paul, love your channel...great info and always broken down to a novice level. Can you give your opinion on this scope vs the DSO5102P and the DSO4102 that you have reviewed in the past. If you had to choose, which one would you prefer? Thanks

@pedromillan927

3 жыл бұрын

Dso5102P. Of course.

@lalu225

2 жыл бұрын

@@pedromillan927 Can you give some more details on why please? I'm thinking of buying an entry level oscilloscope

@pedromillan927

2 жыл бұрын

@@lalu225 you can upgrade it with a simple update to 200Mhz

Thank you! 🙏

I would've appreciated more if you show us the formats that can be saved through the USB plug and how !!

Very good.Thank you.

Can you do a video detailing the video trigger functions, like displaying an NTSC composite signal? Thanks.

@learnelectronics

2 жыл бұрын

check my oscilloscope playlist

Hey Paul, nice video. Mine didn't arrive yet but I have a question if you have the time to answer: This model doesn't have the function generator, but the buttons are there... can be "software activated", is just a software issue? Did you notice that the board has written DSO2D15... It seems they all use the same board. Kudos Hugo.

@learnelectronics

3 жыл бұрын

As far as i know, yes you can. Someone, a French dude sent me hack for it. Email me @ arduino0169@gmailcom

Thanks. i think im gona get this one thinking i have a ryobi 150 watt battery inverter to run it free of mains

Overall as a beginner scope, it looks good, especially the decoding but I don't like them shorting you a probe. Thanks, Paul.

Ahhh ordered it a week ago and still waiting for it to ship :( really want it now

I'm looking at this model for tube amp work. The fnirsi has the signal generator, though. I wonder what one I should get. I have an old smart phone I can use as an audio generator I guess

Does it have a fan?

I don't see this on your workbench in later videos, so did you decide to keep it? Could you (easily) remove the red tab and the protective film (it is between the case and the LCD)? If you do decide to do a follow-up video e.g. using the trigger of serial protocols (would be good) then turning off the sound in the utility menu is a good way to go? There is a useful function that remembers all the last settings e.g. V/div, horizontal timebase, etc. if you don't twiddle knobs for about 10 seconds. Later, if (probably when) changing the settings causes the system to hang and you have to power the unit off and on, it will be exactly as you left it. I like that "feature" a lot and it's better than nothing. The print menu can be bypassed by directly using the "Save to USB" button. It is a good idea to copy all existing screen prints to a "Saved" folder before starting to save a bunch of prints because the files are not time/date stamped and it can get confusing if you have new ones mixed in with old ones. Only one probe? To be fair, Amazon's description does say only one probe is provided.

@learnelectronics

3 жыл бұрын

I have over 20 scopes. That one is on the shelf for now. I was able to pull the film off.

Thank you !

Nice.Thanks

Can i travel with oscilloscopes in flight is possible?

Hello Paul thank you. Very in formative. Coincidentally I’m still looking for a decent scope for a little above beginner level. How would you compare this one to a Rigol DS1054Z or the Hantek 5102P?

@dsfryda

3 жыл бұрын

Hello Paul, I would defiantly go with the Rigol. You can find online the update hack that will give you 100MHz, 24MB memory depth instead of 8MB and all the trigger modes. The interface is much better and polished. And if you haven't checked it out, go to the EEV BLOG channel and see the review Dave did on the Rigol, you'll be sold.

@walter....

3 жыл бұрын

If you don't need 4 channels, there's also the newer Rigol DS1102Z-E which is basically a DS1054Z with only 2 channels, but it comes with 100 MHz and all triggering modes and protocol decoding already enabled officially. You can get that for under $300.

@excitedbox5705

3 жыл бұрын

Up until 1 1/2 years ago Hantek was best value by a wide margin. Lately the scopes from other vendors have been getting cheaper but the entry scopes still don't match their features. Rigol etc charges for unlocking things like higher speeds or signal analyzers which Hantek gives you for free.

@Todestelzer

3 жыл бұрын

@@dsfryda Absolutely. Buy it and hack it. Really easy to do. Very nice scope, I like it a lot.

Thank you

Vale apena comprar?

Hello there! How can I join your patreon channel sir? I found your videos are very interesting. Thanks and more power to this channel.

So my DSO2D10 arrived couple of days ago and spotting how to change the serial trigger data/address value is tricky. But look at page Two of the trigger menu and look at the F4 Data Value. Look really carefully and you will two little Red Dots these indicate which value you are changing high/low digit press and turn V0 to select the digit and same to shift between value and high/low digit. Tricky but easily mastered when you figure it, hope that helps :-)

That USB Type-A port on the back -- is that for connecting to a host computer?

@learnelectronics

3 жыл бұрын

Yes

Can this be used as a digital multimeter? If so how? This is my first scope and so far I'm pretty lost. I also want to use it to check capacitor polarity but can't figure that out either.

@learnelectronics

3 жыл бұрын

It has a multimeter function

Thanks for reviewing this. I got confused and ordered one thinking that the waveform generator worked. Damn. Have you tried the remote control feature? Do you know if it works in Linux? Thanks again.

@learnelectronics

3 жыл бұрын

It is Linux. I havent used the remote control feature, but Im sure it's Labview compatable.

@th3drizzl378

3 жыл бұрын

check eevblog forum u can convert most of the c's to the d model and they did figure out linux

@James_Bowie

2 жыл бұрын

AFG only available in models DSO2D10 and DSO2D15.

17:55 There should be some way to see the actual licences for the open-source software being used. Presumbly it will also list the names of the software packages. Could it be running a Linux kernel?

@learnelectronics

3 жыл бұрын

I'm sure its running Linux

how about protocol capture?

Did you calibrate probe

Nice scope Paul - only downer is the omission of the 2nd scope probe and possibly no fan but perhaps none needed - ha ha they know guys like you open their scopes so they scrubbed the chip info off....now you will have to xray it! When I googled "lemontree chips" I get ads for potato chips 🤡 Overall a good value for under $300 especially with the built in decoder and other features. I like the different colors they used for the front panel LEDs. How would you compare Hantek scopes to Keysights with similar features? Is Keysight worth the extra $$$. Last year I bought a Siglent 200 MHz 2 ch scope (about $429) with part of my stimulus money been very happy with it.

hello every body, few days ago the Hanteck dso2D10 arrives in my house. I tried the SINGLE mode. Everything works with Edge RISING, but nothing work with Edge FALLING (or Either). someone have found the same as me ??

Hello.Does it have the digital filter like RIGOL DS1052E? Repetitive signal 60MHz sine wave was fluctuating and some distortion,a bit shame,but acceptable,because it has the serial bus decoding(address/data trigger etc>Considering the price,very interesting.Thanks.

@learnelectronics

3 жыл бұрын

20Mhz bandwidth limiting only

@dragonfly333yyt

3 жыл бұрын

@@learnelectronics Thanks for information.

@mugabirapaul8653

3 жыл бұрын

Is it OK for laptop repairing field

Thanks for the excellent review. I ordered that exact same model (with an extra 150MHz probe) about a week ago, still waiting for it to be shipped though. Will comment again when I have received it. Edit: FedEx delivered it today, and I am very impressed. It's not quite at the same quality level as an HP or Tektronix scope, but it's decent enough, looks good and performs adequately, and it's unmatched in terms of value. Very happy with my purchase!

It would be interesting to know if that same circuit board is used in their "upgraded" scopes. Is that same board used in the 100MHz, 150MHz & 200MHz scopes. If so, then software determines band width. Probably a flag in the software that limits the 'scope's bandwidth and not the hardware.

So this does not need a cd first usb

hi between this and owon sds1102 which one would you recommend?

@learnelectronics

3 жыл бұрын

Watch Monday's video....

I bought one with a couple of extra probes including a 10X probe.

Hey Jan 2024 I just took mine out of box. Same model. I have two orobes plus cable with pos and neg clips.

thanks. love your vids. you've helped me get to the point in my electronics hobby that I bought my first oscilloscope and this is the one I bought. $187 @ Amazon today. I'd love to know what

@learnelectronics

7 ай бұрын

Hantek DSO2d15 for $216 amzn.to/3QResd3

Hello, my friend. I see you have a 735 ballcap on your bench. I'm a retired ETCS(SS/SW) (NavET) and was the first ship superintendent on Pennsylvania at TRF. Good to find your channel. Later, John

@learnelectronics

2 жыл бұрын

STS2 here

I just received my DSO 2D15 …..can it be upgrade to 200Hz?

@learnelectronics

2 жыл бұрын

It's a software upgrade. I'm sure it's possible. Check the EeVblog forums.

Hi, please is this scope good for serial decode? Thanks :)

@learnelectronics

Жыл бұрын

Not really

Hantek DSO5102P USB Storage Oscilloscope Oszilloskope 2 Channels 100MHz 1GSa/s Is there any difference between the two scope I can't figure out of I should buy this over any of the other ones. Is this missing anything I might need in the future?

@simeonmihaylov6123

3 жыл бұрын

Judging by the questions you are asking... the DSO5102P might be more than enough, however this is newer and I believe better. Being said that, I have still the 5102P and for my needs is more than enough. The difference is around 20-30$ in Aliexpress... Personally if I hadn't any scope at all and I need to buy a relatively good new one on the budget side - I would take this one.

@learnelectronics

3 жыл бұрын

5102P lacks protocol decoding and all of the trigger functions of the 2c10

I've been thinking about this lately. Is there any reason a first time oscilloscope buyer (read: complete noob like me) would want or need a four-channel device instead?

@learnelectronics

3 жыл бұрын

Not really

@sirnukesalot24

3 жыл бұрын

Thanks!

so what would WAVE GEN button do on DSO2C10? Isn't waveform generator only available on DSO2D10/15 model?

@learnelectronics

2 жыл бұрын

It does nothing.

Hello!!! Please tell me, what is its height when installed on the legs, up to the top point?

@learnelectronics

Жыл бұрын

just about 7 inches

I got a similar oscilloscope for 139€ (brand OWON) which is an absolute winner in this price range. It's doing what I expect it to do, nothing more nothing less. It will replace my very old crt oscilloscope.

@kangtukang4948

3 жыл бұрын

what series owon oscilloscope sir?

Awesome entry scope. One thing I see that's particularly nice about this Hantek versus the Rigol DS1000Z series is that the Hantek can turn off the menus and use the full screen for signal display while the Rigol always has menu columns taking up portions of the left and right sides. Plus it's not much more to step up to the Hantek DSO2D10 to get a 5MHz waveform generator. (DSO2D10 $ 280 on Amaz on today). Even if you wound up having to buy a second probe this scope's a real bargain.

Looks like a nice scope. What about a fan? Does it need it? Now that the thing was opeened up, did that void the warranty?

@learnelectronics

3 жыл бұрын

There was no warranty sticker, so...

Hi. When I am pressing "WAVE GEN" Button on DSO2C10, it is showing "Signal source not supported". Could this mean that this model does not support Wave Form Generator?

@learnelectronics

2 жыл бұрын

Yes

If you don't mind waiting until Christmas they are on Banggood USA for $205.99. I would rather buy from Amazon, get it in two days and if I have a problem it won't take three months to correct. I like Hantek's scopes but if I buy one more I'll be living in the garage. Great review Paul. You can't beat Hantek on cost vs capabilities. Nice little unit.

@excitedbox5705

3 жыл бұрын

You can buy on Aliexpress for cheaper and still get it shipped from your country. I ordered Mine and it arrived in

@2pist

3 жыл бұрын

Getting something in the US from China in 2 days is as probable as a Scotsman wearing underwear I'm afraid.

I'm 37 and just started getting into electronics a couple of years ago. Well, I've tinkered with electronics here and there since I was really young but just started building my own circuits the last couple of years. An oscilloscope is about the only piece of equipment I still have yet to get. I've been out of work for about a year now due to health reasons and just can't afford one right now. In your opinion/experience are the cheap small ones like the Q15001 worth buying? I can't even afford one of them at the moment lol but will probably be about the only one I'd ever be able to get with the way things have been going lately lol.

@ibnewton8951

3 жыл бұрын

My advice ERIC is for you to purchase a Rigol 1054Z 4 channel 50 MHz scope. It’s outstanding value for around $300.00 or so.

@heinz-57

3 жыл бұрын

@@ibnewton8951 Unless you have a coupon for about 90% off of that price I'm gonna have to pass cause that's about all my budget at the moment will allow for lol.

@Broken_Yugo

3 жыл бұрын

Those little cheap handheld scopes aren't totally useless but are ultimately low bandwidth toys. You're better off trolling your local marketplace sites and trying to score an old 2 channel bench scope for $50 or so.

@heinz-57

3 жыл бұрын

@@Broken_Yugo Thanks for the info 👍

I have order one this from banggood. Waiting.

It's worth mentioning that Hantek don't include a ground spring with their probes, only the standard 15cm/6" ground lead with a crocodile clip, which is a shame. You can of course make your own, or buy them for a couple of £

Cual me recomendarías? DSO5202P vs DSO2C10? Te lo agradezco,excelente contenido,saludos desde chile

@pedromillan927

3 жыл бұрын

Como nadie aquí te va a responder ya te respondo yo. Básicamente hacen los dos lo mismo y lo único que importa en un osciloscopio digital es el ancho de banda y la memoria. Cuanto más ancho de banda, mejor. No hace falta que te pilles un 5202, es el 5102 con una actualización y por firmware puedes liberarlo a 200mhz. Y pasa algo similar al 2c10/15 con una actualización puedes liberarlo a 159mhz. Lo que nadie cuenta de hantek es que sus anchos de banda son siempre mediante resoluciones de firmware, realmente ninguno traga más de 66mhz.

@pedromillan927

3 жыл бұрын

Pillate un Rigol 1054 eso es la poya.

@tomasgonzalez6810

3 жыл бұрын

@@pedromillan927 muchas gracias por responder,finalmente encargué el DSO2C10 ,principalmente lo quiero para aprender ( preferí ese entre el finris que era más económico)

@pedromillan927

3 жыл бұрын

@@tomasgonzalez6810 esta bien. Ya sabes que todos los dso2xCx se pueden liberar a su escala inmediatamente te superior de ancho de banda. En tu caso puedes convertirlo a un dso2C15 únicamente cargándose la actualización apropiada.

Nice video Bubblehead, DBF

Amazon shows this unit in both a Lab version and a Benchtop version. Lab version comes with only one probe, Benchtop version comes with two. Lab version is about $30 more. What's the difference between them? If you want a built-in signal generator go for the DSO2Dxxx variant - DSO2Cxxx does not contain AWG.

@learnelectronics

3 жыл бұрын

I don't know.

my old 10 mhz heath-kit scope I built in the 80's gave up the ghost ... this will be a good replacement and I don't have to have a 18" long cabinet taking up room on the bench...

@learnelectronics

2 жыл бұрын

Yes the new scopes are much thinner.

The little scopes they have these days... I just found your channel and noticed the Pennsylvania Hat right off the bat. What flavor of Bubblehead Tech were you? I was a NavET and still have nightmares about hauling the old Tektronix 545s up to the tender. When you think that this little sub $300 scope more than matches everything we could do with the $8k Tektronix beasts from back in the day, and way more... Subscribed, interested to see what you've got coming up.

@learnelectronics

3 жыл бұрын

STS...Yeah this little cheapo scope blows the Tek behemoths out of the water.

@brendajanes4139

3 жыл бұрын

I actually have been thinking about getting a Hantek scope, but I still love my Tektronix 500 series scopes, (531A, 535A, 545A, 561A, 564, RM565, and my 503), Those scopes are still up and running at this time. I just worry about how long the Hantek will last. Most likely my Tektronix scopes will still be up and running 20 years from now. I am still learning on how to do all the math.

Hello, what is the difference between the one you showed and the DSO5102 ? thanks

@learnelectronics

2 жыл бұрын

Upgraded software and onboard AWG (both scopes have the footprints for the AWG on the main board. But only the d model has the footprints populated and a functioning AWG. I suspect you could populate this footprints and make it work)

@hichamtassi1753

2 жыл бұрын

@@learnelectronics Thanks for the info !

Hi so are you saying there is no digital read out of the input frequency going into the oscilloscope ?

@learnelectronics

3 жыл бұрын

No, its there, under measurements. But most scopes have an option to turn it on permanently. I can not find it on this one

@johnniehancock2426

3 жыл бұрын

@@learnelectronics It's part of the DVM.

@2pist

3 жыл бұрын

It is part of the DVM, but mine only shows zeros.. Must be some setting somewhere I hope.

FYI I just ordered one of these off of Amazon, and mine came with two probes. Your box was probably just a one-off fluke that was packed in error.