Mental Hull Titanic by Hachette, Engine room test !
Жүктеу.....
Пікірлер: 59
@johnnyhollis9977 Жыл бұрын
The set up looks quite good now, good job! However, the centre propeller was almost certainly a 3 bladed jobbie! Pictures available are from the RMS Olympic in dry dock and show a 4 bladed propeller. A recent note book found from an engineer shows quite clearly that the Titanic was fitted with the 3 bladed propeller at the time of sailing. This has been quite a controversial point until recently. The good news is that replacements are easy enough to buy if Hachette don't pop one in as an alternative later in the build! Good luck with it! 😉
@kevinb897
Жыл бұрын
Yes your right , it should be three blade on the centre propeller, Hachette have got a few things wrong so far such as colours of some parts !
@jamesgroccia644
Жыл бұрын
The big cranks on the outboard side of the engines should not move, those arms connect the drive rods to the reversing engines.
@joeerickson5162 ай бұрын
"Great!" 👍
@titaniccor6502 Жыл бұрын
Wow, awesome build!
@rodadams8422 Жыл бұрын
Fantastic buddy looks really nice 👌
@lorenzomodellismo Жыл бұрын
Bravo continua così 👍👍👍💪💪👍
@bienenschulze1 Жыл бұрын
Looks good…👌🏽
@dedesmodelatelier Жыл бұрын
Bonjour, superbe, nous en France ne sommes pas encore si loin !
@johndoe528 Жыл бұрын
Super cool. I hate to be that guy, but it would really benefit from a quiet motor / geartrain. Perhaps something brushless and turning at a lower RPM
@davef.2329 Жыл бұрын
Really neet!!! Nice work.
@kevinb897
Жыл бұрын
Thank you! Cheers!
@jayrobinson7554 Жыл бұрын
Looks brill 👍 just finally got mine engines finished they was a nightmare i hated doing them, so fiddley and awkward
@kevinb897
Жыл бұрын
I agree with you a bit fiddley !
@pip12111 Жыл бұрын
Going full reverse sealed her fate. If they kept that center screw turning it would have forced water against the rudder,and she could have turned faster
@cras07
Жыл бұрын
The engines were not commanded full astern in the attempt to avoid the iceberg.
@Robabin
Жыл бұрын
The engines where actually commanded all stop, so no water was being forced against her rudder
@bayerischemotorenwerke5252
Жыл бұрын
There was no iceberg
@Robabin
Жыл бұрын
@@bayerischemotorenwerke5252 There was lmao
@bayerischemotorenwerke5252
Жыл бұрын
@@Robabin no
@shawnlittle3091 Жыл бұрын
Pretty cool model the engine room is pretty accurate too bad the turbine room and the electrical engine room isn’t accurate but still a cool model.
@hectorruffo8947
11 ай бұрын
Grave error de diseño de la réplica. Los vástagos de las válvulas invaden el camino diseñado para el mantenimiento del motor . Causarían la muerte de los mecánicos de mantenimiento. Fácil de ver .
@AnthraciteHorrorStories Жыл бұрын
How'd you do this?!
@Shamshiadadd10 ай бұрын
Great work but omg the noisy motor...
@kevinb897
10 ай бұрын
Yes, I know it is noisy, but once it's inside the ship, hopefully, it won't be as bad !
@andymunns2579 Жыл бұрын
Curious to see the wyper arms on the Stephenson gear see sawing too and fro - normally these are fixed by gib head keys to the wyper shaft and not independent. They will be either in or out for Ahead or Astern - Pls can you explain? Also correct that in Ahead, the centre exhaust turbine drives its propeller, and in Astern, the centre propeller is idle.
@kevinb897
Жыл бұрын
It's a model kit and that Is the way it is assembled, so it's down to the manufacturer of the kit , there is a few things on this model that are not accurate !
@warjakeboy3 ай бұрын
what issues are them
@robertnicholls23163 ай бұрын
Hi Which parts would you need to buy if you just wanted the engine parts
@kevinb897
3 ай бұрын
You will need issues 3. 5.6.7 and 10, then issues 26 to 40. I'm not sure if they are still available, but try Hachette partworks
@helpelaine3927 Жыл бұрын
I came across someone selling these Hachette Titanic magazines, (they gave up on buying all 140 issues) I purchased issue 3 that has parts for the one engine and smoke generator, If I'm only interested in building the two engines and driveshafts, props, which other issues do I need to get? Thanks for any help you can offer. Kind regards.
@kevinb897
Жыл бұрын
You will need issue 3.5.6.7.10.then all issues from 26 to 40, if that helps your best bet, are to get them from Hachette as you can buy separate issues !
@helpelaine3927
Жыл бұрын
@@kevinb897 thank you so much!
@kevinvicedomini8745
Жыл бұрын
I got same problem everything to do with engine room has gone wrong
@kevinvicedomini8745
Жыл бұрын
I checked issues I need to start over and too much to pay and early issues are not available
@kevinb897
Жыл бұрын
You could try phoneing Hachette Partworks and they will probably be able to get the issues you need but may have to wait for them to come back in stock !
@kevinvicedomini8745 Жыл бұрын
I've had problems with my engines . I feel like giving up. Unless I get relevant issues to rebuild new ones
@kevinb897
Жыл бұрын
I had to take appart one engine because it wasn't turning properly, but all OK now just take your time !
@kevinvicedomini8745
Жыл бұрын
@@kevinb897 I can't take apart because of parts that needed glue
@bayerischemotorenwerke5252
Жыл бұрын
@@kevinvicedomini8745 lol
@yiman7370 Жыл бұрын
I wish I can buy this
@kevinb897
Жыл бұрын
Just look up Hachette Partworks you can get the Model kit from them !
@hectorruffo89479 ай бұрын
Los brazos de las bielas pasan sobre la pasarela de mantenimiento. Peligro mortal para los mecánicos que circulen sobre ellas . Gran error .
@rustyrelicsfarm2406 Жыл бұрын
Would you be abke to put these in a model?
@kevinb897
Жыл бұрын
Yes, it will eventually go into the Hachette 1/200 scale model of the Titanic of which I'm building !
@CharlyLucky0397 Жыл бұрын
No entiendo por qué las élises giran en sentidos contrarios..
Пікірлер: 59
The set up looks quite good now, good job! However, the centre propeller was almost certainly a 3 bladed jobbie! Pictures available are from the RMS Olympic in dry dock and show a 4 bladed propeller. A recent note book found from an engineer shows quite clearly that the Titanic was fitted with the 3 bladed propeller at the time of sailing. This has been quite a controversial point until recently. The good news is that replacements are easy enough to buy if Hachette don't pop one in as an alternative later in the build! Good luck with it! 😉
@kevinb897
Жыл бұрын
Yes your right , it should be three blade on the centre propeller, Hachette have got a few things wrong so far such as colours of some parts !
@jamesgroccia644
Жыл бұрын
The big cranks on the outboard side of the engines should not move, those arms connect the drive rods to the reversing engines.
"Great!" 👍
Wow, awesome build!
Fantastic buddy looks really nice 👌
Bravo continua così 👍👍👍💪💪👍
Looks good…👌🏽
Bonjour, superbe, nous en France ne sommes pas encore si loin !
Super cool. I hate to be that guy, but it would really benefit from a quiet motor / geartrain. Perhaps something brushless and turning at a lower RPM
Really neet!!! Nice work.
@kevinb897
Жыл бұрын
Thank you! Cheers!
Looks brill 👍 just finally got mine engines finished they was a nightmare i hated doing them, so fiddley and awkward
@kevinb897
Жыл бұрын
I agree with you a bit fiddley !
Going full reverse sealed her fate. If they kept that center screw turning it would have forced water against the rudder,and she could have turned faster
@cras07
Жыл бұрын
The engines were not commanded full astern in the attempt to avoid the iceberg.
@Robabin
Жыл бұрын
The engines where actually commanded all stop, so no water was being forced against her rudder
@bayerischemotorenwerke5252
Жыл бұрын
There was no iceberg
@Robabin
Жыл бұрын
@@bayerischemotorenwerke5252 There was lmao
@bayerischemotorenwerke5252
Жыл бұрын
@@Robabin no
Pretty cool model the engine room is pretty accurate too bad the turbine room and the electrical engine room isn’t accurate but still a cool model.
@hectorruffo8947
11 ай бұрын
Grave error de diseño de la réplica. Los vástagos de las válvulas invaden el camino diseñado para el mantenimiento del motor . Causarían la muerte de los mecánicos de mantenimiento. Fácil de ver .
How'd you do this?!
Great work but omg the noisy motor...
@kevinb897
10 ай бұрын
Yes, I know it is noisy, but once it's inside the ship, hopefully, it won't be as bad !
Curious to see the wyper arms on the Stephenson gear see sawing too and fro - normally these are fixed by gib head keys to the wyper shaft and not independent. They will be either in or out for Ahead or Astern - Pls can you explain? Also correct that in Ahead, the centre exhaust turbine drives its propeller, and in Astern, the centre propeller is idle.
@kevinb897
Жыл бұрын
It's a model kit and that Is the way it is assembled, so it's down to the manufacturer of the kit , there is a few things on this model that are not accurate !
what issues are them
Hi Which parts would you need to buy if you just wanted the engine parts
@kevinb897
3 ай бұрын
You will need issues 3. 5.6.7 and 10, then issues 26 to 40. I'm not sure if they are still available, but try Hachette partworks
I came across someone selling these Hachette Titanic magazines, (they gave up on buying all 140 issues) I purchased issue 3 that has parts for the one engine and smoke generator, If I'm only interested in building the two engines and driveshafts, props, which other issues do I need to get? Thanks for any help you can offer. Kind regards.
@kevinb897
Жыл бұрын
You will need issue 3.5.6.7.10.then all issues from 26 to 40, if that helps your best bet, are to get them from Hachette as you can buy separate issues !
@helpelaine3927
Жыл бұрын
@@kevinb897 thank you so much!
@kevinvicedomini8745
Жыл бұрын
I got same problem everything to do with engine room has gone wrong
@kevinvicedomini8745
Жыл бұрын
I checked issues I need to start over and too much to pay and early issues are not available
@kevinb897
Жыл бұрын
You could try phoneing Hachette Partworks and they will probably be able to get the issues you need but may have to wait for them to come back in stock !
I've had problems with my engines . I feel like giving up. Unless I get relevant issues to rebuild new ones
@kevinb897
Жыл бұрын
I had to take appart one engine because it wasn't turning properly, but all OK now just take your time !
@kevinvicedomini8745
Жыл бұрын
@@kevinb897 I can't take apart because of parts that needed glue
@bayerischemotorenwerke5252
Жыл бұрын
@@kevinvicedomini8745 lol
I wish I can buy this
@kevinb897
Жыл бұрын
Just look up Hachette Partworks you can get the Model kit from them !
Los brazos de las bielas pasan sobre la pasarela de mantenimiento. Peligro mortal para los mecánicos que circulen sobre ellas . Gran error .
Would you be abke to put these in a model?
@kevinb897
Жыл бұрын
Yes, it will eventually go into the Hachette 1/200 scale model of the Titanic of which I'm building !
No entiendo por qué las élises giran en sentidos contrarios..
Carica altri video
Link to buy
@kevinb897
Жыл бұрын
Hachette Partworks, or Agora models !