Charge cables are on plasticaround the battery terminals! Connect it to the metal part of the battery terminals.

your hooked to plastic on the positive side of "charger" lmao. on both sides lmao. this is gold folks

@jakerarcega2701

4 жыл бұрын

Qqqqqqqqq1qqqqqqqqqqqqàppp0pp0pp00

Take a breath bud. Lol thanks for the video. It helped.

your the man bro....

How did you get your battery to fit in your under seat storage area?

Your video was 4 years ago, so I hope you learned basic electricity since then.

I sold my scooters but I still love scooters! Good luck with your store. .

@NCYSTORE

3 жыл бұрын

Thank you

Buongiorno io dovrei cambiare la lampadina della freccia sinistra come posso fare per sostituirla

Great video

When he says "generator" he means "charger".

So true

You have some awsome content,,I just got a 150cc for really cheap, it looks great, was told it was caught in a rain storm and never started since, it looked like the guy tried to do some things but gave up and sold it. When I hookup a battery and turn the key I get no lights or no power, where should I start to troubleshoot this? Thank you for you videos

@aaaaandstilllll_____9855

Жыл бұрын

New battery!?

@michaelcooper10

Жыл бұрын

Check all the fuses

Its helpful buddy! But please buy a camera holder 😑

Hey bud we have a similar scooter it has a 15a fuse just b4 the ignition coil keeps blowing ideas?

@subzero5101

4 жыл бұрын

Id just eliminate it. I have two similar scooters and the only fuse is between the rectifier and the battery to safely charge. Theres really no need. I suspect its there by mistake.

@michaelwhittman1956

4 жыл бұрын

@@subzero5101 nice

On the gy6 do u got to hold the right brake handle to start it

@NCYSTORE

3 жыл бұрын

yes

My to a scooter got new everything on it and still won't start.when it do start it'll run for 30 sec and cut off and won't start for a long time.can u help?

@NCYSTORE

5 жыл бұрын

Check the battery even though it reads good it might not be good that's why I find out the end replace the battery

@gmindgjerd

5 жыл бұрын

Check /clean both air and fuel filter.Dismantle and clean carburettor Fresh gasoline. I guess.

@subzero5101

4 жыл бұрын

Sounds like your float is stuck or your line is clogged. The float bowl lets it run until its used up and then slowly fills and you do it all over again. Like mostly harmless said a good cleaning of the carb disassembled in an ultrasonic cleaner does wonders. Try not to use gas with ethanol. Its the source of most toys not running after being stored all winter.

@markbauer909westend

4 жыл бұрын

Go to the parts store and get some Seafoam. Put it in your tank and save yourself the headache of pulling your carburetor apart.

Well done.very cler

I just replaced my stator and still getting no spark. Brand new ncy cdi brand new coil brand new battery brand new relay and still no spark. Tested it with 2 other cdis and still no spark. Stator and everything tests good. Why can't I get power from my cdi to spark plug?

@aaaaandstilllll_____9855

Жыл бұрын

Broken wire some where or kill switch is on or broken

@aaaaandstilllll_____9855

Жыл бұрын

Or even bad cdi, even if it's new

WOAH WOAH WOAH WOAH!!!!! HOLD UP!!! .... as a master mechanic, i want to correct you @7:57 dielectric grease is not good for conductivity!! dielectric grease is NON-CONDUCTIVE and should NEVER be put on any connections. its good to weatherproof electric connector seals such as sparkplugs. it should only be applied to the ribs of the ceramic and not any metal connections. do not put dielectric grease in a bulb socket or even a harness connector. if the connector has a seal put dielectric grease on the seal to help the seal, seal better and prevents sticking. dielectric grease should be put on the outside plastic part of the smaller connection in order to seal properly . never place it inside of the bigger connector to where it has risk of touching either male or female metal connectors inside of the plug. its best to never apply any dielectric grease to a battery connector due to the heat and making it thin out and seep into the connections causing the dielectric grease which is NON-CONDUCTIVE, to cause a break in connection and either wont start or wont charge and putting you in a situation where you need to use your kickstart if you have one. never put dielectric grease on threads either. always use Copper anti-seize as it has copper material in it and improves connection to ground. copper has the best conductive properties and it being formulated into anti-seize makes it perfect to protect your battery terminals and a grease to put on your sparkplug threads. Thank you for reading!

Hi brother

Anybody..... Can u get spark without a cdi box?

@giovannironda2926

4 жыл бұрын

No

once the blind leading the blind it the earth. son you haven't got your earth corect . had you pot your erth to the live on your selonied you would have proven- you mistake. never Assume a fault prove the fault son .

I think you need to replace your camera! Focusing is so bad!

I've worked on a bunch of scooters and watching you is a joke.

you jump form one thing to another and are not very clear in what your saying

Damn YT won't let me watch the vid

So now the purpose of that is that okay the battery is bad replace it I mean you're not answering any questions I'm not wasting f****** 33 minutes sitting here watching you show me all the tools you have

As!

Video didn't say much of anything of importance.

i dont understand what you are saying

@NCYSTORE

3 жыл бұрын

what part mainly?

@geo_5067

3 жыл бұрын

@@NCYSTORE the faucet thing

@NCYSTORE

3 жыл бұрын

@@geo_5067 it's a metaphor for how current flow like water through a pipe or water hose and volume of water or pressure flows current measure as volts. You can find other KZread detail electricity.

@geo_5067

3 жыл бұрын

@@NCYSTORE ohhhhh OK

you are too long winded in your detailing of trying to crank scooter. It becomes boring and unwatchable for me. I willl find another person to watch